scholarly journals Vibratory bed assisted infrared drying of parboiled rice and its rice bran stability

2018 ◽  
Vol 192 ◽  
pp. 03060
Author(s):  
Pattarachai Vichaiya ◽  
Jiraporn Sripinyowanich Jongyingcharoen
Keyword(s):  
Rice Bran ◽  
Dry Matter ◽  
Drying Time ◽  
Drying Characteristics ◽  
Parboiled Rice ◽  
Infrared Drying ◽  
Hot Air ◽  
Head Rice ◽  
The Stability

The purposes of this research were divided into two parts: (1) to determine the drying characteristics and quality of parboiled paddy undergoing vibratory bed assisted infrared (VIR) drying, and (2) to study the stability of rice bran from the VIR-dried parboiled paddy. Infrared (IR) drying and hot air (HA) drying were applied for comparison purpose. For the experiment 1, VIR drying of parboiled paddy provided the best drying characteristics with the shortest drying time of 50 min and the maximum drying rate of 0.00146 g water/g dry matter·min. VIR drying also produced the greatest head rice yield of 61.3%. The experiment 2 presented that rice bran from VIR-dried parboiled paddy had the highest oil content of 0.256 ± 0.041 g/g dry matter and the most stable in term of minimum change in free fatty acid (FFA) content. The increase in FFA during storage for 14 days was 0.36%. However, the increases in FFA of rice bran from IR-and HA-dried parboiled rice and normal rice were 0.38, 1.36, and 4.10%, respectively.

scholarly journals Effect of hot air assisted infrared drying on drying characteristics and quality of rice bran pellets

2018 ◽  
Vol 192 ◽  
pp. 03040 ◽  
Author(s):  
Sahachart Sansak ◽  
Jiraporn Sripinyowanich Jongyingcharoen
Keyword(s):  
Air Temperature ◽  
Rice Bran ◽  
Oil Content ◽  
Reference Sample ◽  
Moisture Diffusivity ◽  
Drying Time ◽  
Drying Characteristics ◽  
Hot Air ◽  
Different Levels

The objective of this study was to determine drying characteristics and quality of rice bran pellet subjected to hot air assisted infrared (HA-IR) drying at different levels of infrared (IR) intensity (750 – 3750 W/m2) and air temperature (40 – 80°C). The rice bran pellets were dried from 0.18 to 0.08 g water/g dry matter. The maximum drying rate (DR) and drying time were in the ranges of 0.0030 – 0.0165 g water/g dry matter·min and 8 – 54 min, respectively. Higher IR intensity and air temperature resulted in greater maximum DR and shorter drying time. The same trend was also observed for the effective moisture diffusivity (Deff) values which were between 0.3103×10-7 and 2.7603×10-7 m2/s. As compared to the commercial reference sample of dried rice bran pellets, the products of this study had higher oil content and lower FFA content. The oil content was affected by IR intensity only while the FFA content was affected both by IR intensity and air temperature. HA-IR drying could improve drying characteristics of the rice bran pellets and produce better quality of the dried products.

Effect of Pre-Treatments and Drying Air Temperature on the Quality of Dehydrated Oyster Mushroom (Pleurotus Florida)

2019 ◽  
Vol 56 (1) ◽  
pp. 34
Author(s):  
Parul Bora ◽  
Asha Kawatra
Keyword(s):  
Citric Acid ◽  
Oyster Mushroom ◽  
Drying Methods ◽  
Rehydration Ratio ◽  
Drying Time ◽  
Drying Characteristics ◽  
Drying Temperature ◽  
Hot Air ◽  
Adverse Influence

<em>Experiments were conducted on pre treated dehydrated oyster mushroom with steeping in citric acid and sodium chloride and blanching to investigate the effect of pre treatments and drying methods on drying characteristics of mushroom and quality of dried oyster mushroom. Drying was accomplished in a cabinet dryer using hot air at 40<sup>O </sup>C, 60<sup>O</sup>C and by sun drying. The drying characteristics of mushroom were not affected by the pre-treatments significantly. However, the rate of drying increased with the increase in drying temperature. Increase in drying temperature significantly reduced the total drying time. Pre treatments and drying temperature had adverse influence on the rehydration ratio, hardness and colour of the dehydrated mushrooms. Blanching improves the colour of the dehydrated mushroom but increased hardness also. A loss of protein was observed during blanching</em>

scholarly journals Ultrasound-Enhanced Hot Air Drying of Germinated Highland Barley Seeds: Drying Characteristics, Microstructure, and Bioactive Profile

2019 ◽  
Vol 1 (4) ◽  
pp. 496-510
Author(s):  
Yan Song ◽  
Yang Tao ◽  
Xiaoyu Zhu ◽  
Yongbin Han ◽  
Pau Loke Show ◽  
...  
Keyword(s):  
Phenolic Content ◽  
Original Structure ◽  
Hot Air Drying ◽  
Drying Time ◽  
Air Drying ◽  
Drying Characteristics ◽  
Organic Selenium ◽  
Hot Air ◽  
Highland Barley

The effects of ultrasound-enhanced hot air drying on the drying characteristics, microstructure and bioactive profile of germinated highland barley seeds (GHB) were studied. GHB was dried by hot air at 55 °C and 70 °C and ultrasonic intensities of 125.1 W/dm2 and 180.2 W/dm2, respectively. The results showed that when the drying temperature was 55 °C or 70 °C, the sonicated groups could shorten the drying time by 17.4–26.1% or 18.8–31.3%, respectively. Ultrasound drying at 125.1 W/dm2 and 55 °C could mostly increase the content of organic selenium and the rehydration rate, improve the color and maintain the original structure of GHB. Compared with hot air drying alone, the phenolic content did not increase due to ultrasound-enhanced hot air drying. Therefore, drying at an ultrasonic intensity of 125.1 W/dm2 and a temperature of 55 °C could effectively shorten the drying time, and enhance the quality of GHB.

