Efficacy of Double Manual Cleaning Versus Automated Cleaning for Removal of Biofilm of Hinged Surgical Instruments

2020 ◽  
Vol 41 (S1) ◽  
pp. s518-s519
Author(s):  
Dayane Costa ◽  
Roel Castillo ◽  
Lillian Kelly Lopes ◽  
Anaclara Tipple ◽  
Honghua Hu ◽  
...  

Objectives: To evaluate the efficacy of double manual cleaning (DMC) with enzymatic followed by alkaline detergent for removing biofilm on hinged surgical instruments compared to automated cleaning by the washer-disinfector. Methods: Biofilm of Staphylococcus aureus (ATCC 25923) was formed in vitro on hemostatic forceps (Fig. 1). Biofilm-covered forceps were rinsed in distilled water and subjected to one of the following cleaning regimes (n = 5 forceps each): Group 1 forceps were soaked in sterile water for 5 minutes. Group 2-DMC forceps were soaked in enzymatic detergent, brushed 5 times on each face, rinsed with filtrated water (0.2 µm), soaked in alkaline detergent, brushed 5 times each face, rinsed with filtrated water (0.2 µm), and dried with sterile cloth. For group 3-DMC plus hinge inner brushing (n = 5), the forceps were soaked in detergents and brushed as in group 2, including hinge inner brushing (2-mm lumen brush) (Fig. 1). In group 4 (automated cleaning in a washer/disinfector), forceps were prewashed, washed once, washed again, rinsed, thermally rinsed, and dried. After the treatments, forceps were evaluated for microbial load (counting of colony-forming units), residual protein (BCA protein assay kit), and biofilm (scanning electron microscopy). Results: There was no statistically significant differences between the microbial load and protein level contaminating the forceps subjected to DMC (group 2) and the positive control group. The DMC with hinge inner brushing group (group 3) and the automated cleaning group (group 4) demonstrated a significantly reduced microbial load: reduction averages of 2.8 log 10 (P = .038) and 7.6 log10 (P ≤ .001), respectively. The protein level remaining on the forceps also significantly decreased: 2.563 μg (P = .016) and 1,453 μg (P = .001), respectively, compared to the positive control group. There was no statistically significant difference between DMC with hinge inner brushing and automated cleaning (groups 3 and 4) for all of the tests performed. None of the cleaning methods completely removed biofilm and/or soil from the forceps hinge internal region (Fig. 1). Conclusions: Automated cleaning had the best efficacy for removing biofilm. However, DMC with hinge inner brushing was an acceptable alternative cleaning method for sterilizing service units with only manual cleaning available, as is the case in most low- and middle-income countries. Neither automated nor any manual cleaning regimes were able to completely remove biofilm and soil from the forceps hinged area, and the amount of protein left after automated and DMC plus hinge brushing was higher than the recommended. Cleaning is the most important step for the reprocessing of reusable medical devices; thus, efforts must be undertaken to improve cleaning in different social and economic realities and scenarios.Funding: This study was supported by Coordenação de Aperfeiçoamento de Pessoal de Nível Superior – CAPES.Disclosures: None

2018 ◽  
Vol 21 (1) ◽  
pp. 26 ◽  
Author(s):  
Hatice Miray Uyan ◽  
Keziban Olcay ◽  
Mutlu Özcan

<p><strong>Objective:</strong> This study was designed to evaluate postoperative pain after endodontic retreatment. <strong>Material and Methods:</strong> Asymptomatic, multi-rooted molar &amp; premolar teeth requiring retreatment with 2–5 mm periapical lesions were included. Seventy-eight teeth were randomly placed in four groups (n=20): single-visit (control, group 1), Ledermix (group 2), metronidazole, ciprofloxacin, minocycline mixture (group 3), calcium hydroxide (group 4). The postoperative pain was recorded using a VAS at 6, 12, 24, and 48 h after retreatment. Statistical evaluation was performed using Two-Way Repeated Measures ANOVA and Tukey test. <strong>Results:</strong> Mild pain occurred in 67.5%, moderate in 30%, and flare-ups in 2.5%, and there was a significant difference between the groups (p&lt;0.01). Significantly lower postoperative pain was observed in TAP and CaOH<sub>2 </sub>groups(p&lt;0.05). In the 6, 12, and 24 h intervals, there was a significant difference in the pain levels (p&lt;0.05). <strong>Conclusion:</strong> TAP and CaOH<sub>2</sub> are effective for reducing postoperative pain after retreatment.</p><p><strong>Keywords</strong></p><p>Intracanal medicaments; Multiple-visit; Postoperative pain; Retreatment; Single-visit.</p>


