scholarly journals Removal of diclofenac from aqueous solutions by adsorption on thermo-plasma expanded graphite

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Marco Cuccarese ◽  
Sergio Brutti ◽  
Angela De Bonis ◽  
Roberto Teghil ◽  
Ignazio Marcello Mancini ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Expanded Graphite ◽  
X Ray Diffraction ◽  
Multiplicative Inverse ◽  
Adsorbent Regeneration ◽  
Pseudo Second Order ◽  
Crystallite Dimension ◽  
Solvent Washing ◽  
Graphitic Material ◽  
Best Fit

AbstractThe adsorption of diclofenac on thermo-plasma expanded graphite (a commercial product) from water solutions was investigated. The adsorbent material was characterized by SEM, TEM, BET, Raman and X-ray diffraction analyses. Typical diffractogram and Raman spectrum of graphitic material, dimension of 24.02 nm as crystallite dimension and a surface area of 47 m2 g−1 were obtained. The effect of pH on the adsorption capacity was evaluated in the range 1–7 and the adsorption mechanism was described by kinetic and isothermal studies. Pseudo-second order and Dubinin–Radushkevich models agreed with theoretical values of adsorption capacity (i.e. 400 and 433 mg g−1, respectively) and resulted to be the best fit for kinetics and isothermal experimental data. The thermodynamics of the process was evaluated by plotting the adsorption capacity/concentration ratio at the equilibrium as a function of different values of the multiplicative inverse of temperature. Moreover, the adsorbent regeneration was also investigated, comparing two different remediation techniques. Solvent washing performed with NaOH 0.2 M and thermo-treatment carried out by heating in an oven at 105 °C for 2 h and then at 200 °C for 4 h. The thermo-treatment was the best technique to regenerate the adsorbent, ensuring same performance after 4 cycles of use and regeneration.

scholarly journals Preparation, characterization and application of the nanocomposite PCL-PEG-PCL / Bentonite-TBHSA to the removal of methylene blue (MB) dye: Adsorption, Kinetics, and Isotherm studies

2021 ◽  
Author(s):  
Zohra Draoua ◽  
Amine Harrane ◽  
Mehdi Adjdir
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Dye Adsorption ◽  
Second Order ◽  
X Ray Diffraction ◽  
Optimal Value ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Adsorption Kinetics And Isotherm ◽  
Best Fit

Abstract This study focuses on the synthesis, characterization, and application of amphiphilic PCL-PEG-PCL/Bentonite-TBHSA (A2). The prepared of A2 nanocomposite was prepared from Algerian Bentonite modified by the intercalation of tetrabutylammonium hydrogen sulfate (TBHSA) (A1), were characterized by different techniques including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction(XRD), (TEM),(DSC) and thermogravimetric analysis (TGA ). The removal efficiency of of methylene blue, from aqueous solutions. The effects of the initial pH of a solution, contact time, and nanocomposite mass on the adsorption efficiency were investigated. Pseudo-first/second-order isotherms were applied to determine the efficiency of nanocomposite solid. The experimental data fitted well with the pseudo-second-order model for MB dye adsorption. The mass of nanocomposite increased, the adsorption capacity of dye increases to reach an optimal value at 0.13 g of adsorbent in pH = 6.8. The Langmuir isotherm exhibited the best fit, with an adsorption capacity equal to 600 mg/g .

Competitive Biosorption of Pb(II) and Cu(II) by Functionalised Micropogonias undulates Scales

2020 ◽  
Vol 13 ◽  
Author(s):  
Joshua O. Ighalo ◽  
Ibrahim O. Tijani ◽  
Oluwaseun J. Ajala ◽  
Fisayo O. Ayandele ◽  
Omodele A. Eletta ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Fish Scales ◽  
Wet Impregnation ◽  
Monolayer Adsorption ◽  
Competitive Biosorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Best Fit

