Investigation on tensile behaviour of Al/Si3N4/sugarcane ash particles reinforced FSP composites

2021 ◽  
Author(s):  
T. Vennila ◽  
Raviteja Surakasi ◽  
K.S. Raghuram ◽  
G. Ravi ◽  
S. Madhavarao ◽  
...  
Keyword(s):  
Tensile Behaviour

Comparison of the viscoelastic penetration and tensile behaviour of poly(methyl acrylate) and poly(ethyl acrylate)

1979 ◽  
Vol 44 (6) ◽  
pp. 1942-1948 ◽  
Author(s):  
Jaroslav Hrouz ◽  
Michal Ilavský ◽  
Ivan Havlíček ◽  
Karel Dušek
Keyword(s):  
Methyl Acrylate ◽  
Poisson Ratio ◽  
Young Modulus ◽  
Ethyl Acrylate ◽  
Sample Volume ◽  
Viscoelastic Behaviour ◽  
Tensile Behaviour ◽  
Temperature Superposition ◽  
Main Transition

The viscoelastic penetration and tensile behaviour of poly(methyl acrylate) and poly(ethyl acrylate) in the main transition region have been investigated. It was found that the time-temperature superposition could be carried out in the case of the penetration viscoelastic behaviour; the temperature dependence of the penetration and tensile shift factors was the same. The superimposed curves of the penetration and Young modulus allowed us to calculate the dependence of the Poisson ratio and thus to characterize the change in sample volume with deformation. It was demonstrated that the penetration method of determination of the viscoelastic behaviour is equivalent to the tensile method.

Deformation Behaviour and Ultrafine Grained Structure Development in Steels with Different Carbon Content Subjected to Severe Plastic Deformation

2007 ◽  
Vol 345-346 ◽  
pp. 45-48 ◽  
Author(s):  
Jozef Zrník ◽  
Sergey V. Dobatkin ◽  
Ondrej Stejskal
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Work Hardening ◽  
Favourable Effect ◽  
Tensile Behaviour ◽  
Dislocation Network ◽  
Strength Increase ◽  
Subgrain Structure ◽  
Low Carbon ◽  
Channel Angle

The article focuses on the results from recent experimental of severe plastic deformation of low carbon (LC) steel and medium carbon (MC) steel performed at increased temperatures. The grain refinement of ferrite respectively ferrite-pearlite structure is described. While LC steel was deformed by ECAP die (ε = 3) with a channel angle φ = 90° the ECAP severe deformation of MC steel was conducted with die channel angle of 120° (ε = 2.6 - 4). The high straining in LC steel resulted in extensively elongated ferrite grains with dense dislocation network and randomly recovered and polygonized structure was observed. The small period of work hardening appeared at tensile deformation. On the other side, the warm ECAP deformation of MC steel in dependence of increased effective strain resulted in more progressive recovery process. In interior of the elongated ferrite grains the subgrain structure prevails with dislocation network. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrain and submicrocrystalline structure. The straining and moderate ECAP temperature caused the cementite lamellae fragmentation and spheroidzation as number of passes increased. The tensile behaviour of the both steels was characterized by strength increase however the absence of strain hardening was found at low carbon steel. The favourable effect of ferrite-pearlite structure modification due straining was reason for extended work hardening period observed at MC steel.

Studies on mechanical property and wear behaviour of AA7075 hybrid composites prepared by a conventional casting method

2021 ◽  
pp. 095440892110349
Author(s):  
V Vignesh Kumar ◽  
K Raja ◽  
T Ramkumar ◽  
M Selvakumar ◽  
TS Senthil Kumar
Keyword(s):  
Boron Nitride ◽  
Boron Carbide ◽  
Hybrid Composites ◽  
Stir Casting ◽  
Wear Behaviour ◽  
Tensile Behaviour ◽  
Wear Properties ◽  
Casting Technique ◽  
Reciprocating Wear ◽  
Sliding Distance

The research article addresses the reciprocating wear behaviour of hybrid AA7075 reinforced with boron carbide and boron nitride through a stir-casting technique. The experiment involved varying wt.% of the secondary particle boron carbide (3, 6 and 9) while boron nitride (3) was kept as constant. The hybrid composites were characterised using scanning electron microscopy coupled with energy dispersive spectroscopy. The hardness and tensile behaviour of the hybrid composites were evaluated. Reciprocating wear behaviour of the hybrid composites were examined using a tribometer by varying the wear parameters such as load and sliding distance. The results revealed that AA7075/6boron carbide/3boron nitride had better hardness, tensile and wear properties. The surface morphology of the wear samples was analysed using SEM.