2021 ◽  
Vol 14 (4) ◽  
pp. 1508-1513
Author(s):  
Ibraheem F Alshiddi

In order to assess the influence of finishing and polishing on the surface brightness and color stability of the ceramic veneer, fifty specimens were fabricated with 10 mm diameter and 2 mm thickness using IPS E-Max Ceramic. After glazing, 10 specimens were untouched as control group, and the other 40 specimens were abraded using 125µm diamond bur to create surface roughness. Forty specimens were divided into four groups (n=10), in group 1: specimens were finished using diamond point, in group 2 specimens’ surface was polished with a polishing kit, Group 3: Each specimen surface was polished with the polishing kit as in protocol 2 and was polished a polishing past and group 4 Each specimen was glazed by heating at 621℃ for 3 minutes followed by a temperature increase of 83℃/min up to 918℃ for 30 seconds. Color measurement was performed using spectrophotometer. Color stability data were analyzed using two-way ANOVA and Tukey’s HSD test (α=0.05). For Ra values, paired-samples t-tests were used to analyze the data and compare groups. The change in L and E showed a significant difference among the study groups; (group 1, group 2, group 3 and group 4) with respect to three variables L, a and b. A significant difference was noted when compared each group with the control; however, only group 2 showed a significant difference from group 4; the remaining groups demonstrated similar findings for all three variables. The study displayed a significant impact of the finishing and polishing technique on the surface brightness and color stability of ceramic restoration. However, it was evident that combination of two or three polishing techniques which includes polish kit and glaze enhances the surface finish and adds color stability by alternating the yellow – blue axis (increase in b) and red- green axis (decrease in a).


Author(s):  
Mine ARGALI DENIZ ◽  
Hilal ER ULUBABA ◽  
M. Furkan ARPACI ◽  
Fatih CAVUS ◽  
Gokhan DEMIRTAS ◽  
...  

Objective: In this study, the effect of tracheal diverticula (TD) on chest anthropometry and its relation with chronic obstructive pulmonary disease (COPD) was evaluated. Method: Between January 2019 and March 2020, 995 patients who underwent chest CT were retrospectively analyzed and TD was detected in 31 cases. Group 1 is only TD, Group 2 is TD + COPD, Group 3 is only COPD, Group 4 is defined as control group. We measured the localization, size, the distance to carina and vocal cord of TDs. In all groups chest diameters at T4 and T9 levels were measured as transverse and vertical plans. Results: TDs detected mostly at the T2 and T3 levels. In Group 1 and Group 2, there was a statistically significant difference the distance to TD of vocal chords. A statistically significant difference was found between Group 1 and Group 3 only in the vertical diameter at the T4 and T9 levels. Conclusion: We observed that COPD effect TD location and also TD had opposite effect on anteroposteriorly increasing chest parameters in COPD. Precence of TD is essential on COPD patients about thorax anthropometry. Keywords: Tracheal diverticulum; antropometry; radiology; COPD; chest diameter


2019 ◽  
Vol 12 (02) ◽  
Author(s):  
Husnul Khatimah ◽  
Saifuddin Sirajuddin ◽  
Zainal Zainal

