The use of STEM microdiffraction for the study of misorientation between subgrains

1978 ◽  
Vol 36 (1) ◽  
pp. 622-623
Author(s):  
M. D. Ball ◽  
P. L. Morris
Keyword(s):  
Electron Probe ◽  
Spot Size ◽  
Operating Conditions ◽  
Subgrain Structure ◽  
Grain Development ◽  
Thin Region ◽  
Ni Alloy ◽  
20 Nm ◽  
The Relationship

While there have been studies of the relationship between misorientation in worked structures and the development of recrystallisation nuclei, most have lacked accuracy owing to the positional uncertainty of selected area diffraction. However the fine electron probe forming capability required for STEM operation enables diffraction information to be obtained from regions of the order of 20 nm or less in diameter. We have applied this technique to an examination of recrystallisation in situ, where the early stages of grain development are arrested by the presence of particles.The microdiffraction studies were carried out on specimens prepared from an Al-6% Ni alloy which had been given various rolling and annealing treatments. A JEOL JEM 100C/ASID-4D electron microscope was used in the STEM mode with the operating conditions such that the spot size was about 20 nm with a beam divergence of 10-3 rad.For each of the specimens studied, a suitably thin region with a typical subgrain structure was selected and photographed.

An Expanding Thermal Plasma for Deposition of a-Si:H

1995 ◽  
Vol 377 ◽  
Author(s):  
R. J. Severens ◽  
G. J. H. Brussaard ◽  
H. J. M. Verhoeven ◽  
M. C. M. Van de Sanden ◽  
D. C. Schram
Keyword(s):  
Hydrogen Content ◽  
Hydrogen Plasma ◽  
Hydrogen Abstraction ◽  
Dissociative Recombination ◽  
Operating Conditions ◽  
Refractive Indices ◽  
Hydrogenated Silicon ◽  
Amorphous Hydrogenated Silicon ◽  
20 Nm

ABSTRACTA remote argon/hydrogen plasma is used to deposit amorphous hydrogenated silicon. The plasma is generated in a DC thermal arc (typical operating conditions 0.5 bar, 5 kW) and expands into a low pressure chamber (20 Pa) thus creating a plasma jet with a typical flow velocity of 103 m/s. Pure silane is injected into the jet immediately after the nozzle, in a typical flow mixture of Ar:H2:SiH4=55:10:6 scc/s. The electron temperature in the jet is low (typ. 0.3 eV) : silane radicals are thought to be produced mainly by hydrogen abstraction, but also by a sequence of dissociative charge exchange and consecutive dissociative recombination. In-situ ellipsometry yields refractive indices of 3.6–4.2 at 632.8 nm and growth rates of 10–20 nm/s. FTIR analysis yields a hydrogen content of 9–25 at.% and refractive indices of 2.7–3.3 in the infrared. The SiH density decreases with increasing hydrogen content, whereas the SiH2 density increases. Above 11 at.%, the majority of hydrogen is bonded in the SiH2 configuration. The optical bandgap remains constant at approximately 1.72 eV. The photoconductivity is of the order 101–6 (Ωcm) 1–6 and the photoresponse 106.

Electron Probe Analysis of Muscle

1982 ◽  
Vol 40 ◽  
pp. 398-401
Author(s):  
A. V. Somlyo ◽  
H. Shuman ◽  
A. P. Somlyo
Keyword(s):  
Skeletal Muscle ◽  
Smooth Muscle ◽  
Sarcoplasmic Reticulum ◽  
Resting State ◽  
Binding Sites ◽  
Electron Probe ◽  
Frog Skeletal Muscle ◽  
Electron Probe Analysis ◽  
Probe Analysis

Electron probe analysis of frozen dried cryosections of frog skeletal muscle, rabbit vascular smooth muscle and of isolated, hyperpermeab1 e rabbit cardiac myocytes has been used to determine the composition of the cytoplasm and organelles in the resting state as well as during contraction. The concentration of elements within the organelles reflects the permeabilities of the organelle membranes to the cytoplasmic ions as well as binding sites. The measurements of [Ca] in the sarcoplasmic reticulum (SR) and mitochondria at rest and during contraction, have direct bearing on their role as release and/or storage sites for Ca in situ.

