On the early stages of localised atmospheric corrosion of magnesium–aluminium alloys

AbstractThe surface film on pure magnesium and two aluminium-containing magnesium alloys was characterised after 96 h at 95% RH and 22 °C. The concentration of CO2 was carefully controlled to be either 0 or 400 ppm. The exposed samples were investigated using X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and electron microscopy. The results showed that when the alloys were exposed to the CO2-containing environment, aluminium cations (Al3+) was incorporated into a layered surface film comprising a partially “hydrated” MgO layer followed by Mg(OH)2, and magnesium hydroxy carbonates. The results indicated that aluminium-containing magnesium alloys exhibited considerably less localised corrosion in humid air than pure magnesium. Localised corrosion in the materials under investigation was attributed to film thinning by a dissolution/precipitation mechanism.

Download Full-text

On the early stages of localised atmospheric corrosion of magnesium- aluminium alloys

10.1149/osf.io/43s57 ◽

2020 ◽

Author(s):

Mehrdad Shahabi-Navid ◽

Yu Cao ◽

Jan-Erik Svensson ◽

Antoine Allanore ◽

Nick Birbilis ◽

...

Keyword(s):

Electron Microscopy ◽

Fourier Transform ◽

Photoelectron Spectroscopy ◽

Aluminium Alloys ◽

Atmospheric Corrosion ◽

Surface Film ◽

X Ray Diffraction ◽

Precipitation Mechanism ◽

X Ray ◽

Film Thinning

The surface film on pure magnesium and two aluminium-containing magnesium alloys was characterised after 96 h at 95% RH and 22°C. The concentration of CO2 was carefully controlled to be either 0 or 400 ppm. The exposed samples were investigated using X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, X-ray diffraction and electron microscopy. The results showed that when the alloys were exposed to the CO2-contaning environment, alumina (Al3+) was incorporated into a layered surface film comprising a partially “hydrated” MgO layer followed by Mg(OH)2, and magnesium hydroxy carbonates. Localised corrosion was attributed to film thinning by a dissolution/precipitation mechanism.

Download Full-text

X-ray Photoelectron Spectroscopy (XPS) Investigation of the Surface Film on Magnesium Powders

Applied Spectroscopy ◽

10.1366/11-06372 ◽

2012 ◽

Vol 66 (5) ◽

pp. 510-518 ◽

Cited By ~ 7

Author(s):

Paul J. Burke ◽

Zeynel Bayindir ◽

Georges J. Kipouros

Keyword(s):

Surface Layer ◽

Photoelectron Spectroscopy ◽

Focused Ion Beam ◽

Surface Film ◽

Ion Beam ◽

Pure Magnesium ◽

Atmospheric Conditions ◽

Magnesium Powder ◽

X Ray ◽

Aerospace Applications

Magnesium (Mg) and its alloys are attractive for use in automotive and aerospace applications because of their low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. Powder metallurgy may be a suitable solution for forming near-net-shape parts. However, sintering pure magnesium presents difficulties due to surface film that forms on the magnesium powder particles. The present work investigates the composition of the surface film that forms on the surface of pure magnesium powders exposed to atmospheric conditions and on pure magnesium powders after compaction under uniaxial pressing at a pressure of 500 MPa and sintering under argon at 600 °C for 40 minutes. Initially, focused ion beam microscopy was utilized to determine the thickness of the surface layer of the magnesium powder and found it to be ∼10 nm. The X-ray photoelectron analysis of the green magnesium sample prior to sintering confirmed the presence of MgO, MgCO3·3H2O, and Mg(OH)2 in the surface layer of the powder with a core of pure magnesium. The outer portion of the surface layer was found to contain MgCO3·3H2O and Mg(OH)2, while the inner portion of the layer is primarily MgO. After sintering, the MgCO3·3H2O was found to be almost completely absent, and the amount of Mg(OH)2 was also decreased significantly. This is postulated to occur by decomposition of the compounds to MgO and gases during the high temperature of sintering. An increase in the MgO content after sintering supports this theory.