ABSTRACT In diabetics there is usually an increase in free fatty acids in the blood and increases the concentration of cholecerols and triglycerides, this condition is called diabetes dyshidemia. This study aimed to find out at the effect of bran milk treatment on the changes of the concetration of cholesterol and triglycerides in diabetetic white wistar rats. Conducted on May 15 until 15 August 2018. Experimental research pre-post test with control design. Subjects of twenty wistar white rats were made diabetic by injecting alloxan 140mg / kg. After being declared diabetic, the rats were divided into four groups, namely group 1 (negative control), group 2 (positive control), group 3 (bran milk 0.54g / 200 gr) and group 4 (bran milk 1.08g / 200gr). The intervention was given for fourteen days. The data analysis used the paired T-test to test the subject before and afterthe treatment and the One-Way ANOVA test was used to test the difference between the groups. The research results indicated that  the treatment with bran milk there were no significant differences in cholesterol and triglyceride concentrations in the four groups. But when viewed from changes before and after the intervention showed that group 4 (bran milk 1.08g / 200gr) decreased cholesterol concentration and in group 3 (bran milk 0.54g / 200gr) a decrease in triglycerides was better than group 1 (control negative) and group 2 (positive control). It was concluded that the administration of bran milk can reduce the concentration of cholesterol and triglycerides in wistar diabetic white rats.Keywords : Bran milk, Cholesterol, Triglycerides, Rats, Diabetic


2015 ◽  
Vol 63 (4) ◽  
pp. 426-431
Author(s):  
Ariani Rodrigues DIMER ◽  
Guilherme Anziliero AROSSI ◽  
Leonardo Haerter dos SANTOS ◽  
Diego Rafael KAPPAUN

Objective: To evaluate the influence of different additional polymerization methods on the microhardness of two direct composite resins. Methods: Direct Composite resins samples (Fill Magic and Opallis) and a Laboratory Composite Resin (Ceramage) were lightcured according to manufacturer instructions. Then, the direct resins were submitted to additional polymerization. Experimental groups were divided into (n = 5): group 1: Conventional Polymerization; group 2: Extra Light (80s); group 3: Autoclave; group 4: Laboratory Resin Ceramage. Vickers hardness test was carried out after a week of light-free storage in water, and results were subjected to ANOVA / Tukey statistical analysis. Results: Resin Lab Ceramage showed higher astatistically significant microhardness within all other resins in this study (p £ 0.05); Fill Magic showed no statistically significant difference between the groups tested compared to its control (p> 0.05); Opallis resin submitted to autoclave was the only method that showed a higher statistically significant difference compared to the control group (p £ 0.05). Conclusion: It concludes that hardness of a direct composite resin tested - Opallis - was increased by Autoclave post-cure polymerization, however, not enough to achieve the hardness of a laboratory composite. Furthermore, increasing lightcuring time does not produce a harder surface.


2007 ◽  
Vol 77 (5) ◽  
pp. 901-906 ◽  
Author(s):  
Tamer Turk ◽  
Selma Elekdag-Turk ◽  
Devrim Isci ◽  
Fethiye Cakmak ◽  
Nurhat Ozkalayci

Abstract Objective: To evaluate shear bond strengths (SBSs) of a self-etching primer (SEP) following saliva contamination at different stages of bonding at debond times of 5, 15, and 30 minutes and 24 hours. Materials and Methods: Two-hundred forty human premolars were divided into four groups: group 1, uncontaminated; group 2, saliva contamination after priming; group 3, saliva contamination before priming; and group 4, saliva contamination before and after priming. Four subgroups according to debond times of 5, 15, 30 minutes and 24 hours were composed. Metal brackets were bonded with an SEP (Transbond Plus) and light-cure adhesives paste (Transbond XT). SBS values and the adhesive remnants were determined. Results: The highest SBS was obtained at a debond time of 24 hours for the control group. This was significantly different from the other groups. SBSs at 5, 15, and 30 minutes showed no significant difference from each other in the control group (P &gt; .05). Lowest SBSs were obtained at a debond time of 5 minutes for groups 1, 2, 3, and 4 (8.38, 7.10, 7.06, and 6.26 MPa, respectively) and were not significantly different from each other (P &gt; .05). SBSs at 24 hours were not significantly different from each other for groups 2, 3, and 4 (P &gt; .05). Significant differences were found in the adhesive remnant (P &lt; .001). Conclusions: SEP (Transbond Plus) may produce clinically acceptable bracket bonding after 5, 15, and 30 minutes from time of placement on the teeth, even with light and heavy saliva contamination.