scholarly journals Constitutive Models for the Tensile Behaviour of TRM Materials: Literature Review and Experimental Verification

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 700
Author(s):  
Maria Concetta Oddo ◽  
Giovanni Minafò ◽  
Lidia La Mendola
Keyword(s):  
State Of The Art ◽  
Constitutive Models ◽  
Stress Transfer ◽  
Theoretical Models ◽  
Tensile Tests ◽  
Analytical Models ◽  
Tensile Behaviour ◽  
Tensile Response ◽  
Textile Reinforced Mortar ◽  
Inorganic Matrix

In recent years, the scientific community has focused its interest on innovative inorganic matrix composite materials, namely TRM (Textile Reinforced Mortar). This class of materials satisfies the need of retrofitting existing masonry buildings, by keeping the compatibility with the substrate. Different recent studies were addressed to improve the knowledge on their mechanical behaviour and some theoretical models were proposed for predicting the tensile response of TRM strips. However, this task is complex due to the heterogeneity of the constituent materials and the stress transfer mechanism developed between matrix and fabric through the interface in the cracked stage. This paper presents a state-of-the-art review on the existing constitutive models for the tensile behavior of TRM composites. Literature experimental results of tensile tests on TRM coupons are presented and compared with the most relevant analytical models proposed until now. Finally, a new experimental study is presented and its results are used to further verify the reliability of the literature expressions.

Modeling the Tensile Behaviour of a SiC/SiC Composite by Master Curves

2000 ◽  
Author(s):  
J. Shi
Keyword(s):  
Master Curve ◽  
Ceramic Matrix Composites ◽  
Test Material ◽  
Tensile Behaviour ◽  
Matrix Composites ◽  
Test Results ◽  
Master Curves ◽  
The Past ◽  
Test Parameters ◽  
Tensile Data

Scatter in test results is common for relatively brittle materials such as ceramic matrix composites. The scatter may come from differences in material processing conditions, specimen machining/handling and from variations in test parameters for nominally the same test material. Large scatter in test results makes material modeling difficult. In the past, master curve concepts have been proposed to reduce scatter in tensile data and to interpret fatigue/creep results. In this paper, one such concept is examined in detail by applying it to the recent tensile test results of a SiC/SiC composite. It was found that the way to construct master curves did not apply to the CMC studied and thus a new master curve was developed to better represent the tensile data. In addition, the test data were analysed statistically based on the new master curve.

Numerical and Experimental Analysis of the Tensile and Bending Behaviour of CFRP Cables

2017 ◽  
Vol 25 (9) ◽  
pp. 643-650
Author(s):  
Eduardo Antonio Wink de Menezes ◽  
Laís Vasconcelos da Silva ◽  
Carlos Alberto Cimini Junior ◽  
Felipe Ferreira Luz ◽  
Sandro Campos Amico
Keyword(s):  
Analytical Model ◽  
Oil And Gas ◽  
Steel Wire ◽  
Small Diameter ◽  
Oil And Gas Industry ◽  
Small Radius ◽  
Tensile Behaviour ◽  
Specific Strength ◽  
Numerical Predictions ◽  
Bending Behaviour

Due to their high fatigue life, specific strength and specific stiffness in comparison with steel, carbon-fibre reinforced polymer (CFRP) cables have attracted the infrastructure industry interest in recent years, primarily for use as structural tendons. Particularly the oil and gas industry showed interest for application in offshore platform anchorage systems, because of their exceptional corrosion and creep/relaxation behaviour. In such applications, the cables need to be tensioned in service and to be bent around relatively small-diameter spools for transportation and maintenance. Therefore, their tensile and bending behaviour is a subject of great concern. The aim of this work was to perform a test program on 1 × 19 CFRP cables in two different situations: tensile loading and four-point bending loading. Finite element models were developed to simulate both conditions, including frictional contact between the cable wires. A simplified analytical model was also used to predict the cable behaviour in tension. Numerical predictions were compared to experimental data showing relatively good accuracy, unlike the verified analytical model. CFRP cables presented outstanding tensile behaviour, but bending over small radius spools could not reach the performance of steel wire ropes. Furthermore, simulation could only fairly predict bending below strains of μ1,000 μe for the external rods, beyond which the cable presented highly non-linear behaviour that could not be simulated by the numerical model.

Sign in / Sign up

Export Citation Format

Share Document