scholarly journals Aerodynamic characteristics of morphing wing with flexible leading-edge

2020 ◽  
Vol 33 (10) ◽  
pp. 2610-2619 ◽  
Author(s):  
Zi KAN ◽  
Daochun LI ◽  
Tong SHEN ◽  
Jinwu XIANG ◽  
Lu ZHANG
Keyword(s):  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Morphing Wing

scholarly journals Analisis karakteristik aerodinamika telescopic wing dengan konfigurasi sayap flying wing dan glider menggunakan metode pendekatan simulasi CFD

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Azhim Asyratul Azmi ◽  
Satriawan Dini Hariyanto ◽  
Arif Hidayat
Keyword(s):  
Cfd Simulation ◽  
Fluid Dynamic ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Morphing Wing ◽  
Aircraft Wing ◽  
High Lift ◽  
Tip Vortices ◽  
Wing Tip

A telescopic wing is a shape-changing method of the aircraft wing known as the morphing wing system. Wingspan extends capability on telescopic wing increasing the aspect ratio to get a high lift force. The telescopic wing on a flying wing configuration as an external wing and glider wing as an internal wing can be used to increase the coefficient lift (CL) when carrying out special missions. The aerodynamic characteristics using the Computational Fluid Dynamic (CFD) simulation approach is presented. For the 40% internal wingspan, the highest CL increment was 12.9% at a 10o angle of attack. For the 50% internal wingspan, the highest CL increment was 14.9% at a 10o angle of attack. on the 40% internal wing, the highest coefficient drag (CD) increment was 4.7%, and the largest CD increment on 50% internal was 9.5% at the angle of attack of 20o. The pressure distribution along the internal wingspan was uneven from an angle of attack of 15o due to the wing tip vortices of the external wing. Streamline pattern shown a bubble separation from the leading edge at an internal wing root by external wing tip vortices.Keywords: Morphing wing, telescopic wing, flying wing, glider

Numerical study of geometric morphing wings of the 1303 UCAV

2021 ◽  
pp. 1-17
Author(s):  
B. Nugroho ◽  
J. Brett ◽  
B.T. Bleckly ◽  
R.C. Chin
Keyword(s):  
Flight Control ◽  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Morphing Wing ◽  
Rolling Moment ◽  
Wide Range ◽  
Morphing Wings ◽  
Wing Geometry ◽  
Lift And Drag ◽  
Wing Morphing

ABSTRACT Unmanned Combat Aerial Vehicles (UCAVs) are believed by many to be the future of aerial strike/reconnaissance capability. This belief led to the design of the UCAV 1303 by Boeing Phantom Works and the US Airforce Lab in the late 1990s. Because UCAV 1303 is expected to take on a wide range of mission roles that are risky for human pilots, it needs to be highly adaptable. Geometric morphing can provide such adaptability and allow the UCAV 1303 to optimise its physical feature mid-flight to increase the lift-to-drag ratio, manoeuvrability, cruise distance, flight control, etc. This capability is extremely beneficial since it will enable the UCAV to reconcile conflicting mission requirements (e.g. loiter and dash within the same mission). In this study, we conduct several modifications to the wing geometry of UCAV 1303 via Computational Fluid Dynamics (CFD) to analyse its aerodynamic characteristics produced by a range of different wing geometric morphs. Here we look into two specific geometric morphing wings: linear twists on one of the wings and linear twists at both wings (wash-in and washout). A baseline CFD of the UCAV 1303 without any wing morphing is validated against published wind tunnel data, before proceeding to simulate morphing wing configurations. The results show that geometric morphing wing influences the UCAV-1303 aerodynamic characteristics significantly, improving the coefficient of lift and drag, pitching moment and rolling moment.

Cavity for Flow Control and Performance Improvement of Airfoil

2021 ◽  
Author(s):  
Anand Verma ◽  
Bastav Borah ◽  
Vinayak Kulkarni
Keyword(s):  
Moving Boundary ◽  
Flow Analysis ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Suction Surface ◽  
Confined Spaces ◽  
Steady Simulation ◽  
And Performance ◽  
Lift And Drag ◽  
Fluid Flow Analysis

Abstract The fluid flow analysis over a cambered airfoil having three different cavity locations on the suction surface is reported in this paper. The Elliptical cavity is created at LE, MC, and TE along chordwise locations from the leading to trailing edge. In this regard, the steady simulation is carried out in the Fluent at Reynolds number of 105 based on their chord length. The lift and drag characteristics for clean and cavities airfoil are investigated at different angles of attack. For the clean airfoil, the stall point is observed at 18°. The presence of a cavity improves the stall and aerodynamic characteristics of airfoil. It has been seen that the lift and drag coefficients for pre-stalled or lower angles are nearly similar to clean and cavity at MC or TE positions. For the post-stall point, the improvement in the aerodynamic performance is seen for the cavity at MC or TE. The cavity placed at LE produces lower lift and higher drag characteristics against other configuration models. The overall cavity effect for the flow around the airfoil is that it creates vortices, thereby re-energizes the slower moving boundary layer and delays the flow separation in the downstream direction. The outcomes of this analysis are suggested that the cavity at a position before the mid chord from the leading edge does not improve the performance of the airfoil. Though vortex is formed in the confined spaces but it is unable to reattach the flow towards the downstream direction of an airfoil.

