The formation mechanism of the chill fine-grain layer with high supersaturation and its influence on the mechanical properties of die casting Al-7Si-0.5Mg alloy

2021 ◽  
pp. 142544
Author(s):  
Guodong Niu ◽  
Jeff Wang ◽  
Jinping Li ◽  
Jinwen Ye ◽  
Jian Mao
Keyword(s):  
Mechanical Properties ◽  
Formation Mechanism ◽  
Die Casting ◽  
Fine Grain ◽  
High Supersaturation

Effects of bottom plate in friction stir welding of AA6061-T6

2020 ◽  
Vol 118 (1) ◽  
pp. 108
Author(s):  
M.A. Vinayagamoorthi ◽  
M. Prince ◽  
S. Balasubramanian
Keyword(s):  
Mechanical Properties ◽  
Axial Load ◽  
Weld Zone ◽  
Welding Process ◽  
Bottom Plate ◽  
Welding Parameters ◽  
Nugget Zone ◽  
Friction Stir ◽  
Weld Joints ◽  
Fine Grain

The effects of 40 mm width bottom plates on the microstructural modifications and the mechanical properties of a 6 mm thick FSW AA6061-T6 joint have been investigated. The bottom plates are placed partially at the weld zone to absorb and dissipate heat during the welding process. An axial load of 5 to 7 kN, a rotational speed of 500 rpm, and a welding speed of 50 mm/min are employed as welding parameters. The size of the nugget zone (NZ) and heat-affected zone (HAZ) in the weld joints obtained from AISI 1040 steel bottom plate is more significant than that of weld joints obtained using copper bottom plate due to lower thermal conductivity of steel. Also, the weld joints obtained using copper bottom plate have fine grain microstructure due to the dynamic recrystallization. The friction stir welded joints obtained with copper bottom plate have exhibited higher ductility of 8.9% and higher tensile strength of 172 MPa as compared to the joints obtained using a steel bottom plate.

scholarly journals Effect of Sm Doping on the Microstructure, Mechanical Properties and Shape Memory Effect of Cu-13.0Al-4.0Ni Alloy

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4007
Author(s):  
Qimeng Zhang ◽  
Bo Cui ◽  
Bin Sun ◽  
Xin Zhang ◽  
Zhizhong Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
Compressive Fracture ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Face Centered

The effects of rare earth element Sm on the microstructure, mechanical properties, and shape memory effect of the high temperature shape memory alloy, Cu-13.0Al-4.0Ni-xSm (x = 0, 0.2 and 0.5) (wt.%), are studied in this work. The results show that the Sm addition reduces the grain size of the Cu-13.0Al-4.0Ni alloy from millimeters to hundreds of microns. The microstructure of the Cu-13.0Al-4.0Ni-xSm alloys are composed of 18R and a face-centered cubic Sm-rich phase at room temperature. In addition, because the addition of the Sm element enhances the fine-grain strengthening effect, the mechanical properties and the shape memory effect of the Cu-13.0Al-4.0Ni alloy were greatly improved. When x = 0.5, the compressive fracture stress and the compressive fracture strain increased from 580 MPa, 10.5% to 1021 MPa, 14.8%, respectively. When the pre-strain is 10%, a reversible strain of 6.3% can be obtained for the Cu-13.0Al-4.0Ni-0.2Sm alloy.

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

2014 ◽  
Vol 602-603 ◽  
pp. 438-442
Author(s):  
Lei Yu ◽  
Jian Yang ◽  
Tai Qiu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Bending Strength ◽  
Coefficient Of Thermal Expansion ◽  
Raw Materials ◽  
Linear Increase ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Uniform Microstructure

Fully dense (ZrB2+ZrC)/Zr3[Al (Si)]4C6 composites with ZrB2 content varying from 0 to 15 vol.% and fixed ZrC content of 10 vol.% were successfully prepared by in situ hot-pressing in Ar atmosphere using ZrH2, Al, Si, C and B4C as raw materials. With the increase of ZrB2 content, both the bending strength and fracture toughness of the composites increase and then decrease. The synergistic action of ZrB2 and ZrC as reinforcements shows significant strengthening and toughing effect to the Zr3[Al (Si)]4C6 matrix. The composite with 10 vol.% ZrB2 shows the optimal mechanical properties: 516 MPa for bending strength and 6.52 MPa·m1/2 for fracture toughness. With the increase of ZrB2 content, the Vickers hardness of the composites shows a near-linear increase from 15.3 GPa to 16.7 GPa. The strengthening and toughening effect can be ascribed to the unique mechanical properties of ZrB2 and ZrC reinforcements, the differences in coefficient of thermal expansion and modulus between them and Zr3[Al (Si)]4C6 matrix, fine grain strengthening and uniform microstructure derived by the in situ synthesis reaction.

Microstructure Evolution and Mechanical Properties of Rheoformed YL112 Aluminum Alloy

2008 ◽  
Vol 141-143 ◽  
pp. 163-168 ◽  
Author(s):  
Xiang Jie Yang ◽  
Hong Min Guo
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Shape Factor ◽  
Die Casting ◽  
Equivalent Diameter ◽  
Uniform Microstructure ◽  
Casting Aluminum Alloy ◽  
Casting Aluminum ◽  
Semi Solid ◽  
Secondary Solidification

Rheo-die casting (RDC) based on LSPSF (low superheat pouring with a shear field) rheocasting process has been exploited. In case of secondary die casting aluminum alloy YL112, LSPSF allowed for preparation of sound semi-solid slurry in 15-20s that fully meet the production rate of HPDC, the primary α-Al exhibiting a mean equivalent diameter of 70 μm and shape factor of 0.93, without any entrapped eutectic. Compared to conventional HPDC, RDC improves microstructures in castings. Secondary solidification of semi-solid slurry takes place uniformly throughout the entire cavity, producing an extremely fine and uniform microstructure. The experimental results show the RDC 380 alloy has much improved integrity and mechanical properties, particularly elongation, and heat treatment can be used to enhance the mechanical properties.

Reference Dies for the Evaluation of Tensile Properties of Gravity Cast Al-Si Alloys: An Overview

2014 ◽  
Vol 794-796 ◽  
pp. 71-76 ◽  
Author(s):  
Anilchandra R. Adamane ◽  
Elena Fiorese ◽  
Giulio Timelli ◽  
Franco Bonollo ◽  
Lars Arnberg
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Scientific Literature ◽  
Die Casting ◽  
Al Alloy ◽  
Casting Defects ◽  
Automotive Components ◽  
Foundry Alloys ◽  
Alloy Castings ◽  
Gravity Cast

Aluminium-Silicon (Al-Si) alloys are the most extensively used Al foundry alloys and are widely used in gravity die-casting (GDC) of automotive components. Reference dies are used to characterize the tensile properties of the castings. Among the various die configurations, the ASTM B-108 (also called the Stahl Mold), and the AA Step Mold are most popular in the foundries. Several modifications to the standard dies have been suggested in the scientific literature to obtain better mechanical properties in minimizing casting defects. This work reviews the scientific literature on the effect of different reference dies on the porosity and tensile properties of the Al alloy castings.

Sign in / Sign up

Export Citation Format

Share Document