Download Full-text

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

MRS Proceedings ◽

10.1557/proc-780-y5.5 ◽

2003 ◽

Vol 780 ◽

Author(s):

C. Essary ◽

V. Craciun ◽

J. M. Howard ◽

R. K. Singh

Keyword(s):

Uv Radiation ◽

Photoelectron Spectroscopy ◽

Grazing Angle ◽

X Ray Diffraction ◽

Metal Thin Films ◽

X Ray ◽

Force Microscopy ◽

Si Substrates ◽

Atomic Force ◽

Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

Download Full-text

α-Cellulose Fibers of Paper-Waste Origin Surface-Modified with Fe3O4 and Thiolated-Chitosan for Efficacious Immobilization of Laccase

Polymers ◽

10.3390/polym13040581 ◽

2021 ◽

Vol 13 (4) ◽

pp. 581

Author(s):

Gajanan S. Ghodake ◽

Surendra K. Shinde ◽

Ganesh D. Saratale ◽

Rijuta G. Saratale ◽

Min Kim ◽

...

Keyword(s):

Enzyme Immobilization ◽

Photoelectron Spectroscopy ◽

Cellulose Fibers ◽

Relative Activity ◽

Significant Activity ◽

X Ray Diffraction ◽

X Ray ◽

Transmission Electron ◽

Laccase Immobilization ◽

Surface Modified

The utilization of waste-paper-biomass for extraction of important α-cellulose biopolymer, and modification of extracted α-cellulose for application in enzyme immobilization can be extremely vital for green circular bio-economy. Thus, in this study, α-cellulose fibers were super-magnetized (Fe3O4), grafted with chitosan (CTNs), and thiol (-SH) modified for laccase immobilization. The developed material was characterized by high-resolution transmission electron microscopy (HR-TEM), HR-TEM energy dispersive X-ray spectroscopy (HR-TEM-EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses. Laccase immobilized on α-Cellulose-Fe3O4-CTNs (α-Cellulose-Fe3O4-CTNs-Laccase) gave significant activity recovery (99.16%) and laccase loading potential (169.36 mg/g). The α-Cellulose-Fe3O4-CTNs-Laccase displayed excellent stabilities for temperature, pH, and storage time. The α-Cellulose-Fe3O4-CTNs-Laccase applied in repeated cycles shown remarkable consistency of activity retention for 10 cycles. After the 10th cycle, α-Cellulose-Fe3O4-CTNs possessed 80.65% relative activity. Furthermore, α-Cellulose-Fe3O4-CTNs-Laccase shown excellent degradation of pharmaceutical contaminant sulfamethoxazole (SMX). The SMX degradation by α-Cellulose-Fe3O4-CTNs-Laccase was found optimum at incubation time (20 h), pH (3), temperatures (30 °C), and shaking conditions (200 rpm). Finally, α-Cellulose-Fe3O4-CTNs-Laccase gave repeated degradation of SMX. Thus, this study presents a novel, waste-derived, highly capable, and super-magnetic nanocomposite for enzyme immobilization applications.

Download Full-text

Photocatalytic Reduction of CO2 to Methanol Using a Copper-Zirconia Imidazolate Framework

Catalysts ◽

10.3390/catal11030346 ◽

2021 ◽

Vol 11 (3) ◽

pp. 346

Author(s):

Sonam Goyal ◽

Maizatul Shima Shaharun ◽

Ganaga Suriya Jayabal ◽

Chong Fai Kait ◽

Bawadi Abdullah ◽

...

Keyword(s):