Background: Modified bio-based adsorbents from plant sources can be used for pollution remediation by adsorption due to their low cost and availability in large quantities. Objective: In this study, the competitive biosorption of Pb(II) and Cu(II) by Micropogonias undulates functionalised fish scales (FFS) was conducted. The functionalisation was done by wet impregnation with Fe2+. Method: The biosorbent was characterised by Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy with Energy-Dispersive X-ray Spectroscopy (SEM-EDS) and Branueur–Emmett–Teller (BET) analyses. Results: The major constituents in the FFS were calcium and phosphorus from the collagen and apatite on the scales. Optimum removal efficiency for both metals was >99% at 10 g/l dosage. It was observed that the Langmuir isotherm model and the pseudo second order kinetics model were the best fit for the experimental data. The monolayer adsorption capacity of FFS for Pb(II) and Cu(II) was observed to be 96.15 mg/g and 100 mg/g respectively. Conclusion: The study revealed that the competitive biosorption of heavy metals can be achieved (at a good adsorption capacity) using functionalised Micropogonias undulates fish scales.

scholarly journals Kinetic Study of the Bioadsorption of Methylene Blue on the Surface of the Biomass Obtained from the Algae D. antarctica

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Jhonatan R. Guarín ◽  
Juan Carlos Moreno-Pirajan ◽  
Liliana Giraldo
Keyword(s):  
Methylene Blue ◽  
Kinetic Study ◽  
Adsorption Capacity ◽  
Scientific Community ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Total Elimination ◽  
Purification Of Water

Currently, there is a great pollution of water by the dyes; due to this, several studies have been carried out to remove these compounds. However, the total elimination of these pollutants from the aquatic effluents has represented a great challenge for the scientific community, for which it is necessary to carry out investigations that allow the purification of water. In this work, we studied the bioadsorption of methylene blue on the surface of the biomass obtained from the algae D. antarctica. This material was characterized by SEM and FTIR. To the data obtained in the biosorption experiments, different models of biosorption and kinetics were applied, finding that the best fit to the obtained data is given by applying the pseudo-second-order models and the Toth model, respectively. It was also determined that the maximum adsorption capacity of MB on the surface of the biomass is 702.9 mg/g, which shows that this material has great properties as a bioadsorbent.

scholarly journals Adsorption of strontium on different sodium-enriched bentonites

2017 ◽  
Vol 82 (4) ◽  
pp. 449-463 ◽  
Author(s):  
Sanja Marinovic ◽  
Marija Ajdukovic ◽  
Natasa Jovic-Jovicic ◽  
Tihana Mudrinic ◽  
Bojana Nedic-Vasiljevic ◽  
...  
Keyword(s):  
Cation Exchange ◽  
Adsorption Capacity ◽  
Textural Properties ◽  
X Ray Diffraction ◽  
Order Model ◽  
Surface Areas ◽  
Alkaline Conditions ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ph Range

Bentonites from three different deposits (Wyoming, TX, USA and Bogovina, Serbia) with similar cation exchange capacities were sodium enriched and tested as adsorbents for Sr2+ in aqueous solutions. X-Ray diffraction analysis confirmed successful Na-exchange. The textural properties of the bentonite samples were determined using low-temperature the nitrogen physisorption method. Significant differences in the textural properties between the different sodium enriched bentonites were found. Adsorption was investigated with respect to adsorbent dosage, pH, contact time and the initial concentration of Sr2+. The adsorption capacity increased with pH. In the pH range from 4.0?8.5, the amount of adsorbed Sr2+ was almost constant but 2?3 times smaller than at pH ?11. Further experiments were performed at the unadjusted pH since extreme alkaline conditions are environmentally hostile and inapplicable in real systems. The adsorption capacity of all the investigated adsorbents toward Sr2+ was similar under the investigated conditions, regardless of significant differences in the specific surface areas. It was shown and confirmed by the Dubinin?Radushkevich model that the cation exchange mechanism was the dominant mechanism of Sr2+ adsorption. Their developed microporous structures contributed to the Sr2+ adsorption process. The adsorption kinetics obeyed the pseudo-second-order model. The isotherm data were best fitted with the Langmuir isotherm model.