Author(s):  
R Piradhiba ◽  
Evan A Clement ◽  
Navaneetha Nambi ◽  
S Veerasankar ◽  
S Madhumitra ◽  
...  

Introduction: Orthodontic elastics are a very significant tool in orthodontics, as it is the most commonly used force delivering unit. Temperature plays a key role in the amount of force that elastics are able to produce. Hence, there is a need to evaluate the influence of storage temperature on the properties of orthodontic elastics before its clinical use. Aim: To evaluate the influence of different storage temperature of latex orthodontic elastics. Materials and Methods: This cross-sectional study was conducted at Sathyabama Dental College and Hospital, Chennai, in November 2019. Sample of 40 latex orthodontic elastics (TP Orthodontics, medium force, standard size of 3/16′′) were divided into four groups with 10 elastics each, based on their storage temperature and stored in closed plastic packages. Group 1 was kept as a Control group and Group 2, Group 3 and Group 4 were stored in three Incubators under the specified storage temperatures such as 26-28°C, 4-8°C, 37°C respectively. The elastics were stretched and their forces measured in six progressive increases of 100% of their inner diameter, starting at a level of 100% stretching, with the Universal Testing Machine, Instron. The samples were also tested for Maximum Stress (MPa), Maximum Force (N), Maximum Elongation (%) and Break Distance (mm). Data were analysed using Statistical Package for the Social Science (SPSS) software version 16.0, one-way Analysis of Variance (ANOVA) and post-hoc test. Results: On evaluating the stress at 100%, 200%, 300%, 400%, 500%, 600% of strain, there was no statistically significant difference between the groups. Maximum Stress MPa was found to be 24.12±3.32, 25.12±3.42, 23.3±3.41, 23.97±3.50 for group1, group 2, group 3 and group 4 respectively. Maximum Elongation (%) was found to be 1369.0±25.108, 1364.0±23.190, 1359.0±35.103, 1363.0±34.657 for group 1, group 2, group 3 and group 4, respectively. Break Distance (mm) was found to be 68.48±1.267, 68.28±1.267, 67.87±1.77 and 68.19±1.727 for group1, group 2, group 3 and group 4, respectively. And none of the parameters tested showed statistical significance between the four groups. Conclusion: Latex elastics may be stored under any of the conditions tested in the present study over a period of one month, since different storage temperatures over a period of one month did not interfere in their mechanical properties.


2019 ◽  
Vol 9 (1) ◽  
pp. 5
Author(s):  
Ruslan Effendy ◽  
Vita Ariesta ◽  
Widya Saraswati

Background: Calcium hydroxide has been known as the gold standard of pulp capping process, but still has some weaknesses such as a pH that is too high to be potentially toxic, resistant to certain bacteria, causing necrosis of the pulp, and causing a tunnel defect. This weakness causes researchers to look for alternative ingredients that have antibacterical properties that can be combined with calcium hydroxide. Propolis has antibacterial properties such as flavonoids, tannins, saponins, and terpenoids which can work as the best carrier that allows dissociation of ions from calcium hydroxide so the combination of both that has antibacterial power is expected to have an effective antibacterial potency against the number of bacterial colonization with mixed dentine carious. Aims: This study aims to determine the antibacterial potency produced by a combination of calcium hydroxide and propolis against mixed bacteria of carious dentine. Methods: The research was carried out using 4 treatment groups with each of 7 samples. Group I is a combination of calcium hydroxide and propolis with a ratio of 1: 1, group 2 with a ratio of 1: 1.5, group 3 with a ratio of 1: 2, and a positive control group. Each sample was put into a suspense of mixed bacteria of carious dentine, grown for 24 hours. Suspense is vortexed for 1 minute so the solution becomes homogeneous. Put 0.1 ml of suspended mixed bacteria of dentine carious from BHIB media, grown for 24 hours on MHA media and counted the number of colonies. Results: The highest number of colonies in the positive control group, then group 1, group 2, and the least number of colonies in group 3 with the most extract of propolis. Conclusion: The combination of calcium hydroxide and propolis with a ratio of 1: 2 has the best antibacterial power in inhibiting colonization of mixed bacteria of carious dentine.


