An integrative review on the applications of 3D printing in the field of in vitro diagnostics

Abstract Background The bone regeneration of artificial bone grafts is still in need of a breakthrough to improve the processes of bone defect repair. Artificial bone grafts should be modified to enable angiogenesis and thus improve osteogenesis. We have previously revealed that crystalline Ca10Li(PO4)7 (CLP) possesses higher compressive strength and better biocompatibility than that of pure beta-tricalcium phosphate (β-TCP). In this work, we explored the possibility of cobalt (Co), known for mimicking hypoxia, doped into CLP to promote osteogenesis and angiogenesis. Methods We designed and manufactured porous scaffolds by doping CLP with various concentrations of Co (0, 0.1, 0.25, 0.5, and 1 mol%) and using 3D printing techniques. The crystal phase, surface morphology, compressive strength, in vitro degradation, and mineralization properties of Co-doped and -undoped CLP scaffolds were investigated. Next, we investigated the biocompatibility and effects of Co-doped and -undoped samples on osteogenic and angiogenic properties in vitro and on bone regeneration in rat cranium defects. Results With increasing Co-doping level, the compressive strength of Co-doped CLP scaffolds decreased in comparison with that of undoped CLP scaffolds, especially when the Co-doping concentration increased to 1 mol%. Co-doped CLP scaffolds possessed excellent degradation properties compared with those of undoped CLP scaffolds. The (0.1, 0.25, 0.5 mol%) Co-doped CLP scaffolds had mineralization properties similar to those of undoped CLP scaffolds, whereas the 1 mol% Co-doped CLP scaffolds shown no mineralization changes. Furthermore, compared with undoped scaffolds, Co-doped CLP scaffolds possessed excellent biocompatibility and prominent osteogenic and angiogenic properties in vitro, notably when the doping concentration was 0.25 mol%. After 8 weeks of implantation, 0.25 mol% Co-doped scaffolds had markedly enhanced bone regeneration at the defect site compared with that of the undoped scaffold. Conclusion In summary, CLP doped with 0.25 mol% Co2+ ions is a prospective method to enhance osteogenic and angiogenic properties, thus promoting bone regeneration in bone defect repair.

Download Full-text

3D Printed Clamps for In Vitro Tensile Tests of Human Gracilis and the Superficial Third of Quadriceps Tendons

Applied Sciences ◽

10.3390/app11062563 ◽

2021 ◽

Vol 11 (6) ◽

pp. 2563

Author(s):

Ivan Grgić ◽

Vjekoslav Wertheimer ◽

Mirko Karakašić ◽

Željko Ivandić

Keyword(s):

3D Printing ◽

Fused Deposition Modeling ◽

Tensile Tests ◽

Biomechanical Properties ◽

Testing Procedure ◽

Laboratory Equipment ◽

Fused Deposition ◽

Custom Made ◽

3D Printed

Recent soft tissue studies have reported issues that occur during experimentation, such as the tissue slipping and rupturing during tensile loads, the lack of standard testing procedure and equipment, the necessity for existing laboratory equipment adaptation, etc. To overcome such issues and fulfil the need for the determination of the biomechanical properties of the human gracilis and the superficial third of the quadriceps tendons, 3D printed clamps with metric thread profile-based geometry were developed. The clamps’ geometry consists of a truncated pyramid pattern, which prevents the tendons from slipping and rupturing. The use of the thread application in the design of the clamp could be used in standard clamping development procedures, unlike in previously custom-made clamps. Fused deposition modeling (FDM) was used as a 3D printing technique, together with polylactic acid (PLA), which was used as a material for clamp printing. The design was confirmed and the experiments were conducted by using porcine and human tendons. The findings justify the usage of 3D printing technology for parts manufacturing in the case of tissue testing and establish independence from the existing machine clamp system, since it was possible to print clamps for each prepared specimen and thus reduce the time for experiment setup.

Download Full-text

The neurophysiology of ketamine: an integrative review

Reviews in the Neurosciences ◽

10.1515/revneuro-2019-0090 ◽

2020 ◽

Vol 31 (5) ◽

pp. 457-503

Author(s):

Rebecca McMillan ◽

Suresh D. Muthukumaraswamy

Keyword(s):

Spatial Scales ◽

Integrative Review ◽

Acute Effects ◽

Future Work

AbstractThe drug ketamine has been extensively studied due to its use in anaesthesia, as a model of psychosis and, most recently, its antidepressant properties. Understanding the physiology of ketamine is complex due to its rich pharmacology with multiple potential sites at clinically relevant doses. In this review of the neurophysiology of ketamine, we focus on the acute effects of ketamine in the resting brain. We ascend through spatial scales starting with a complete review of the pharmacology of ketamine and then cover its effects on in vitro and in vivo electrophysiology. We then summarise and critically evaluate studies using EEG/MEG and neuroimaging measures (MRI and PET), integrating across scales where possible. While a complicated and, at times, confusing picture of ketamine’s effects are revealed, we stress that much of this might be caused by use of different species, doses, and analytical methodologies and suggest strategies that future work could use to answer these problems.