scholarly journals Chitosan Grafted with Biobased 5-Hydroxymethyl-Furfural as Adsorbent for Copper and Cadmium Ions Removal

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1173 ◽  
Author(s):  
Mariza Mone ◽  
Dimitra A. Lambropoulou ◽  
Dimitrios N. Bikiaris ◽  
George Kyzas
Keyword(s):  
Adsorption Capacity ◽  
Significant Loss ◽  
X Ray Diffraction ◽  
Freundlich Model ◽  
Hydroxymethyl Furfural ◽  
Before And After ◽  
Equilibrium Data ◽  
Best Fitting ◽  
Pseudo Second Order ◽  
Grafting From

This work investigates the application of 5-hydroxymethyl-furfural (HMF) as a grafting agent to chitosan (CS). The material produced was further modified by cross-linking. Three different derivatives were tested with molecular ratios CS/HMF of 1:1 (CS-HMF1), 2:1 (CS-HMF2) and 10:1 mol/mol (CS-HMF3)) to remove Cu2+ and Cd2+ from aqueous solutions. CS-HMF derivatives were characterized both before, and after, metal ions adsorption by using scanning electron microscopy (SEM), as well as Fourier-transform infrared (FTIR) spectroscopy thermogravimetric analysis (TGA), and X-Ray diffraction analysis (XRD). The CS-HMF derivatives were tested at pH = 5 and showed higher adsorption capacity with the increase of temperature. Also, the equilibrium data were fitted to Langmuir (best fitting) and Freundlich model, while the kinetic data to pseudo-first (best fitting) and pseudo-second order equations. The Langmuir model fitted better (higher R2) the equilibrium data than the Freundlich equation. By increasing the HMF grafting from 130% (CS-HMF1) to 310% (CS-HMF3), an increase of 24% (26 m/g) was observed for Cu2+ adsorption and 19% (20 mg/g) for Cd2+. By increasing from T = 25 to 65 °C, an increase of the adsorption capacity (metal uptake) was observed. Ten reuse cycles were successfully carried out without significant loss of adsorption ability. The reuse potential was higher of Cd2+, but more stable desorption reuse ability during all cycles for Cu2+.

Graphene-Based Nanocomposites for Enhanced Pb2+ Adsorption

2017 ◽  
Vol 13 ◽  
pp. 323-329 ◽  
Author(s):  
Anastasiya E. Kucherova ◽  
Irina V. Romantsova ◽  
Alexandr E. Burakov ◽  
Nariman R. Memetov ◽  
Mikhail N. Krasnyansky
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Kinetic Data ◽  
Adsorption Equilibrium ◽  
Intercalation Compound ◽  
Expanded Graphite ◽  
Graphite Intercalation Compound ◽  
Order Model ◽  
Graphite Intercalation ◽  
Pseudo Second Order

The present paper describes an investigation of the adsorption of lead ions (Pb2+) on graphene-based nanocomposites obtained via exfoliation of hydrolyzed expanded graphite intercalation compound. Three types of these nanocomposites - suspension of graphene nanoplatelets (SGN), paste of multi-layered oxidized graphene (PMOG), and paste of few-layered oxidized graphene (PFOG) - were used to extract Pb2+ from 1,040 mg L-1 aqueous solutions of Pb (NO3)2, and the kinetic of the Pb2+ adsorption was studied. It was found that the kinetic data are best fitted by the pseudo-second-order model. The adsorption equilibrium was achieved within 30 min under normal conditions. The maximum Pb2+ adsorption capacity of SGN, PMOG and PFOG was found to be 457, 103 and 38 mg g-1, respectively. Considering the obtained results, it can be assumed that the phenolic and hydroxyl oxygen-containing functional groups located at the surface of the adsorption materials under study play an important role in the Pb2+ removal process.