Large Eddy Simulation of Wake-Shear Layer Interactions Over a Multi-Element Aerofoil

2020 ◽  
Author(s):  
Souvik Naskar ◽  
S. Sarkar
Keyword(s):  
Large Eddy Simulation ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Simulation ◽  
Large Eddy

Abstract Modern commercial airliners use multi-element aerofoils to enhance take-off and landing performance. Further, multielement aerofoil configurations have been shown to improve the aerodynamic characteristics of wind turbines. In the present study, high resolution Large Eddy Simulation (LES) is used to explore the low Reynolds Number (Re = 0.832 × 104) aerodynamics of a 30P30N multi-element aerofoil at an angle of attack, α = 4°. In the present simulation, wake shed from a leading edge element or slat is found to interact with the separated shear layer developing over the suction surface of the main wing. High receptivity of shear layer via amplification of free-stream turbulence leads to rollup and breakdown, forming a large separation bubble. A transient growth of fluctuations is observed in the first half of the separation bubble, where levels of turbulence becomes maximum near the reattachment and then decay depicting saturation of turbulence. Results of the present LES are found to be in close agreement with the experiment depicting high vortical activity in the outer layer. Some features of the flow field here are similar to those occur due to interactions of passing wake and the separated boundary layer on the suction surface of high lift low pressure turbine blades.

scholarly journals A large-eddy simulation on a deep-stalled aerofoil with a wavy leading edge

2017 ◽  
Vol 813 ◽  
pp. 23-52 ◽  
Author(s):  
Rafael Pérez-Torró ◽  
Jae Wook Kim
Keyword(s):  
Vortex Shedding ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Domain Size ◽  
Aerodynamic Characteristics ◽  
Streamwise Vortices ◽  
Aerodynamic Forces ◽  
Laminar Separation ◽  
Eddy Simulation ◽  
Large Eddy

A numerical investigation on the stalled flow characteristics of a NACA0021 aerofoil with a sinusoidal wavy leading edge (WLE) at chord-based Reynolds number $Re_{\infty }=1.2\times 10^{5}$ and angle of attack $\unicode[STIX]{x1D6FC}=20^{\circ }$ is presented in this paper. It is observed that laminar separation bubbles (LSBs) form at the trough areas of the WLE in a collocated fashion rather than uniformly/periodically distributed over the span. It is found that the distribution of LSBs and their influence on the aerodynamic forces is strongly dependent on the spanwise domain size of the simulation, i.e. the wavenumber of the WLE used. The creation of a pair of counter-rotating streamwise vortices from the WLE and their evolution as an interface/buffer between the LSBs and the adjacent fully separated shear layers are discussed in detail. The current simulation results confirm that an increased lift and a decreased drag are achieved by using the WLEs compared to the straight leading edge (SLE) case, as observed in previous experiments. Additionally, the WLE cases exhibit a significantly reduced level of unsteady fluctuations in aerodynamic forces at the frequency of periodic vortex shedding. The beneficial aerodynamic characteristics of the WLE cases are attributed to the following three major events observed in the current simulations: (i) the appearance of a large low-pressure zone near the leading edge created by the LSBs; (ii) the reattachment of flow behind the LSBs resulting in a decreased volume of the rear wake; and, (iii) the deterioration of von-Kármán (periodic) vortex shedding due to the breakdown of spanwise coherent structures.

scholarly journals Design of compliant mechanism-based variable camber morphing wing with nonlinear large deformation

2019 ◽  
Vol 16 (6) ◽  
pp. 172988141988674 ◽  
Author(s):  
Yaqing Zhang ◽  
Wenjie Ge ◽  
Ziang Zhang ◽  
Xiaojuan Mo ◽  
Yonghong Zhang
Keyword(s):  
Large Deformation ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Flight Performance ◽  
Morphing Wing ◽  
Structure Topology ◽  
Trailing Edges ◽  
Morphing Wings

The morphing wing with large deformation can benefit its flight performance a lot in different conditions. In this study, a variable camber morphing wing with compliant leading and trailing edges is designed by large-displacement compliant mechanisms. The compliant mechanisms are carried out by a hyperelastic structure topology optimization, based on a nonlinear meshless method. A laminated leading-edge skin is designed to fit the curvature changing phenomenon of the leading edge during deformation. A morphing wing demonstrator was manufactured to testify its deformation capability. Comparing to other variable camber morphing wings, the proposal can realize larger deflection of leading and trailing edges. The designed morphing wing shows great improvement in aerodynamic performance and enough strength to resist aerodynamic and structural loadings.

New combinational active control strategy for improving aerodynamic characteristics of airfoil and rotor

2019 ◽  
Vol 234 (4) ◽  
pp. 977-996
Author(s):  
Yi-yang Ma ◽  
Qi-jun Zhao ◽  
Guo-qing Zhao
Keyword(s):  
Flow Control ◽  
Control Strategy ◽  
Active Flow Control ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Synthetic Jet ◽  
Dynamic Stall ◽  
Trailing Edge ◽  
Trailing Edge Flap ◽  
Cfd Method

In order to improve the aerodynamic characteristics of rotor, a new active flow control strategy by combining a synthetic jet actuator and a variable droop leading-edge or a trailing-edge flap has been proposed. Their control effects are numerically investigated by computational fluid dynamics (CFD) method. The validated results indicate that variable droop leading-edge and synthetic jet can suppress the formation of dynamic stall vortex and delay flow separation over rotor airfoil. Compared with the baseline state, Cdmax and Cmmax are significantly reduced. Furthermore, parametric analyses on dynamic stall control of airfoil by the combinational method are conducted, and it indicates that the aerodynamic characteristics of the oscillating rotor airfoil can be significantly improved when the non-dimensional frequency ( k*) of variable droop leading-edge is about 1.0. At last, simulations are conducted for the flow control of rotor by the combinational method. The numerical results indicate that large droop angle of variable droop leading-edge can better reduce the torque coefficient of rotor and the trailing-edge flap has the capability of increasing the thrust of rotor. Also, the synthetic jet could further improve the aerodynamic characteristics of rotor.

Sign in / Sign up

Export Citation Format

Share Document