Download Full-text

Nanoimprinted multifunctional nanoprobes for a homogeneous immunoassay in a top-down fabrication approach

Scientific Reports ◽

10.1038/s41598-021-85524-8 ◽

2021 ◽

Vol 11 (1) ◽

Author(s):

Hubert Brueckl ◽

Astrit Shoshi ◽

Stefan Schrittwieser ◽

Barbara Schmid ◽

Pia Schneeweiss ◽

...

Keyword(s):

Thin Film ◽

Nanoimprint Lithography ◽

Thin Film Deposition ◽

Film Deposition ◽

In Vitro Diagnostics ◽

Top Down ◽

Highly Sensitive ◽

Optical And Magnetic Properties ◽

Lift Off

AbstractMultifunctional nanoparticles are discussed as versatile probes for homogeneous immunoassays for in-vitro diagnostics. Top-down fabrication allows to combine and tailor magnetic and plasmonic anisotropic properties. The combination of nanoimprint lithography, thin film deposition, and lift-off processing provides a top-down fabrication platform, which is both flexible and reliable. Here, we discuss the material compositions and geometrical designs of monodisperse multicomponent nanoparticles and their consequences on optical and magnetic properties. The rotational hydrodynamics of nanoparticles is measured and considered under the influence of magnetic shape anisotropy in the framework of the Stoner-Wohlfarth theory. The plasmon-optical properties are explained by discrete-dipole finite-element simulations. Rotational dynamical measurements of imprinted nanoprobes for two test proteins demonstrate the applicability as highly sensitive biomolecular nanoprobes.

Download Full-text

The Inflammatory Role of Pro-Resolving Mediators in Endometriosis: An Integrative Review

International Journal of Molecular Sciences ◽

10.3390/ijms22094370 ◽

2021 ◽

Vol 22 (9) ◽

pp. 4370

Author(s):

Cássia de Fáveri ◽

Paula M. Poeta Fermino ◽

Anna P. Piovezan ◽

Lia K. Volpato

Keyword(s):

Intracellular Signaling ◽

Inflammatory Responses ◽

Therapeutic Potential ◽

Critical Role ◽

Integrative Review ◽

Inflammatory Factors ◽

Resolvin D1 ◽

Endogenous Factors

The pathogenesis of endometriosis is still controversial, although it is known that the inflammatory immune response plays a critical role in this process. The resolution of inflammation is an active process where the activation of endogenous factors allows the host tissue to maintain homeostasis. The mechanisms by which pro-resolving mediators (PRM) act in endometriosis are still little explored. Thus, this integrative review aims to synthesize the available content regarding the role of PRM in endometriosis. Experimental and in vitro studies with Lipoxin A4 demonstrate a potential inhibitory effect on endometrial lesions’ progression, attenuating pro-inflammatory and angiogenic signals, inhibiting proliferative and invasive action suppressing intracellular signaling induced by cytokines and estradiol, mainly through the FPR2/ALX. Investigations with Resolvin D1 demonstrated the inhibition of endometrial lesions and decreased pro-inflammatory factors. Annexin A1 is expressed in the endometrium and is specifically present in women with endometriosis, although the available studies are still inconsistent. Thus, we believe there is a gap in knowledge regarding the PRM pathways in patients with endometriosis. It is important to note that these substances’ therapeutic potential is evident since the immune and abnormal inflammatory responses play an essential role in endometriosis development and progression.

Download Full-text

Three-dimensionally printed polycaprolactone/multicomponent bioactive glass scaffolds for potential application in bone tissue engineering

Biomedical glasses ◽

10.1515/bglass-2020-0006 ◽

2020 ◽

Vol 6 (1) ◽

pp. 57-69

Author(s):

Amirhosein Fathi ◽

Farzad Kermani ◽

Aliasghar Behnamghader ◽

Sara Banijamali ◽

Masoud Mozafari ◽

...

