Flow field induced particle accumulation inside droplets in rectangular channels

Lab on a Chip ◽  
2015 ◽  
Vol 15 (13) ◽  
pp. 2879-2886 ◽  
Author(s):  
Michael Hein ◽  
Michael Moskopp ◽  
Ralf Seemann
Keyword(s):  
Flow Field ◽  
Internal Flow ◽  
Droplet Velocity ◽  
Topological Change ◽  
Particle Accumulation ◽  
Rectangular Channels

We present accumulation of sedimenting particles/cells within elongated droplets. Particle patterns evolve with droplet velocity, as explained by a topological change of the internal flow and the droplet's outer shape.

scholarly journals Numerical Simulation and Experimental Study on Flow Field in a Swirl Nozzle

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Yicheng Sun ◽  
Yufan Fu ◽  
Baohui Chen ◽  
Jiaxing Lu ◽  
Wanquan Deng
Keyword(s):  
Flow Field ◽  
Velocity Distribution ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Low Pressure ◽  
External Flow ◽  
Droplet Velocity ◽  
Inlet Pressure ◽  
Outlet Section ◽  
Local Pressure

In order to study the internal flow characteristics and external droplet velocity distribution characteristics of the swirl nozzle, the following methods were used: numerical simulations were used to study the internal flow characteristics of a swirl nozzle and phase Doppler particle velocimetry was used to determine the corresponding external droplet velocity distribution under medium and low pressure conditions. The distributions of pressure and water velocity inside the nozzle were obtained. Meanwhile, the velocities of droplets outside the nozzle in different sections were discussed. The results show that the flow rate in the swirl nozzle increases with the increase in inlet pressure, and the local pressure in the region decreases because of the excessive velocity at the internal outlet section of the swirl nozzle, resulting in cavitation. The experimental results show that under an external flow field, the minimum droplet velocity occurs in the axial direction; starting from the axis, the velocity first increases and then decreases along the radial direction. Swirling motion inside the nozzle and velocity variations in the external flow field occur under medium and low pressure conditions. The relationship between the inlet pressure and the distributions of water droplets’ velocities was established, which provides a reference for the research and development of the swirl nozzle.

THE INTERNAL FLOW FIELD ASSOCIATED WITH YAWED THREE-DIMENSIONAL RECTANGULAR CAVITIES

2000 ◽  
Vol 7 (3) ◽  
pp. 14
Author(s):  
Eric Savory ◽  
Norman Toy ◽  
Shiki Okamoto ◽  
Yoko Yamanishi
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Internal Flow

scholarly journals Influence of wall roughness on cavitation performance of centrifugal pump

2021 ◽  
Vol 43 (6) ◽  
Author(s):  
Weihui Xu ◽  
Xiaoke He ◽  
Xiao Hou ◽  
Zhihao Huang ◽  
Weishu Wang
Keyword(s):  
Flow Field ◽  
Centrifugal Pump ◽  
Internal Flow ◽  
Wall Roughness ◽  
Blade Surface ◽  
Centrifugal Pumps ◽  
Three Dimensional Model ◽  
Cavitation Inception ◽  
Cavitation Performance ◽  
Critical Cavitation

AbstractCavitation is a phenomenon that occurs easily during rotation of fluid machinery and can decrease the performance of a pump, thereby resulting in damage to flow passage components. To study the influence of wall roughness on the cavitation performance of a centrifugal pump, a three-dimensional model of internal flow field of a centrifugal pump was constructed and a numerical simulation of cavitation in the flow field was conducted with ANSYS CFX software based on the Reynolds normalization group k-epsilon turbulence model and Zwart cavitation model. The cavitation can be further divided into four stages: cavitation inception, cavitation development, critical cavitation, and fracture cavitation. Influencing laws of wall roughness of the blade surface on the cavitation performance of a centrifugal pump were analyzed. Research results demonstrate that in the design process of centrifugal pumps, decreasing the wall roughness appropriately during the cavitation development and critical cavitation is important to effectively improve the cavitation performance of pumps. Moreover, a number of nucleation sites on the blade surface increase with the increase in wall roughness, thereby expanding the low-pressure area of the blade. Research conclusions can provide theoretical references to improve cavitation performance and optimize the structural design of the pump.

scholarly journals Analysis of the Influence of Different Bionic Structures on the Noise Reduction Performance of the Centrifugal Pump

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 886
Author(s):  
Cui Dai ◽  
Chao Guo ◽  
Yiping Chen ◽  
Liang Dong ◽  
Houlin Liu
Keyword(s):  
Flow Field ◽  
Noise Reduction ◽  
Centrifugal Pump ◽  
Great Influence ◽  
Frequency Doubling ◽  
Sound Field ◽  
Internal Flow ◽  
Test System ◽  
Centrifugal Pumps ◽  
External Characteristics

The strong noise generated during the operation of the centrifugal pump harms the pump group and people. In order to decrease the noise of the centrifugal pump, a specific speed of 117.3 of the centrifugal pump is chosen as a research object. The bionic modification of centrifugal pump blades is carried out to explore the influence of different bionic structures on the noise reduction performance of centrifugal pumps. The internal flow field and internal sound field of bionic blades are studied by numerical calculation and test methods. The test is carried out on a closed pump test platform which includes external characteristics and a flow noise test system. The effects of two different bionic structures on the external characteristics, acoustic amplitude–frequency characteristics and flow field structure of a centrifugal pump, are analyzed. The results show that the pit structure has little influence on the external characteristic parameters, while the sawtooth structure has a relatively great influence. The noise reduction effect of the pit structure is aimed at the wide-band noise, while the sawtooth structure is aimed at the discrete noise of the blade-passing frequency (BPF) and its frequency doubling. The noise reduction ability of the sawtooth structure is not suitable for high-frequency bands.

