Effects of applying a Miller cycle with split injection on engine performance and knock resistance in a downsized gasoline engine

Fuel ◽  
2018 ◽  
Vol 214 ◽  
pp. 98-107 ◽  
Author(s):  
Haiqiao Wei ◽  
Aifang Shao ◽  
Jianxiong Hua ◽  
Lei Zhou ◽  
Dengquan Feng
Keyword(s):  
Gasoline Engine ◽  
Engine Performance ◽  
Miller Cycle ◽  
Split Injection

scholarly journals Numerical investigation of Miller cycle with EIVC and LIVC on a high compression ratio gasoline engine

2021 ◽  
Vol 104 (2) ◽  
pp. 003685042110236
Author(s):  
Jiangtao Xu ◽  
Tongjun Guo ◽  
Yong Feng ◽  
Mengxin Sun
Keyword(s):  
Compression Ratio ◽  
Gasoline Engine ◽  
Engine Performance ◽  
High Load ◽  
Total Power ◽  
Miller Cycle ◽  
Indicated Mean Effective Pressure ◽  
Working Cycle ◽  
Total Power Consumption ◽  
Engine Knock

Previous studies have shown that increase compression ratio (CR) is an effective way to improve thermal efficiency of gasoline engine without changing the mechanical structure and working cycle, however, it is limited by engine knock when increasing the intake boosting under high load operation. This study aimed to solve the knock problem of gasoline engine with higher CR by application of Miller cycle, which can be implemented by either early or late intake valve closing (EIVC or LIVC). Therefore, in this paper, based on the engine with CR of 13.5 and electromagnetic valves train (EMVT), a comparative study was carried out to investigate the effects of EIVC and LIVC on engine performance, by theoretical modeling and calculation. The results show that, at high load, EIVC strategy is more preferred than LIVC owing to its lower total power consumption, which can improve the indicated mean effective pressure (IMEP) by 0.0371 bar, while enhance turbulence intensity and improve combustion. And at part load, the advantage for EIVC declines gradually, nevertheless, it can still sensitively adjust the EGR rate and thus reduce NOx. This results of quantitative analysis about two Miller cycles can provide valuable reference for engine designers and researchers.

scholarly journals A Comparison of Ethanol, Methanol, and Butanol Blending with Gasoline and Its Effect on Engine Performance and Emissions Using Engine Simulation

Processes ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 1322
Author(s):  
Simeon Iliev
Keyword(s):  
Alternative Fuels ◽  
Fossil Fuels ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Engine Simulation ◽  
Engine Model ◽  
Fuel Blends ◽  
Performance And Emissions ◽  
Blended Fuels

Air pollution, especially in large cities around the world, is associated with serious problems both with people’s health and the environment. Over the past few years, there has been a particularly intensive demand for alternatives to fossil fuels, because when they are burned, substances that pollute the environment are released. In addition to the smoke from fuels burned for heating and harmful emissions that industrial installations release, the exhaust emissions of vehicles create a large share of the fossil fuel pollution. Alternative fuels, known as non-conventional and advanced fuels, are derived from resources other than fossil fuels. Because alcoholic fuels have several physical and propellant properties similar to those of gasoline, they can be considered as one of the alternative fuels. Alcoholic fuels or alcohol-blended fuels may be used in gasoline engines to reduce exhaust emissions. This study aimed to develop a gasoline engine model to predict the influence of different types of alcohol-blended fuels on performance and emissions. For the purpose of this study, the AVL Boost software was used to analyse characteristics of the gasoline engine when operating with different mixtures of ethanol, methanol, butanol, and gasoline (by volume). Results obtained from different fuel blends showed that when alcohol blends were used, brake power decreased and the brake specific fuel consumption increased compared to when using gasoline, and CO and HC concentrations decreased as the fuel blends percentage increased.

scholarly journals A Theoretical Study on the Thermodynamic Cycle of Concept Engine with Miller Cycle

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1051
Author(s):  
Jungmo Oh ◽  
Kichol Noh ◽  
Changhee Lee
Keyword(s):  
Compression Ratio ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Thermodynamic Cycle ◽  
Expansion Ratio ◽  
Boost Pressure ◽  
Miller Cycle ◽  
Compression Pressure ◽  
Air Mass ◽  
Atkinson Cycle

The Atkinson cycle, where expansion ratio is higher than the compression ratio, is one of the methods used to improve thermal efficiency of engines. Miller improved the Atkinson cycle by controlling the intake- or exhaust-valve closing timing, a technique which is called the Miller cycle. The Otto–Miller cycle can improve thermal efficiency and reduce NOx emission by reducing compression work; however, it must compensate for the compression pressure and maintain the intake air mass through an effective compression ratio or turbocharge. Hence, we performed thermodynamic cycle analysis with changes in the intake-valve closing timing for the Otto–Miller cycle and evaluated the engine performance and Miller timing through the resulting problems and solutions. When only the compression ratio was compensated, the theoretical thermal efficiency of the Otto–Miller cycle improved by approximately 18.8% compared to that of the Otto cycle. In terms of thermal efficiency, it is more advantageous to compensate only the compression ratio; however, when considering the output of the engine, it is advantageous to also compensate the boost pressure to maintain the intake air mass flow rate.