scholarly journals Removal of triphenylmethane dye from aqueous solutions through an adsorption process over waste materials

2020 ◽  
Vol 10 (4) ◽  
pp. 5772-5779
Keyword(s):  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Dye Removal ◽  
Functional Group ◽  
Adsorption Process ◽  
Removal Rate ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Pseudo Second Order ◽  
Best Fit

Water pollution is the most significant issue due to rapid growing industrial development especially textile dye industry. Therefore, the adsorption process experiment was conducted to determine the removal ability of the adsorbent chosen. The removal rate and adsorption capacity of Phenol red and Cresol were analyzed by using eggshell adsorbent in the adsorption process. The experiment was conducted with parameters of initial concentration, dosage, pH and contact time. Results indicated that the removal rate achieved more than 90% and the adsorption capacity exceeded more than 5 mg/g. The functional group before adsorption process eggshell adsorbent and after adsorption process eggshell adsorbent was analyzed by using FTIR (Fourier Transform Infrared Spectroscopy). The study of adsorption isotherm and kinetics model was carried out to identify the efficiency of the eggshell adsorbent reacting with the dye solution. The adsorption isotherm that applied in this research was Langmuir isotherm, Jovanovic isotherm and Freundlich isotherm. Moreover, Pseudo-first-order and Pseudo-second-order chosen were conducted to determine the kinetic studies. In short, eggshell adsorbent is highly effective on dye removal through adsorption capacity. The functional group of the eggshell adsorbent was found such as alcohols, phenol, alkanes, carbonyls, ester, saturated aliphatic, aldehydes, aromatics, 2°amines and phosphorus. For kinetics study, Freundlich isotherm was analyzed as the best fit isotherm model as it achieved the highest R2 value which is closed to 1 and Pseudo-second-order was analyzed as the best fit kinetic model in this experiment. Therefore, eggshell adsorbent is highly effective in dye removal.

scholarly journals Comparative Study of Biochar Modified with Different Functional Groups for Efficient Removal of Pb(II) and Ni(II)

2021 ◽  
Author(s):  
Chengchen Liu ◽  
Jiaxin Lin ◽  
Haojia Chen ◽  
Wanjun Wang ◽  
Yan Yang
Keyword(s):  
Adsorption Capacity ◽  
Functional Groups ◽  
Ethylenediaminetetraacetic Acid ◽  
X Ray Diffraction ◽  
Modified Biochar ◽  
Hierarchical Porous ◽  
Phosphorus Containing ◽  
Removal Of Heavy Metals ◽  
Pseudo Second Order ◽  
Ft Ir

Abstract The potential application of biochar in water treatment is attracting interest due to its sustainability and low production cost. In the present study, H3PO4-modified biochar (H-PBC), ethylenediaminetetraacetic acid-modified biochar (E-PBC), and NaOH-modified biochar (O-PBC) were prepared for Ni(II) and Pb(II) adsorption in an aqueous solution. Scanning electron microscopy (SEM), X-ray diffraction analysis, Brunauer–Emmett–Teller analysis, and Fourier transform infrared (FT-IR) spectroscopy were employed to characterize the as-obtained samples, and their capacities for Ni(II) and Pb(II) adsorption were determined. SEM showed that H-PBC retained the hierarchical porous structure of pristine biochar, and projections were observed on its surface. FT-IR showed that H-PBC possessed abundant oxygen-containing and phosphorus-containing functional groups on the surface. H-PBC, E-PBC, and O-PBC all exhibited excellent performance at Ni(II) and Pb(II) adsorption with qmax values of 64.94 mg/g, 47.17 mg/g, and 60.24 mg/g, and 243.90 mg/g, 156.25 mg/g, and 192.31 mg/g, respectively, which were significantly higher than the adsorption capacity (19.80 mg/g and 38.31 mg/g) of pristine biochar. Pseudo-second order models suggested that the adsorption process was controlled by chemical adsorption. Regeneration analysis showed that H-PBC had superior reusability characteristics. H-PBC had a greater adsorption capacity than other adsorbents due to its large specific surface area, and abundant oxygen-containing and phosphorus-containing functional groups. The results obtained in this study suggest that H-PBC is a promising adsorbent for the removal of heavy metals from aqueous solutions.