Visualization of Internal Flow Field of Propeller Fan

2017 ◽  
Author(s):  
Takaya Onishi ◽  
H. Sato ◽  
M. Hayakawa ◽  
Y. Kawata
Keyword(s):  
Flow Field ◽  
High Performance ◽  
Laser Light ◽  
Internal Flow ◽  
Light Sheet ◽  
Tip Vortex ◽  
Laser Light Sheet ◽  
Blade Surface ◽  
Similar Tendency ◽  
Flow Phenomena

Propeller fans are required not only to have high performance but also to be extremely quiet. The internal flow field of ventilation propeller fans is even more complicated because they usually have a very peculiar configuration with protruding blades upstream. Thus, many kinds of internal vortices yield which cause noise and their cause and countermeasures are needed to be clarified. The purposes of this paper are to visualize the internal flow of the propeller fan from the static and rotating frame of reference. The internal flow visualization measured from the static frame gives approximately the scale of the tip vortex. The visualization from the rotating coordinate system yields a better understanding of the flow phenomena occurring at the specific blade. The experiment is implemented by using a small camera mounted on the shaft of the fan and rotated it to capture the behavior of the vortices using a laser light sheet to irradiate the blade surface. Hence, the flow field of the specific blade could be understood to some extent. The visualized results are compared with the CFD results and these results show a similar tendency about the generation point and developing process of the tip vortex. In addition, it is found that the noise measurement result is relevant to the effect of tip vortex from the visualization result.

Research on CFD Simulation of the Cement Slurry Mixer

2012 ◽  
Vol 621 ◽  
pp. 196-199
Author(s):  
Shui Ping LI ◽  
Ya Li Yuan ◽  
Lu Gang Shi
Keyword(s):  
Flow Field ◽  
High Performance ◽  
Cfd Simulation ◽  
Structural Parameters ◽  
Internal Flow ◽  
Simulation Method ◽  
Cement Slurry ◽  
Fluid Machinery ◽  
Computational Fluid Dynamics Cfd ◽  
Machinery Design

Numerical simulation method of the internal flow field of fluid machinery has become an important technology in the study of fluid machinery design. In order to obtain a high-performance cement slurry mixer, computational fluid dynamics (CFD) techniques are used to simulate the flow field in the mixer, and the simulation results are studied. According to the analysis results, the structural parameters of the mixer are modified. The results show the mixer under the revised parameters meet the design requirements well. So CFD analysis method can shorten design period and provide valuable theoretical guidance for the design of fluid machinery.

The Influence of Wrap Angle of Blade on the Internal Flow Field and Hydraulic Performance of Double Suction Pump

2018 ◽  
Author(s):  
Hao Chang ◽  
Weidong Shi ◽  
Wei Li ◽  
Jianrui Liu ◽  
Ling Zhou ◽  
...  
Keyword(s):  
Flow Field ◽  
Cross Section ◽  
Turbulence Model ◽  
Static Pressure ◽  
Internal Flow ◽  
Hydraulic Performance ◽  
Optimal Model ◽  
Suction Pump ◽  
External Characteristic ◽  
Wrap Angle

In order to study the influence rule of wrap angle of blade on the internal flow field and hydraulic performance of double suction pump, 5 kinds of wrap angles of blade with 100°, 110°, 120°, 130° and 140° are designed in this paper. The turbulence model and the grid type are analyzed, the performance of ES350-575 double suction pump is obtained by employ the software CFX. The static pressure and velocity distributions in the cross-section are analyzed. Therefore, the optimal model is obtained, and the relevant external characteristic test is conducted. The result shows that the reasonable increase of the wrap angle of blade can enhance the performance of the pump effectively, which can improve the static pressure and velocity distributions of the internal flow field.

Internal Flow Losses: A Fresh Look at Old Concepts

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Bastian Schmandt ◽  
Heinz Herwig
Keyword(s):  
Flow Field ◽  
Entropy Generation ◽  
Mechanical Energy ◽  
Internal Flow ◽  
Second Law Of Thermodynamics ◽  
Head Loss ◽  
Local Entropy ◽  
Flow Losses ◽  
Loss Coefficients ◽  
Local Entropy Generation

Losses in a flow field due to single conduit components often are characterized by experimentally determined head loss coefficients K. These coefficients are defined and determined with the pressure as the critical quantity. A thermodynamic definition, given here as an alternative, is closer to the physics of flow losses, however. This definition is based upon the dissipation of mechanical energy as main quantity. With the second law of thermodynamics this dissipation can be linked to the local entropy generation in the flow field. For various conduit components K values are determined and physically interpreted by determining the entropy generation in the component as well as upstream and downstream of it. It turns out that most of the losses occur downstream of the components what carefully has to be taken into account when several components are combined in a flow network.

Sign in / Sign up

Export Citation Format

Share Document