Economy and emission characteristics of the optimal dilution strategy in lean combustion based on GDI gasoline engine equipped with prechamber

2021 ◽  
Vol 13 (12) ◽  
pp. 168781402110381
Author(s):  
Li Wang ◽  
Zhaoming Huang ◽  
Wang Tao ◽  
Kai Shen ◽  
Weiguo Chen
Keyword(s):  
Fuel Economy ◽  
Gasoline Engine ◽  
Direct Injection ◽  
Engine Performance ◽  
Gasoline Direct Injection ◽  
Dilution Ratio ◽  
Lean Combustion ◽  
Excess Air ◽  
Combustion Phase ◽  
Hc Emissions

EGR and excess-air dilution have been investigated in a 1.5 L four cylinders gasoline direct injection (GDI) turbocharged engine equipped with prechamber. The influences of the two different dilution technologies on the engine performance are explored. The results show that at 2400 rpm and 12 bar, EGR dilution can adopt more aggressive ignition advanced angle to achieve optimal combustion phasing. However, excess-air dilution has greater fuel economy than that of EGR dilution owing to larger in-cylinder polytropic exponent. As for prechamber, when dilution ratio is greater than 37.1%, the combustion phase is advanced, resulting in fuel economy improving. Meanwhile, only when the dilution ratio is under 36.2%, the HC emissions of excess-air dilution are lower than the original engine. With the increase of dilution ratio, the CO emissions decrease continuously. The NOX emissions of both dilution technologies are 11% of those of the original engine. Excess-air dilution has better fuel economy and very low CO emissions. EGR dilution can effectively reduce NOX emissions, but increase HC emissions. Compared with spark plug ignition, the pre chamber ignition has lower HC, CO emissions, and higher NO emissions. At part load, the pre-chamber ignition reduces NOX emissions to 49 ppm.

Turbocharger-Design Effects on Gasoline-Engine Performance

2005 ◽  
Vol 127 (3) ◽  
pp. 525-530 ◽  
Author(s):  
Theodosios Korakianitis ◽  
T. Sadoi
Keyword(s):  
Steady Flow ◽  
Mass Flow ◽  
Gasoline Engine ◽  
Pressure Ratio ◽  
Engine Performance ◽  
Thermodynamic Cycle ◽  
Final Choice ◽  
Design Point ◽  
Theoretical Considerations ◽  
Flow Experiments

Specification of a turbocharger for a given engine involves matching the turbocharger performance characteristics with those of the piston engine. Theoretical considerations of matching turbocharger pressure ratio and mass flow with engine mass flow and power permits designers to approach a series of potential turbochargers suitable for the engine. Ultimately, the final choice among several candidate turbochargers is made by tests. In this paper two types of steady-flow experiments are used to match three different turbochargers to an automotive turbocharged-intercooled gasoline engine. The first set of tests measures the steady-flow performance of the compressors and turbines of the three turbochargers. The second set of tests measures the steady-flow design-point and off-design-point engine performance with each turbocharger. The test results show the design-point and off-design-point performance of the overall thermodynamic cycle, and this is used to identify which turbocharger is suitable for different types of engine duties.

Performance Analysis and Improvement Approach of HEV Extended Expansion Gasoline Engine

2011 ◽  
Vol 317-319 ◽  
pp. 1999-2006
Author(s):  
Yu Wan ◽  
Ai Min Du ◽  
Da Shao ◽  
Guo Qiang Li
Keyword(s):  
Mathematical Model ◽  
Performance Analysis ◽  
Fuel Consumption ◽  
Economic Performance ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Valve Train ◽  
Gasoline Engines ◽  
Simulation Results ◽  
Negative Impacts

According to the boost mathematical model verified by experiments, the valve train of traditional gasoline engine is optimized and improved to achieve extended expansion cycle. The simulation results of extended expansion gasoline engine shows that the extended expansion gasoline engine has a better economic performance, compared to traditional gasoline engines. The average brake special fuel consumption (BSFC) can reduce 22.78 g / kW•h by LIVC, but the negative impacts of extended expansion gasoline engine restrict the potential of extended expansion gasoline engine. This paper analyzes the extended expansion gasoline engine performance under the influence of LIVC, discusses the way to further improve extended expansion gasoline engine performance.

Sign in / Sign up

Export Citation Format

Share Document