Cathodoluminescence of Catalyst Crystallites

1982 ◽  
Vol 40 ◽  
pp. 664-665
Author(s):  
E.D. Boyes ◽  
P.L. Gai ◽  
D.B. Darby ◽  
C. Warwick
Keyword(s):  
Defect Density ◽  
Chemical Properties ◽  
Operating Conditions ◽  
Semiconductor Materials ◽  
Environmental Cell ◽  
High Resolution Structure ◽  
Commercially Important ◽  
Crystallographic Defects ◽  
Resolution Structure

The extended crystallographic defects introduced into some oxide catalysts under operating conditions may be a consequence and accommodation of the changes produced by the catalytic activity, rather than always being the origin of the reactivity. Operation without such defects has been established for the commercially important tellurium molybdate system. in addition it is clear that the point defect density and the electronic structure can both have a significant influence on the chemical properties and hence on the effectiveness (activity and selectivity) of the material as a catalyst. SEM/probe techniques more commonly applied to semiconductor materials, have been investigated to supplement the information obtained from in-situ environmental cell HVEM, ultra-high resolution structure imaging and more conventional AEM and EPMA chemical microanalysis.

Profile Imaging of Silicon Surface Reconstructions

1985 ◽  
Vol 43 ◽  
pp. 262-263
Author(s):  
O.L. Krivanek ◽  
G.J. Wood
Keyword(s):  
Electron Microscopy ◽  
Surface Structure ◽  
Structure Determination ◽  
Silicon Surface ◽  
Good Resolution ◽  
Surface Reconstructions ◽  
Bulk Structure ◽  
Point To Point ◽  
The Relationship

Electron microscopy at 0.2nm point-to-point resolution, 10-10 torr specimei region vacuum and facilities for in-situ specimen cleaning presents intere; ing possibilities for surface structure determination. Three methods for examining the surfaces are available: reflection (REM), transmission (TEM) and profile imaging. Profile imaging is particularly useful because it giv good resolution perpendicular as well as parallel to the surface, and can therefore be used to determine the relationship between the surface and the bulk structure.

Application Of Electron Probe Analyses Of Minerals In Discussing The Relationship Between Ductile Deformation And Metamorphism

1990 ◽  
Vol 48 (2) ◽  
pp. 250-251
Author(s):  
Fan Guochuan ◽  
Sun Zhongshi
Keyword(s):  
Chemical Composition ◽  
Shear Deformation ◽  
Electron Probe ◽  
General Rule ◽  
Granulite Facies ◽  
Ductile Deformation ◽  
Higher Temperature ◽  
Ductile Shear ◽  
The Relationship ◽  
Ductile Shear Deformation

Under influence of ductile shear deformation, granulite facies mineral paragenesis underwent metamorphism and changes in chemical composition. The present paper discusses some changes in chemical composition of garnet in hypers thene_absent felsic gnesiss and of hypersthene in rock in early and late granulite facies undergone increasing ductile shear deformation .In garnet fetsic geniss, band structures were formed because of partial melting and resulted in zoning from massive⟶transitional⟶melanocrate zones in increasing deformed sequence. The electron-probe analyses for garnet in these zones are listed in table 1 . The Table shows that Mno, Cao contents in garnet decrease swiftly from slightly to intensely deformed zones.In slightly and moderately deformed zones, Mgo contents keep unchanged and Feo is slightly lower. In intensely deformed zone, Mgo contents increase, indicating a higher temperature. This is in accord with the general rule that Mgo contents in garnet increase with rising temperature.

A combined ultrastructural and gene molecular research for the relationship between human uterine cervical carcinoma and human papillomavirus

1990 ◽  
Vol 48 (3) ◽  
pp. 204-205
Author(s):  
Kun Lee ◽  
Jingyi Si ◽  
Ricai Han ◽  
Wei Zhang ◽  
Bingbing Tan ◽  
...  
Keyword(s):  
Cervical Cancer ◽  
Human Papillomavirus ◽  
Intraepithelial Neoplasia ◽  
Hpv Infection ◽  
Dot Blot ◽  
Homologous Sequences ◽  
Normal Cervical Epithelium ◽  
The Relationship ◽  
Chronic Cervicitis

There are more supports for the view that human papillomavirus (HPV) infection might be an etiological factor in the development of cervical cancer when the association of persistent condylomata is considered. Biopsies from 318 cases with squamous cell carcinoma of uterine cervix, 48 with cervical and vulvar condylomata, 14 with cervical intraepithelial neoplasia (CIN), 34 with chronic cervicitis and 24 normal cervical epithelium were collected from 5 geographic regions of China with different cervical cancer mortalities. All specimens were prepared for Dot blot, Southern blot and in situ DNA-DNA hybridizations by using HPV-11, 16, 18 DNA labelled with 32P and 3H as probes to detect viral homologous sequences in samples. Among them, 32 cases with cervical cancer, 27 with condyloma and 10 normal cervical epitheliums were randomly chosen for comparative EM observation. The results showed that: 1), 192 out of 318 (60.4%) cases of cervical cancer were positive for HPV-16 DNA probe (Table I)