1993 ◽  
Vol 21 (2) ◽  
pp. 201-203 ◽  
Author(s):  
M. M. McSwiney ◽  
G. P. Joshi ◽  
P. Kenny ◽  
S. M. McCarroll

In a double-blind, randomised controlled trial, we studied 40 patients who received one of four intra-articular injections at the end of arthroscopic surgery. Each group contained ten patients. The patients in Group 1 received normal saline 25 ml; those in Group 2 received bupivacaine 0.25% 25 ml; those in Group 3 received morphine 5 mg in normal saline 25 ml; and those in Group 4 received a combination of bupivacaine 0.5% 12.5 ml and 5 mg of morphine made up to 25 ml with normal saline to produce the same bupivacaine concentration as Group 2. At the time the patient awoke, and 30min, Ihr, Ihr 30min, 2hr, 4hr, 8hr, 12hr, and 24hr postoperatively, pain was assessed using a visual analogue scale. The need for supplementary analgesic agents in the first 24 hours was recorded. All pain scores were significantly lower (P< 0.05) in Groups 2, 3 and 4 compared with the control group with the exception of Group 2 at 24 hours. Pain scores were significantly lower (P<0.05) for Group 2 compared with Group 3 for the first 90 minutes postoperatively. At 4, 8, 12 and 24 hours postoperatively the pain scores were significantly lower (P<0.05%) for Group 3 compared with Group 2. Group 4 had the lowest pain scores over the recorded period compared with the other groups. The need for supplemental analgesia was significantly lower (P<0.05) in the treatment Groups 2, 3 and 4 compared to the control Group 1. There was no significant difference in supplemental analgesic requirements between Groups 2, 3 and 4. A combination of bupivacaine and morphine injected intra-articularly following arthroscopy provided superior analgesia compared with that achieved by either drug alone.


2007 ◽  
Vol 76 (2) ◽  
pp. 203-207 ◽  
Author(s):  
A. Kart ◽  
M. Karapehlivan ◽  
K. Yapar ◽  
M. Citil ◽  
A. Akpinar

The macrolide antibiotic tilmicosin is known to induce cardiotoxic effect when administered at large doses. In this work, the effects of tilmicosin were evaluated with respect to alterations in total sialic acid, malondialdehyde and glutathione content of the heart, liver, kidney and lung tissues after single subcutaneous injection of 75 mg/kg tilmicosin with or without L-carnitine (500 mg/kg for 5 days daily via s.c. route) in BALB/c mice. L-carnitine is a co-factor serving in the mitochondrial β-oxidation of long chain fatty acids, and it was reported to be protective in several types of toxicity cases probably via multi-factorial mechanisms. Twenty eight mice were divided into 4 groups including group 1 (control), group 2 (L-carnitine), group 3 (tilmicosin) and group 4 (tilmicosin plus L-carnitine). Following the administration of treatments, tissue samples were collected, and the samples were assayed for malondialdehyde, glutathione and total sialic acid content. Mice receiving tilmicosin treatment alone had significantly higher malondialdehyde and total sialic acid concentrations (except for MDA of lungs) but lower glutathione concentration in selected tissues compared to those of the control, group 2 (Carnitine only) and group 4 (L-carnitine plus tilmicosin) (p < 0.05). However, no significant difference was found associated with the assayed indicators between the control and mice treated with L-carnitine plus tilmicosin. These results suggest that tilmicosin may cause oxidative stress in the heart, liver, lung and kidneys, but the adverse effects could be attenuated by L-carnitine administration.


Sign in / Sign up

Export Citation Format

Share Document