scholarly journals Effect of hydrogen addition in diesel/natural gas dual-fuel combustion with late injection

2021 ◽  
Vol 312 ◽  
pp. 08005
Author(s):  
Antonio Caricato ◽  
Antonio Paolo Carlucci ◽  
Antonio Ficarella ◽  
Luciano Strafella
Keyword(s):  
Natural Gas ◽  
Conversion Efficiency ◽  
Early Stage ◽  
Combustion Process ◽  
Pollutant Emission ◽  
Dual Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Fuel Conversion ◽  
Hydrogen Addition

In a previous work, the effectiveness of late pilot injection on improving combustion behaviour – in terms of fuel conversion efficiency and pollutant emission levels – in a diesel/natural gas dual-fuel engine was assessed. Then, an additional set of experiments was performed, aiming at speeding up the combustion process possibly without penalizing NOx levels. Therefore, hydrogen was added to natural gas in a percentage equal to 10%. Results show that hydrogen addition has a significant effect on the combustion development specially during the early stage of combustion: ignition delay is shortened and combustion centre is advanced, while the combustion duration increases when pilot injection timing is set to conventional values, while remains basically unchanged for late timings. Fuel conversion efficiency is only slightly penalized when hydrogen is added. Moreover, it was confirmed that, in general, combustion strategy with late pilot injection timing does not penalize fuel conversion efficiency; indeed, in some cases, it actually increases. Concerning regulated emission levels, it is again proven that late pilot injection does not penalize pollutant production: the hydrocarbons and carbon monoxide reduce as pilot injection is delayed, probably due to the higher temperatures reached into the cylinder during most part of the expansion stroke. Moreover, adding hydrogen always reduces their levels. Concerning NOx, they are drastically reduced delaying pilot injection; as expected, hydrogen addition promotes NOx formation, but the increase, evident with conventional pilot injection timings, becomes marginal with late injection strategy. Therefore, combustion strategy performance with late pilot injection in dual-fuel diesel/natural gas combustion conditions can be further improved with 10% hydrogen addition to natural gas.

scholarly journals A Numerical Study on the Combustion Process and Emission Characteristics of a Natural Gas-Diesel Dual-Fuel Marine Engine at Full Load

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1342
Author(s):  
Van Chien Pham ◽  
Jae-Hyuk Choi ◽  
Beom-Seok Rho ◽  
Jun-Soo Kim ◽  
Kyunam Park ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Simulation Software ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Cylinder Pressure ◽  
Marine Engine ◽  
Full Load ◽  
Simulation Results

This paper presents research on the combustion and emission characteristics of a four-stroke Natural gas–Diesel dual-fuel marine engine at full load. The AVL FIRE R2018a (AVL List GmbH, Graz, Austria) simulation software was used to conduct three-dimensional simulations of the combustion process and emission formations inside the engine cylinder in both diesel and dual-fuel mode to analyze the in-cylinder pressure, temperature, and emission characteristics. The simulation results were then compared and showed a good agreement with the measured values reported in the engine’s shop test technical data. The simulation results showed reductions in the in-cylinder pressure and temperature peaks by 1.7% and 6.75%, while NO, soot, CO, and CO2 emissions were reduced up to 96%, 96%, 86%, and 15.9%, respectively, in the dual-fuel mode in comparison with the diesel mode. The results also show better and more uniform combustion at the late stage of the combustions inside the cylinder when operating the engine in the dual-fuel mode. Analyzing the emission characteristics and the engine performance when the injection timing varies shows that, operating the engine in the dual-fuel mode with an injection timing of 12 crank angle degrees before the top dead center is the best solution to reduce emissions while keeping the optimal engine power.

Simulation Research on Combustion Process in a Natural Gas-Diesel Dual-Fuel Marine Engine

2014 ◽  
Vol 525 ◽  
pp. 227-231 ◽  
Author(s):  
Min Xiao ◽  
Chun Long Feng
Keyword(s):  
Natural Gas ◽  
Total Energy ◽  
Combustion Process ◽  
Power Reduction ◽  
Dual Fuel ◽  
Injection Timing ◽  
Simulation Research ◽  
Injection Duration ◽  
Medium Speed ◽  
The Right

In order to solve the problem of Diesel natural gas dual fuel engine, such as power reduction, low charging efficiency, the conception of diesel engine fueled with pilot-ignited directly-injected liquefied natural gas is put forward. On the basis of this theory, a medium speed diesel of the marine is refitted into dual fuel engine, in order to keep original power, decrease the temperature of combustion and reduce emission. The LNG injection timing, duration of LNG injection and the different ratios the pilot diesel to total energy are studied the method of AVL FIRE software. Conclusions are as follows: When the different ratios pilot diesel to total energy is 0.5%, the engine can not work; Delaying the LNG injection timing, shortening the LNG injection duration and choose the right ratios pilot diesel to total energy can reach the indicated power of original machine, and the NOx emissions level will be greatly reduced.

scholarly journals Numerical Analysis of High-Pressure Direct Injection Dual-Fuel Diesel-Liquefied Natural Gas (LNG) Engines

Processes ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 261 ◽  
Author(s):  
Alberto Boretti
Keyword(s):  
High Pressure ◽  
Steady State ◽  
Liquid Phase ◽  
Natural Gas ◽  
Power Density ◽  
Conversion Efficiency ◽  
Liquefied Natural Gas ◽  
Dual Fuel ◽  
Fuel Conversion ◽  
Better Than

