Functionalization of AgNWs with amino groups and their application in an epoxy matrix for antistatic and thermally conductive nanocomposites

RSC Advances ◽  
2015 ◽  
Vol 5 (111) ◽  
pp. 91516-91523 ◽  
Author(s):  
Tengyun Zhao ◽  
Chen Zhang ◽  
Zhongjie Du ◽  
Hangquan Li ◽  
Wei Zou
Keyword(s):  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Resin Matrix ◽  
Amino Groups ◽  
Epoxy Nanocomposites ◽  
Epoxy Resin Matrix ◽  
Conductive Nanocomposites ◽  
Thermally Conductive

AgNWs were functionalized to improve their dispersion in an epoxy resin matrix, making AgNW–epoxy nanocomposites with high antistatic and thermal performances.

scholarly journals Use of Cement Suspension as an Alternative Matrix Material for Textile-Reinforced Concrete

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2127
Author(s):  
Richard Fürst ◽  
Eliška Fürst ◽  
Tomáš Vlach ◽  
Jakub Řepka ◽  
Marek Pokorný ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Epoxy Resin ◽  
High Performance Concrete ◽  
Bending Test ◽  
Resin Matrix ◽  
Cement Matrix ◽  
Sample Type ◽  
Textile Reinforced Concrete ◽  
Epoxy Resin Matrix ◽  
Four Point Bending

Textile-reinforced concrete (TRC) is a material consisting of high-performance concrete (HPC) and tensile reinforcement comprised of carbon roving with epoxy resin matrix. However, the problem of low epoxy resin resistance at higher temperatures persists. In this work, an alternative to the epoxy resin matrix, a non-combustible cement suspension (cement milk) which has proven stability at elevated temperatures, was evaluated. In the first part of the work, microscopic research was carried out to determine the distribution of particle sizes in the cement suspension. Subsequently, five series of plate samples differing in the type of cement and the method of textile reinforcement saturation were designed and prepared. Mechanical experiments (four-point bending tests) were carried out to verify the properties of each sample type. It was found that the highest efficiency of carbon roving saturation was achieved by using finer ground cement (CEM 52.5) and the pressure saturation method. Moreover, this solution also exhibited the best results in the four-point bending test. Finally, the use of CEM 52.5 in the cement matrix appears to be a feasible variant for TRC constructions that could overcome problems with its low temperature resistance.

scholarly journals Assessing the Flexural Properties of Epoxy Composites with Extremely Low Addition of Cellulose Nanofiber Content

2020 ◽  
Vol 10 (3) ◽  
pp. 1159 ◽  
Author(s):  
Yingmei Xie ◽  
Hiroki Kurita ◽  
Ryugo Ishigami ◽  
Fumio Narita
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Flexural Modulus ◽  
Strengthening Mechanism ◽  
Short Fiber ◽  
Cellulose Nanofiber ◽  
Resin Matrix ◽  
Element Analysis ◽  
Epoxy Resin Matrix ◽  
The Matrix

Epoxy resins are a widely used common polymer due to their excellent mechanical properties. On the other hand, cellulose nanofiber (CNF) is one of the new generation of fibers, and recent test results show that CNF reinforced polymers have high mechanical properties. It has also been reported that an extremely low CNF addition increases the mechanical properties of the matrix resin. In this study, we prepared extremely-low CNF (~1 wt.%) reinforced epoxy resin matrix (epoxy-CNF) composites, and tried to understand the strengthening mechanism of the epoxy-CNF composite through the three-point flexural test, finite element analysis (FEA), and discussion based on organic chemistry. The flexural modulus and strength were significantly increased by the extremely low CNF addition (less than 0.2 wt.%), although the theories for short-fiber-reinforced composites cannot explain the strengthening mechanism of the epoxy-CNF composite. Hence, we propose the possibility that CNF behaves as an auxiliary agent to enhance the structure of the epoxy molecule, and not as a reinforcing fiber in the epoxy resin matrix.