Keyword(s):

Tissue Engineering ◽

3D Printing ◽

Bone Tissue Engineering ◽

Bone Tissue ◽

Three Dimensional ◽

Layer By Layer ◽

Composite Scaffolds ◽

3D Printed ◽

Co Doped

AbstractOver the last years, three-dimensional (3D) printing has been successfully applied to produce suitable substitutes for treating bone defects. In this work, 3D printed composite scaffolds of polycaprolactone (PCL) and strontium (Sr)- and cobalt (Co)-doped multi-component melt-derived bioactive glasses (BGs) were prepared for bone tissue engineering strategies. For this purpose, 30% of as-prepared BG particles (size <38 μm) were incorporated into PCL, and then the obtained composite mix was introduced into a 3D printing machine to fabricate layer-by-layer porous structures with the size of 12 × 12 × 2 mm3.The scaffolds were fully characterized through a series of physico-chemical and biological assays. Adding the BGs to PCL led to an improvement in the compressive strength of the fabricated scaffolds and increased their hydrophilicity. Furthermore, the PCL/BG scaffolds showed apatite-forming ability (i.e., bioactivity behavior) after being immersed in simulated body fluid (SBF). The in vitro cellular examinations revealed the cytocompatibility of the scaffolds and confirmed them as suitable substrates for the adhesion and proliferation of MG-63 osteosarcoma cells. In conclusion, 3D printed composite scaffolds made of PCL and Sr- and Co-doped BGs might be potentially-beneficial bone replacements, and the achieved results motivate further research on these materials.

Download Full-text

Application of 3D printed model for planning the endoscopic endonasal transsphenoidal surgery

Scientific Reports ◽

10.1038/s41598-021-84779-5 ◽

2021 ◽

Vol 11 (1) ◽

Author(s):

Xing Huang ◽

Ni Fan ◽

Hai-jun Wang ◽

Yan Zhou ◽

Xudong Li ◽

...

Keyword(s):

3D Printing ◽

Skull Base ◽

Transsphenoidal Surgery ◽

Three Dimensional ◽

Spatial Relationship ◽

Cranial Computed Tomography ◽

Imaging Data ◽

Endoscopic Endonasal ◽

Endoscopic Endonasal Transsphenoidal Surgery

AbstractThe application of 3D printing in planning endoscopic endonasal transsphenoidal surgery is illustrated based on the analysis of patients with intracranial skull base diseases who received treatment in our department. Cranial computed tomography/magnetic resonance imaging data are attained preoperatively, and three-dimensional reconstruction is performed using MIMICS (Materialise, Leuven, Belgium). Models of intracranial skull base diseases are printed using a 3D printer before surgery. The models clearly demonstrate the morphologies of the intracranial skull base diseases and the spatial relationship with adjacent large vessels and bones. The printing time of each model is 12.52–15.32 h, and the cost ranges from 900 to 1500 RMB. The operative approach was planned in vitro, and patients recovered postoperatively well without severe complications or death. In a questionnaire about the application of 3D printing, experienced neurosurgeons achieved scores of 7.8–8.8 out of 10, while unexperienced neurosurgeons achieved scores of 9.2–9.8. Resection of intracranial skull base lesions is demonstrated to be well assisted by 3D printing technique, which has great potential in disclosing adjacent anatomical relationships and providing the required help to clinical doctors in preoperative planning.

Download Full-text

Nanotomography of Cell Surfaces with Evanescent Fields

Advances in Optical Technologies ◽

10.1155/2008/254317 ◽

2008 ◽

Vol 2008 ◽

pp. 1-7 ◽

Cited By ~ 4

Author(s):

Michael Wagner ◽

Petra Weber ◽

Wolfgang S. L. Strauss ◽

Henri-Pierre Lassalle ◽

Herbert Schneckenburger

Keyword(s):

Total Internal Reflection ◽

3D Imaging ◽

Cell Swelling ◽

Cholesterol Depletion ◽

In Vitro Diagnostics ◽

Axial Resolution ◽

Cell Surfaces ◽

Cell Substrate ◽

Cell Topology

The technique of variable-angle total internal reflection fluorescence microscopy (TIRFM) and its application to nanotomography of cell surfaces are described. Present applications include (1) 3D imaging of chromosomes in their metaphase to demonstrate axial resolution in the nanometre range, (2) measurements of cell-substrate topology, which upon cholesterol depletion shows some loosening of cell-substrate contacts, and (3) measurements of cell topology upon photodynamic therapy (PDT), which demonstrate cell swelling and maintenance of focal contacts. The potential of the method for in vitro diagnostics, but also some requirements and limitations are discussed.

