Voltage deviate-domino circuits for low power high-speed applications using prescient innovation model

2019 ◽  
Vol 71 ◽  
pp. 102878
Author(s):  
C. Arun Prasath ◽  
C. Gowri Shankar
Keyword(s):  
Low Power ◽  
High Speed ◽  
Innovation Model ◽  
Domino Circuits

A Novel Method to Control Leakage and Noise in Domino Circuit for Wide Fan-in OR Logic

2021 ◽  
pp. 2250055
Author(s):  
Ankur Kumar ◽  
R. K. Nagaria
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Noise Immunity ◽  
Cmos Technology ◽  
Threshold Current ◽  
Delay Condition ◽  
Noise Margin ◽  
Novel Method ◽  
Domino Circuits

This paper proposes a novel method to control leakage and noise in domino circuits for wide fan-in OR logic with low power consumption, low process variation, and higher noise margin under the similar delay condition. In the proposed method, output and dynamic nodes are isolated from the PDN (Pull-Down Network) to improve the noise immunity and reduce switching activity. Further, with the aid of a transistor in the stack, the sub-threshold current is reduced. Thus, the proposed domino is applicable for high-speed and low-power applications in deep sub-micro-range. Simulation results show that the proposed domino improves the noise immunity and figure of merit (FOM) by factors of 1.95 and 2.34, respectively, with respect to the conventional domino with a footer. Along with this improvement, 26% reduction is also observed in power consumption. The entire simulations for all the domino circuits are done at 45-nm CMOS technology by using SPECTRE simulator under the Cadence Virtuoso environment.

scholarly journals Noise measurement in high-speed domino pseudo-CMOS keeper

2018 ◽  
Vol 52 (1-2) ◽  
pp. 20-27
Author(s):  
R Jaikumar ◽  
P Poongodi
Keyword(s):  
Low Power ◽  
High Speed ◽  
Noise Immunity ◽  
Delay Reduction ◽  
Power Dynamic ◽  
Unity Noise Gain ◽  
Power Delay Product ◽  
The Cost ◽  
Domino Circuits ◽  
Or Gate

Noise immunity is the foremost issue in high-speed domino circuits. In general, better noise immunity is achieved at the cost of speed and power degradation. In this paper, pseudo-dynamic keeper design is proposed to reduce the delay and power with improved noise immunity for domino circuits. The proposed technique is able to achieve reduced delay, power consumption, and better noise immunity by using always ON keeper. The simulation results show that the proposed technique exhibits 41%, 39%, and 19% delay reduction when compared with the low power dynamic circuit for two-input OR gate, two-input EX-OR gate, and 4:1 multiplexer. The proposed logic also performs better as compared to a low power dynamic circuit with 24%, 21%, and 14% reduction in power-delay product for two-input OR gate, two-input EX-OR gate, and four input MUX, respectively. The unity noise gain is also improved as compared to all other existing methods.

HIGH SPEED AND LOW POWER 4*4 ARRAY MULTIPLIER DESIGN

2019 ◽  
Vol 7 (1) ◽  
pp. 24
Author(s):  
N. SURESH ◽  
K. S. SHAJI ◽  
KISHORE REDDY M. CHAITANYA ◽  
◽  
◽  
...  
Keyword(s):  
Low Power ◽  
High Speed ◽  
Array Multiplier

Design and Implementation of an Efficient Parallel LFSR Architecture for Wireless Communication Systems

2019 ◽  
Vol 14 ◽  
Author(s):  
A. Suresh Babu ◽  
B. Anand
Keyword(s):  
Wireless Communication ◽  
Power Consumption ◽  
Low Power ◽  
Communication Systems ◽  
High Speed ◽  
Design Tool ◽  
Shift Register ◽  
Linear Feedback ◽  
Wireless Communication Systems ◽  
Coverage Area