Treated Clay Mineral as Adsorbent for the Removal of Heavy Metals from Aqueous Solution

2021 ◽  
Author(s):  
Paul Egwuonwu Dim ◽  
Mutsee Termtanun
Keyword(s):  
Heavy Metals ◽  
Adsorption Capacity ◽  
Adsorption Equilibrium ◽  
Kinetic Constant ◽  
Specific Area ◽  
Batch Method ◽  
Chromium Vi ◽  
Removal Of Heavy Metals ◽  
Pseudo Second Order ◽  
Best Fit

The decontamination of heavy metals present in aquatic bodies is a significant challenge that requires urgent attention. Analytical methods such as BET, XRF, SEM-EDX, and XRD was employed to characterize the raw clay (NT) and acid treated clay (AT). The adsorption of Cr (VI) and Fe (III) onto AT was performed using the batch method. The effects of time, adsorbent dose, temperature, and pH show that the optimal conditions are 50 min, 0.3 g, 35°C, and pH 6. The surface area of AT was 389.37 m2/g, and the adsorption equilibrium time of AT was 50 min. Langmuir isotherms had the best fit. Adsorption capacity is 18.15 and 39.80 mg/g for Cr (VI) and Fe (III) ions, respectively. An increase in area considerably improved the adsorption capacity of AT in the surface specific area. The interaction of Cr (VI) and Fe (III) ions onto AT indicated spontaneous and endothermic reaction. The chromium (VI) kinetic constant (k2 = 1.679) was faster compared to Fe (III) rate constant (k2 = 0.0526). It agreed correctly with the pseudo-second-order equation. The sum square error (SSE) value obtained confirmed the best-fit equations. The percent adsorbed for Cr (VI) and Fe (III) is 74 and 90%. The results revealed that iron has a higher affinity towards AT than chromium. The study revealed that AT could be suitable and effective in the adsorption of chromium and iron in the wastewater medium.

scholarly journals Preparation and characterization of chitosan/Fe2O3 nano composite for the adsorption of thorium (IV) ion from aqueous solution

2018 ◽  
Vol 78 (3) ◽  
pp. 708-720 ◽  
Author(s):  
B. Rouhi Broujeni ◽  
A. Nilchi ◽  
A. H. Hassani ◽  
R. Saberi
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Ion Concentration ◽  
P Value ◽  
X Ray Diffraction ◽  
Nano Composite ◽  
Statistical Measures ◽  
Pseudo Second Order

Abstract In this study, novel chitosan/Fe2O3nano composite Ch/Fe-Onc was synthesized and evaluated as an adsorbent for removing thorium (IV) (Th4+) ion from aqueous solution. The Ch/Fe-Onc was characterized by X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). Response surface methodology (RSM) was used in the optimization of Th4+ adsorption for parameters such as pH, the initial metal ion concentration (Th4+ concentration) and contact time. The statistical measures (i.e. analysis of variance, R2, the lack of fit test and the P value) specify that the developed model is proper. Furthermore, the adsorption kinetics was well defined by the pseudo-second-order equation, while the adsorption isotherms were better fitted by the Langmuir model. The adsorption capacity of Ch/Fe-Onc was 430 mg Th4+g−1 composite which leads to 99% removal at 25 °C. Moreover, thermodynamic parameters which state the natural and endothermic nature of the reactions were determined. The loaded Th4+ can be easily regenerated with HNO3 and the Ch/Fe-Onc can be used repeatedly without any significant reduction in its adsorption capacity. The desorption level of Th4+ from the Ch/Fe-Onc by using 0.1 M HNO3, was more than 95%.

Sign in / Sign up

Export Citation Format

Share Document