Photoelectron Spectroscopy ◽

Catalyst Support ◽

Oxidation Potential ◽

Molar Ratio ◽

X Ray Diffraction ◽

X Ray ◽

Molar Ratios ◽

Optimum Parameters ◽

Reduction Of Co2 ◽

Enhanced Yield

A set of novel photocatalysts, i.e., copper-zirconia imidazolate (CuZrIm) frameworks, were synthesized using different zirconia molar ratios (i.e., 0.5, 1, and 1.5 mmol). The photoreduction process of CO2 to methanol in a continuous-flow stirred photoreactor at pressure and temperature of 1 atm and 25 °C, respectively, was studied. The physicochemical properties of the synthesized catalysts were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectroscopy. The highest methanol activity of 818.59 µmol/L.g was recorded when the CuZrIm1 catalyst with Cu/Zr/Im/NH4OH molar ratio of 2:1:4:2 (mmol/mmol/mmol/M) was employed. The enhanced yield is attributed to the presence of Cu2+ oxidation state and the uniformly dispersed active metals. The response surface methodology (RSM) was used to optimize the reaction parameters. The predicted results agreed well with the experimental ones with the correlation coefficient (R2) of 0.99. The optimization results showed that the highest methanol activity of 1054 µmol/L.g was recorded when the optimum parameters were employed, i.e., stirring rate (540 rpm), intensity of light (275 W/m2) and photocatalyst loading (1.3 g/L). The redox potential value for the CuZrIm1 shows that the reduction potential is −1.70 V and the oxidation potential is +1.28 V for the photoreduction of CO2 to methanol. The current work has established the potential utilization of the imidazolate framework as catalyst support for the photoreduction of CO2 to methanol.

Download Full-text

Study on the Electrical, Structural, Chemical and Optical Properties of PVD Ta(N) Films Deposited with Different N2 Flow Rates

Coatings ◽

10.3390/coatings11080937 ◽

2021 ◽

Vol 11 (8) ◽

pp. 937

Author(s):

Yingying Hu ◽

Md Rasadujjaman ◽

Yanrong Wang ◽

Jing Zhang ◽

Jiang Yan ◽

...

Keyword(s):

Crystal Structure ◽

Optical Properties ◽

Photoelectron Spectroscopy ◽

Crystal Size ◽

Silicon Substrates ◽

X Ray Diffraction ◽

Dc Magnetron Sputtering ◽

Flow Rates ◽

X Ray ◽

N2 Flow Rate

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with different N2 flow rates of 0, 12, 17, 25, 38, and 58 sccm. The effects of N2 flow rate on the electrical properties, crystal structure, elemental composition, and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of N2 flows. Furthermore, as resistivity increases, the crystal size decreases, the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta3N5(130, 040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N2 flow rates, depending on the crystal size and crystal phase structure.

Download Full-text

Optical, XPS and XRD Studies of Semiconducting Copper Sulfide Layers on a Polyamide Film

International Journal of Photoenergy ◽

10.1155/2009/304308 ◽

2009 ◽

Vol 2009 ◽

pp. 1-8 ◽

Cited By ~ 69

Author(s):

Valentina Krylova ◽

Mindaugas Andrulevičius

Keyword(s):

Photoelectron Spectroscopy ◽

Copper Sulfide ◽

Diffusion Method ◽

X Ray Diffraction ◽

Xps Spectra ◽

X Ray ◽

Xrd Studies ◽

Polyamide Film ◽

Indirect Band Gap ◽

Xrd Method

Copper sulfide layers were formed on polyamide PA 6 surface using the sorption-diffusion method. Polymer samples were immersed for 4 and 5 h in 0.15 mol⋅ solutions and acidified with HCl (0.1 mol⋅) at . After washing and drying, the samples were treated with Cu(I) salt solution. The samples were studied by UV/VIS, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) methods. All methods confirmed that on the surface of the polyamide film a layer of copper sulfide was formed. The copper sulfide layers are indirect band-gap semiconductors. The values of are 1.25 and 1.3 eV for 4 h and 5 h sulfured PA 6 respectively. Copper XPS spectra analyses showed Cu(I) bonds only in deeper layers of the formed film, while in sulfur XPS S 2p spectra dominating sulfide bonds were found after cleaning the surface with ions. It has been established by the XRD method that, beside , the layer contains as well. For PA 6 initially sulfured 4 h, grain size forchalcocite, , was nm and fordjurleite, , it was 54.17 nm. The sheet resistance of the obtained layer varies from 6300 to 102 .

Download Full-text

Biodiesel Production on Monometallic Pt, Pd, Ru, and Ag Catalysts Supported on Natural Zeolite

Materials ◽

10.3390/ma14010048 ◽

2020 ◽

Vol 14 (1) ◽

pp. 48

Author(s):

Pawel Mierczynski ◽

Magdalena Mosińska ◽

Lukasz Szkudlarek ◽

Karolina Chalupka ◽

Misa Tatsuzawa ◽

...