: A Linear Feedback Shift Register (LFSR) considers a linear function typically an XOR operation of the previous state as an input to the current state. This paper describes in detail the recent Wireless Communication Systems (WCS) and techniques related to LFSR. Cryptographic methods and reconfigurable computing are two different applications used in the proposed shift register with improved speed and decreased power consumption. Comparing with the existing individual applications, the proposed shift register obtained >15 to <=45% of decreased power consumption with 30% of reduced coverage area. Hence this proposed low power high speed LFSR design suits for various low power high speed applications, for example wireless communication. The entire design architecture is simulated and verified in VHDL language. To synthesis a standard cell library of 0.7um CMOS is used. A custom design tool has been developed for measuring the power. From the results, it is obtained that the cryptographic efficiency is improved regarding time and complexity comparing with the existing algorithms. Hence, the proposed LFSR architecture can be used for any wireless applications due to parallel processing, multiple access and cryptographic methods.

Low Power and High Speed Sequential Circuits Test Architecture

2019 ◽  
Vol 12 ◽  
Author(s):  
Ahmed K. Jameil ◽  
Yasir Amer Abbas ◽  
Saad Al-Azawi
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Test Generation ◽  
High Speed ◽  
Fir Filter ◽  
Sequential Circuits ◽  
Fir Filters ◽  
Design Verification ◽  
Sequential Circuit ◽  
Generation Algorithm

Background: The designed circuits are tested for faults detection in fabrication to determine which devices are defective. The design verification is performed to ensure that the circuit performs the required functions after manufacturing. Design verification is regarded as a test form in both sequential and combinational circuits. The analysis of sequential circuits test is more difficult than in the combinational circuit test. However, algorithms can be used to test any type of sequential circuit regardless of its composition. An important sequential circuit is the finite impulse response (FIR) filters that are widely used in digital signal processing applications. Objective: This paper presented a new design under test (DUT) algorithm for 4-and 8-tap FIR filters. Also, the FIR filter and the proposed DUT algorithm is implemented using field programmable gate arrays (FPGA). Method: The proposed test generation algorithm is implemented in VHDL using Xilinx ISE V14.5 design suite and verified by simulation. The test generation algorithm used FIR filtering redundant faults to obtain a set of target faults for DUT. The fault simulation is used in DUT to assess the benefit of test pattern in fault coverage. Results: The proposed technique provides average reductions of 20 % and 38.8 % in time delay with 57.39 % and 75 % reductions in power consumption and 28.89 % and 28.89 % slices reductions for 4- and 8-tap FIR filter, respectively compared to similar techniques. Conclusions: The results of implementation proved that a high speed and low power consumption design can be achieved. Further, the speed of the proposed architecture is faster than that of existing techniques.

Performance Analysis of Various Multipliers Using 8T-full Adder with 180nm Technology

2020 ◽  
Vol 13 (6) ◽  
pp. 864-870
Author(s):  
Sai Venkatramana Prasada G.S ◽  
G. Seshikala ◽  
S. Niranjana
Keyword(s):  
Low Power ◽  
Power Dissipation ◽  
High Speed ◽  
High Performance ◽  
Full Adder ◽  
Fundamental Operation ◽  
Wallace Tree ◽  
Power Delay Product ◽  
The Comparative Study ◽  
Wallace Tree Multiplier

Background: This paper presents the comparative study of power dissipation, delay and power delay product (PDP) of different full adders and multiplier designs. Methods: Full adder is the fundamental operation for any processors, DSP architectures and VLSI systems. Here ten different full adder structures were analyzed for their best performance using a Mentor Graphics tool with 180nm technology. Results: From the analysis result high performance full adder is extracted for further higher level designs. 8T full adder exhibits high speed, low power delay and low power delay product and hence it is considered to construct four different multiplier designs, such as Array multiplier, Baugh Wooley multiplier, Braun multiplier and Wallace Tree multiplier. These different structures of multipliers were designed using 8T full adder and simulated using Mentor Graphics tool in a constant W/L aspect ratio. Conclusion: From the analysis, it is concluded that Wallace Tree multiplier is the high speed multiplier but dissipates comparatively high power. Baugh Wooley multiplier dissipates less power but exhibits more time delay and low PDP.

Sign in / Sign up

Export Citation Format

Share Document