Download Full-text

3D Printing of Dapagliflozin Containing Self-Nanoemulsifying Tablets: Formulation Design and In Vitro Characterization

Pharmaceutics ◽

10.3390/pharmaceutics13070993 ◽

2021 ◽

Vol 13 (7) ◽

pp. 993

Author(s):

Mohammed S. Algahtani ◽

Abdul Aleem Mohammed ◽

Javed Ahmad ◽

M. M. Abdullah ◽

Ehab Saleh

Keyword(s):

3D Printing ◽

Solid Phase ◽

Immediate Release ◽

Water Soluble ◽

Solid Matrix ◽

Water Soluble Drug ◽

Poorly Water Soluble ◽

3D Printing Technique ◽

Poorly Water Soluble Drug

The 3D printing techniques have been explored extensively in recent years for pharmaceutical manufacturing and drug delivery applications. The current investigation aims to explore 3D printing for the design and development of a nanomedicine-based oral solid dosage form of a poorly water-soluble drug. A self-nanoemulsifying tablet formulation of dapagliflozin propanediol monohydrate was developed utilizing the semisolid pressure-assisted microsyringe (PAM) extrusion-based 3D printing technique. The developed formulation system consists of two major components (liquid and solid phase), which include oils (caproyl 90, octanoic acid) and co-surfactant (PEG 400) as liquid phase while surfactant (poloxamer 188) and solid matrix (PEG 6000) as solid-phase excipients that ultimately self-nanoemulsify as a drug encapsulated nanoemulsion system on contact with aqueous phase/gastrointestinal fluid. The droplet size distribution of the generated nanoemulsion from a self-nanoemulsifying 3D printed tablet was observed to be 104.7 ± 3.36 nm with polydispersity index 0.063 ± 0.024. The FT-IR analysis of the printed tablet revealed that no drug-excipients interactions were observed. The DSC and X-RD analysis of the printed tablet revealed that the loaded drug is molecularly dispersed in the crystal lattice of the tablet solid matrix and remains solubilized in the liquid phase of the printed tablet. SEM image of the drug-loaded self-nanoemulsifying tablets revealed that dapagliflozin propanediol monohydrate was completely encapsulated in the solid matrix of the printed tablet, which was further confirmed by SEM-EDS analysis. The in vitro dissolution profile of dapagliflozin-loaded self-nanoemulsifying tablet revealed an immediate-release drug profile for all three sizes (8 mm, 10 mm, and 12 mm) tablets, exhibiting >75.0% drug release within 20 min. Thus, this study has emphasized the capability of the PAM-based 3D printing technique to print a self-nanoemulsifying tablet dosage form with an immediate-release drug profile for poorly water-soluble drug.

Download Full-text

Fabrication and characterization of customized tubular scaffolds for tracheal tissue engineering by using solvent based 3D printing on predefined template

Rapid Prototyping Journal ◽

10.1108/rpj-08-2020-0186 ◽

2021 ◽

Vol 27 (2) ◽

pp. 421-428

Author(s):

Rudranarayan Kandi ◽

Pulak Mohan Pandey ◽

Misba Majood ◽

Sujata Mohanty

Keyword(s):

Tissue Engineering ◽

Cell Adhesion ◽

3D Printing ◽

Chemical Properties ◽

Contact Angle Measurement ◽

Angle Measurement ◽

In Vitro Cytotoxicity ◽

Content Type ◽

Tracheal Tissue

Purpose This paper aims to discuss the successful fabrication of customized tubular scaffolds for tracheal tissue engineering with a novel route using solvent-based extrusion 3D printing. Design/methodology/approach The manufacturing approach involved extrusion of polymeric ink over a rotating predefined pattern to construct customized tubular structure of polycaprolactone (PCL) and polyurethane (PU). Dimensional deviation in thickness of scaffolds were calculated for various layer thicknesses of 3D printing. Physical and chemical properties of scaffolds were investigated by scanning electron microscope (SEM), contact angle measurement, Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD). Mechanical characterizations were performed, and the results were compared to the reported properties of human native trachea from previous reports. Additionally, in vitro cytotoxicity of the fabricated scaffolds was studied in terms of cell proliferation, cell adhesion and hemagglutination assay. Findings The developed fabrication route was flexible and accurate by printing customized tubular scaffolds of various scales. Physiochemical results showed good miscibility of PCL/PU blend, and decrease in crystalline nature of blend with the addition of PU. Preliminary mechanical assessments illustrated comparable mechanical properties with the native human trachea. Longitudinal compression test reported outstanding strength and flexibility to maintain an unobstructed lumen, necessary for the patency. Furthermore, the scaffolds were found to be biocompatible to promote cell adhesion and proliferation from the in vitro cytotoxicity results. Practical implications The attempt can potentially meet the demand for flexible tubular scaffolds that ease the concerns such as availability of suitable organ donors. Originality/value 3D printing over accurate predefined templates to fabricate customized grafts gives novelty to the present method. Various customized scaffolds were compared with conventional cylindrical scaffold in terms of flexibility.

Download Full-text