Keyword(s):

Photoelectron Spectroscopy ◽

Natural Zeolite ◽

Noble Metals ◽

Methyl Esters ◽

Physicochemical Characteristics ◽

Biodiesel Production ◽

X Ray Diffraction ◽

X Ray ◽

Yield Values ◽

Temperature Programmed

Biodiesel production from rapeseed oil and methanol via transesterification reaction facilitated by various monometallic catalyst supported on natural zeolite (NZ) was investigated. The physicochemical characteristics of the synthesized catalysts were studied by X-ray diffraction (XRD), Brunauer–Emmett–Teller method (BET), temperature-programmed-reduction in hydrogen (H2-TPR), temperature-programmed-desorption of ammonia (NH3-TPD), Scanning Electron Microscope equipped with EDX detector (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) methods. The highest activity and methyl ester yields were obtained for the Pt/NZ catalyst. This catalyst showed the highest triglycerides conversion of 98.9% and fatty acids methyl esters yields of 94.6%. The activity results also confirmed the high activity of the carrier material (NZ) itself in the investigated reaction. Support material exhibited 90.5% of TG conversion and the Fatty Acid Methyl Esters yield (FAME) of 67.2%. Introduction of noble metals improves the TG conversion and FAME yield values. Increasing of the metal loading from 0.5 to 2 wt.% improves the reactivity properties of the investigated catalysts.

Download Full-text

Impact of high temperatures on aluminoceladonite studied by Mössbauer, Raman, X-ray diffraction and X-ray photoelectron spectroscopy

Mineralogy and Petrology ◽

10.1007/s00710-021-00753-z ◽

2021 ◽

Author(s):

Mariola Kądziołka-Gaweł ◽

Maria Czaja ◽

Mateusz Dulski ◽

Tomasz Krzykawski ◽

Magdalena Szubka

Keyword(s):

Photoelectron Spectroscopy ◽

Integral Intensity ◽

Photoelectron Spectra ◽

X Ray Diffraction ◽

Structural Reorganization ◽

Oh Groups ◽

X Ray ◽

Al Content ◽

Integral Intensity Ratio ◽

Higher Temperature

AbstractMössbauer, Raman, X-ray diffraction and X-ray photoelectron spectroscopies were used to examine the effects of temperature on the structure of two aluminoceladonite samples. The process of oxidation of Fe2+ to Fe3+ ions started at about 350 °C for the sample richer in Al and at 300 °C for the sample somewhat lower Al-content. Mössbauer results show that this process may be associated with dehydroxylation or even initiate it. The first stage of dehydroxylation takes place at a temperature > 350 °C when the adjacent OH groups are replaced with a single residual oxygen atom. Up to ~500 °C, Fe ions do not migrate from cis-octahedra to trans-octahedra sites, but the coordination number of polyhedra changes from six to five. This temperature can be treated as the second stage of dehydroxylation. The temperature dependence on the integral intensity ratio between bands centered at ~590 and 705 cm−1 (I590/I705) clearly reflects the temperature at which six-coordinated polyhedra are transformed into five-coordinated polyhedra. X-ray photoelectron spectra obtained in the region of the Si2p, Al2p, Fe2p, K2p and O1s core levels, highlighted a route to identify the position of Si, Al, K and Fe cations in a structure of layered silicates with temperature. All the measurements show that the sample with a higher aluminum content and a lower iron content in octahedral sites starts to undergo a structural reorganization at a relatively higher temperature than the less aluminum-rich sample does. This suggests that iron may perform an important role in the initiation of the dehydroxylation of aluminoceladonites.

Download Full-text

Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽

10.3390/polym13040558 ◽

2021 ◽

Vol 13 (4) ◽

pp. 558

Author(s):

Wenhui Zhu ◽

Caiyun Zhang ◽

Yali Chen ◽

Qiliang Deng

Keyword(s):

Methylene Blue ◽

Photoelectron Spectroscopy ◽

Room Temperature ◽

Degradation Rate ◽

Model Compound ◽

Vibrating Sample Magnetometer ◽

Simulated Sunlight ◽

X Ray Diffraction ◽

X Ray ◽

Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

Download Full-text