Dual fuel engines using diesel and fuels that are gaseous at normal conditions are receiving increasing attention. They permit to achieve the same (or better) than diesel power density and efficiency, steady-state, and substantially similar transient performances. They also permit to deliver better than diesel engine-out emissions for CO2, as well as particulate matter, unburned hydrocarbons, and nitrous oxides. The adoption of injection in the liquid phase permits to further improve the power density as well as the fuel conversion efficiency. Here, a model is developed to study a high-pressure, 1600 bar, liquid phase injector for liquefied natural gas (LNG) in a high compression ratio, high boost engine. The engine features two direct injectors per cylinder, one for the diesel and one for the LNG. The engine also uses mechanically assisted turbocharging (super-turbocharging) to improve the steady-state and transient performances of the engine, decoupling the power supply at the turbine from the power demand at the compressor. Results of steady-state simulations show the ability of the engine to deliver top fuel conversion efficiency, above 48%, and high efficiencies, above 40% over the most part of the engine load and speed range. The novelty of this work is the opportunity to use very high pressure (1600 bar) LNG injection in a dual fuel diesel-LNG engine. It is shown that this high pressure permits to increase the flow rate per unit area; thus, permitting smaller and lighter injectors, of faster actuation, for enhanced injector-shaping capabilities. Without fully exploring the many opportunities to shape the heat release rate curve, simulations suggest two-point improvements in fuel conversion efficiency by increasing the injection pressure.

scholarly journals A Numerical Study on the Pilot Injection Conditions of a Marine 2-Stroke Lean-Burn Dual Fuel Engine

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1396
Author(s):  
Hao Guo ◽  
Song Zhou ◽  
Jiaxuan Zou ◽  
Majed Shreka
Keyword(s):  
Natural Gas ◽  
Fuel Injection ◽  
Numerical Study ◽  
Pollutant Emissions ◽  
Dual Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Lean Burn ◽  
Injection Duration ◽  
Pilot Fuel

The global demand for clean fuels is increasing in order to meet the requirements of the International Maritime Organization (IMO) of 0.5% global Sulphur cap and Tier III emission limits. Natural gas has begun to be popularized on liquefied natural gas (LNG) ships because of its low cost and environment friendly. In large-bore marine engines, ignition with pilot fuel in the prechamber is a good way to reduce combustion variability and extend the lean-burn limit. However, the occurrence of knock limits the increase in power. Therefore, this paper investigates the effect of pilot fuel injection conditions on performance and knocking of a marine 2-stroke low-pressure dual-fuel (LP-DF) engine. The engine simulations were performed under different pilot fuel parameters. The results showed that the average in-cylinder temperature, the average in-cylinder pressure, and the NOx emissions gradually decreased with the delay of the pilot injection timing. Furthermore, the combustion situation gradually deteriorated as the pilot injection duration increased. A shorter pilot injection duration was beneficial to reduce NOx pollutant emissions. Moreover, the number of pilot injector orifices affected the ignition of pilot fuel and the flame propagation speed inside the combustion chamber.

Improving the Efficiency of the Advanced Injection Low Pilot Ignited Natural Gas Engine Using Organic Rankine Cycles

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
K. K. Srinivasan ◽  
P. J. Mago ◽  
G. J. Zdaniuk ◽  
L. M. Chamra ◽  
K. C Midkiff
Keyword(s):  
Natural Gas ◽  
Conversion Efficiency ◽  
Waste Heat ◽  
Injection Timing ◽  
Base Line ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Conversion ◽  
Lean Combustion ◽  
Organic Rankine Cycles

Intense energy security debates amidst the ever increasing demand for energy in the US have provided sufficient impetus to investigate alternative and sustainable energy sources to the current fossil fuel economy. This paper presents the advanced (injection) low pilot ignition natural gas (ALPING) engine as a viable, efficient, and low emission alternative to conventional diesel engines, and discusses further efficiency improvements to the base ALPING engine using organic rankine cycles (ORC) as bottoming cycles. The ALPING engine uses advance injection (50–60deg BTDC) of very small diesel pilots in the compression stroke to compression ignite a premixed natural gas-air mixture. It is believed that the advanced injection of the higher cetane diesel fuel leads to longer in-cylinder residence times for the diesel droplets, thereby resulting in distributed ignition at multiple spatial locations, followed by lean combustion of the higher octane natural gas fuel via localized flame propagation. The multiple ignition centers result in faster combustion rates and higher fuel conversion efficiencies. The lean combustion of natural gas leads to reduction in local temperatures that result in reduced oxides of nitrogen (NOx) emissions, since NOx emissions scale with local temperatures. In addition, the lean premixed combustion of natural gas is expected to produce very little particulate matter emissions (not measured). Representative base line ALPING (60deg BTDC pilot injection timing) (without the ORC) half load (1700rpm, 21kW) operation efficiencies reported in this study are about 35% while the corresponding NOx emission is about 0.02g∕kWh, which is much lower than EPA 2007 Tier 4 Bin 5 heavy-duty diesel engine statutes of 0.2g∕kWh. Furthermore, the possibility of improving fuel conversion efficiency at half load operation with ORCs using “dry fluids” is discussed. Dry organic fluids, due to their lower critical points, make excellent choices for waste heat recovery Rankine cycles. Moreover, previous studies indicate that dry fluids are more preferable compared to wet fluids because the need to superheat the fluid to extract work from the turbine is eliminated. The calculations show that ORC—turbocompounding results in fuel conversion efficiency improvements of the order of 10% while maintaining the essential low NOx characteristics of ALPING combustion.

Sign in / Sign up

Export Citation Format

Share Document