In-Situ Observation of Clay Minerals Hydrated and Intercalated With Liquid Chemicals Using Film-Sealed Environmental Cell

1980 ◽  
Vol 38 ◽  
pp. 208-209 ◽  
Author(s):  
K. Fukushima ◽  
N. Kohyama ◽  
A. Fukami
Keyword(s):  
Carbon Film ◽  
Resolving Power ◽  
In Situ Observation ◽  
Interlayer Water ◽  
Saturated Water ◽  
Structure Changes ◽  
Environmental Cell ◽  
Gas Layer ◽  
20 Nm

A film-sealed high resolution environmental cell(E.C) for observing hydrated materials had been developed by us(l). Main specification of the E.C. is as follows: 1) Accelerated voltage; 100 kV. 2) Gas in the E.C.; saturated water vapour with carrier gas of 50 Torr. 3) Thickness of gas layer; 50 μm. 4) Sealing film; evaporated carbon film(20 nm thick) with plastic microgrid. 5) Resolving power; 1 nm. 6) Transmittance of electron beam; 60% at 100 kV. The E.C. had been successfully applied to the study of hydrated halloysite(2) (3). Kaolin minerals have no interlayer water and are basically non-expandable but form intercalation compounds with some specific chemicals such as hydrazine, formamide and etc. Because of these compounds being mostly changed in vacuum, we tried to reveal the structure changes between in wet air and in vacuum of kaolin minerals intercalated with hydrazine and of hydrated state of montmori1lonite using the E.C. developed by us.

A pilot web former designed to study retention-formation relationships

2010 ◽  
Vol 25 (2) ◽  
pp. 185-194
Author(s):  
Anna Svedberg ◽  
Tom Lindström
Keyword(s):  
Pilot Scale ◽  
Operating Conditions ◽  
Montmorillonite Clay ◽  
Speed Ratio ◽  
Good Reproducibility ◽  
Total Solids ◽  
Retention Aids ◽  
Solids Content ◽  
Relationship Of ◽  
The Relationship

Abstract A pilot-scale fourdrinier former has been developed for the purpose of investigating the relationship between retention and paper formation (features, retention aids, dosage points, etc.). The main objective of this publication was to present the R-F (Retention and formation)-machine and demonstrate some of its fields of applications. For a fine paper stock (90% hardwood and 10% softwood) with addition of 25% filler (based on total solids content), the relationship between retention and formation was investigated for a microparticulate retention aid (cationic polyacrylamide together with anionic montmorillonite clay). The retention-formation relationship of the retention aid system was investigated after choosing standardized machine operating conditions (e.g. the jet-to-wire speed ratio). As expected, the formation was impaired when the retention was increased. Since good reproducibility was attained, the R-F (Retention and formation)-machine was found to be a useful tool for studying the relationship between retention and paper formation.

scholarly journals Engine Malfunctioning Conditions Identification through Instantaneous Crankshaft Torque Measurement Analysis

2021 ◽  
Vol 11 (8) ◽  
pp. 3522
Author(s):  
Konstantinos-Marios Tsitsilonis ◽  
Gerasimos Theotokatos
Keyword(s):  
Operating Conditions ◽  
Cylinder Pressure ◽  
Dynamics Model ◽  
Engine Model ◽  
Measurement Analysis ◽  
Start Of Injection ◽  
Rate Of Heat Release ◽  
Relationship Of ◽  
Diagnostic Measurement ◽  
The Relationship

In this study a coupled thermodynamics and crankshaft dynamics model of a large two-stroke diesel engine was utilised, to map the relationship of the engine Instantaneous Crankshaft Torque (ICT) with the following frequently occurring malfunctioning conditions: (a) change in Start of Injection (SOI), (b) change in Rate of Heat Release (RHR), (c) change in scavenge air pressure, and (d) blowby. This was performed using frequency analysis on the engine ICT, which was obtained through a series of parametric runs of the coupled engine model, under the various malfunctioning and healthy operating conditions. This process demonstrated that engine ICT can be successfully utilised to identify the distinct effects of malfunctions (c) or (d), as they occur individually in any cylinder. Furthermore by using the same process, malfunctions (a) and (b) can be identified as they occur individually for any cylinder, however there is no distinct effect on the engine ICT among these malfunctions, since their effect on the in-cylinder pressure is similar. As a result, this study demonstrates the usefulness of the engine ICT as a non-intrusive diagnostic measurement, as well as the benefits of malfunctioning conditions mapping, which allows for quick and less resource intensive identification of engine malfunctions.

Sign in / Sign up

Export Citation Format

Share Document