Investigation of Fiber-Reinforced Modified Epoxy Resin Composites

2012 ◽  
Vol 510-511 ◽  
pp. 577-584 ◽  
Author(s):  
A. Quddos ◽  
Mohammad Bilal Khan ◽  
R.N. Khan ◽  
M.K.K. Ghauri
Keyword(s):  
Epoxy Resin ◽  
High Strength ◽  
Polymeric Matrix ◽  
Fiber Reinforced Composites ◽  
Resin Matrix ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Epoxy Resin Matrix ◽  
The Matrix ◽  
Modified Epoxy

The impregnation of the fiber with a resin system, the polymeric matrix with the interface needs to be properly cured so that the dimensional stability of the matrix and the composite is ensured. A modified epoxy resin matrix was obtained with a reactive toughening agent and anhydride as a curing agent. The mechanical properties of the modified epoxy matrix and its fiber reinforced composites were investigated systematically. The polymeric matrix possessed many good properties, including high strength, high elongation at break, low viscosity, long pot life at room temperature, and good water resistance. The special attentions are given to the matrix due to its low out gassing, low water absorption and radiation resistance. In addition, the fiber-reinforced composites showed a high strength conversion ratio of the fiber and good fatigue resistance. The dynamic and static of the composite material were studied by thermo gravimetric analysis (TGA), Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) with EDX. The influences of processing technique such as curing and proper mixing on the mechanical and interfacial properties were determined. The results demonstrated that the modified epoxy resin matrix is very suitable for applications in products fabricated with fiber-reinforced composites.

Effect of γ irradiation on the properties of basalt fiber reinforced epoxy resin matrix composite

2015 ◽  
Vol 466 ◽  
pp. 100-107 ◽  
Author(s):  
Ran Li ◽  
Yizhuo Gu ◽  
Zhongjia Yang ◽  
Min Li ◽  
Shaokai Wang ◽  
...  
Keyword(s):  
Epoxy Resin ◽  
Matrix Composite ◽  
Basalt Fiber ◽  
Resin Matrix ◽  
Fiber Reinforced ◽  
Γ Irradiation ◽  
Epoxy Resin Matrix ◽  
Resin Matrix Composite

Preparation and Mechanical Properties of Epoxy Resin Reinforced with Jeffamines-Grafted Carbon Nanotubes

2009 ◽  
Vol 79-82 ◽  
pp. 553-556 ◽  
Author(s):  
Ling Fei Shi ◽  
Gang Li ◽  
Gang Sui ◽  
Xiao Ping Yang
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Epoxy Resin ◽  
Photoelectron Spectroscopy ◽  
Epoxy Matrix ◽  
Resin Matrix ◽  
Mechanical And Thermal Properties ◽  
Time Dynamic ◽  
Multi Walled Carbon Nanotubes ◽  
The Impact

The increasing proliferation and application of advanced polymer composites requires higher and broader performance resin matrices. Poly(oxypropylene) with –NH2 end-groups has been widely used to toughen epoxy resins, but the strength of resin matrix may be reduced due to the addition of flexible segments in the crosslinking network. Carbon nanotubes (CNTs) have been paid more and more attention in recent years because of their superior thermal and mechanical properties. In this paper, CNTs grafted with Jeffamines T403 were used to simultaneously improve the reinforcement and toughening of an epoxy resin. The untreated multi-walled carbon nanotubes (u-MWNTs) were functionalized with amine groups according to three steps: carboxylation, acylation, and amidation. The f-MWNTs were characterized by Fourier transform infra-red (FTIR) and X-ray photoelectron spectroscopy (XPS). The experimental results indicated that the T403 was grafted to the surface of MWCNTs. The mechanical and thermal properties of epoxy with f-MWNTs were investigated. The tensile and flexural strength increased by 7.77 % and 7.03 % after adding 0.5wt% f-MWCNTs without sacrificing the impact toughness. At the same time, dynamic mechanical thermal analysis (DMTA) showed that the glass transition temperature (Tg) of epoxy with f-MWNTs were increased. The fracture surface of epoxy with f-MWNTs was observed by scanning electron microscopy (SEM) to understand the dispersion of f-MWNTs in epoxy matrix and interfacial adhesion between f-MWNTs and epoxy matrix, which can be attributed to the strong interfacial bonding between f-MWNTs and epoxy resin.

Sign in / Sign up

Export Citation Format

Share Document