scholarly journals The Optimization and Mathematical Modeling of Quality Attributes of Parboiled Rice Using a Response Surface Method

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Khurram Yousaf ◽  
Chen Kunjie ◽  
Chen Cairong ◽  
Adnan Abbas ◽  
Yuping Huang ◽  
...  
Keyword(s):  
Response Surface ◽  
Rice Variety ◽  
Quality Parameters ◽  
Cooking Time ◽  
Soaking Time ◽  
Parboiled Rice ◽  
Surface Method ◽  
Head Rice ◽  
Soaking Temperature

The response surface methodology was used to optimize the hydrothermal processing conditions based on the rice quality parameters of the Rong Youhua Zhan rice variety (Indica). The effect of soaking temperature (29.77, 40, 55, 70, and 80.23°C), soaking time (67.55, 90, 120, 150, and 170.45 min), and steaming time (1.59, 5, 10, 15, and 18.41 min), each tested at five levels, on percentage of head rice yield (HRY), hardness, cooking time, lightness, and color were determined, with R2 values of 0.96, 0.94, 0.90, 0.88, and 0.94, respectively. HRY, hardness, cooking time, and color increased with process severity while lightness decreased, although HRY decreased after reaching a maximum. The predicted optimum soaking temperature, soaking time, and steaming time were 69.88°C, 150 min, and 6.73 min, respectively, and the predicted HRY, hardness, cooking time, lightness, and color under these conditions were 73.43%, 29.95 N, 32.14 min, 83.03 min, and 12.24 min, respectively, with a composite desirability of 0.9658. The parboiling industry could use the findings of the current study to obtain the desired quality of parboiled rice. This manuscript will be helpful for researchers working on commercializing parboiled rice processes in China as well as in other countries.

scholarly journals Effect of temperature and mode of drying on bioactive compounds and quality of germinated parboiled rice

2018 ◽  
Author(s):  
Busarakorn Mahayothee ◽  
Supaporn Klaykruayat ◽  
Marcus Nagle ◽  
Joachim Müller
Keyword(s):  
Bioactive Compounds ◽  
Rice Yield ◽  
Aminobutyric Acid ◽  
Flow Mode ◽  
Gamma Aminobutyric Acid ◽  
Parboiled Rice ◽  
Head Rice ◽  
Through Flow ◽  
Head Rice Yield

Germinated parboiled rice (GPR) is recognized as a functional food because it is rich in bioactive compounds, especially gamma-aminobutyric acid (GABA). GPR was produced by soaking, incubating, steaming, and then drying using a high-precision hot air dryer. The results indicated that air flow mode and drying temperature had significant effects on the quality of GPR. Drying at higher temperatures and shorter times conserved GABA content. Using through-flow mode decreased drying time and prevented color change. However, a slightly lower percentage of head rice yield was observed. Moreover, using through-flow mode negatively affected the hardness loss after cooking.Keywords: Germinated parboiled rice; Drying mode; Gamma-aminobutyric acid; Head rice yield  

scholarly journals Examination of physical properties of final product and drying properties of combined (convective pre-drying and freeze finish-drying) dehydration method

2014 ◽  
pp. 5-12
Author(s):  
Tamás Antal
Keyword(s):  
Freeze Drying ◽  
Operating Conditions ◽  
Small Scale ◽  
Case Hardening ◽  
Degree Polynomial ◽  
Hot Air Drying ◽  
Drying Time ◽  
Drying Characteristics ◽  
Hot Air ◽  
Drying Properties

In this study, the effects of freeze drying (FD), hot-air drying (HAD) and combined drying (HAD-FD) on drying characteristics, energy uptake, texture, rehydration and color of carrot were investigated. Results showed that HAD-FD significantly improved the drying time compared with FD under the same operating conditions, and the HAD-FD can reduce the total cost of dehydration. The drying kinetics was described by the Henderson-Pabis and the third degree polynomial models in the case of HAD, FD and HAD-FD. The HAD carrot samples were exhibited shrinkage, case hardening, poor rehydration and brown surface. The FD carrot cubes appeared porous structure, excellent rehydration, soft texture and loose color. The HAD-FD samples were superior to HAD products and was nearer in quality to FD products with respect to appearance, rehydration and surface resistance (texture). Finally, it is concluded that HAD-FD is effective in improving the FD drying rate. However, the combined drying has a small-scale adverse effect on product quality.

scholarly journals Drying Modelling, Moisture Diffusivity and Sensory quality of Thin Layer dried Beef

2018 ◽  
Vol 6 (2) ◽  
pp. 552-565 ◽  
Author(s):  
Eunice Akello Mewa ◽  
Michael Wandayi Okoth ◽  
Catherine Nkirote Kunyanga ◽  
Musa Njue Rugiri
Keyword(s):  
Thin Layer ◽  
Sensory Quality ◽  
Moisture Diffusivity ◽  
Drying Kinetics ◽  
Effect Of Temperature ◽  
Slice Thickness ◽  
Drying Time ◽  
Drying Characteristics ◽  
Thin Layer Drying

The objective of the present study was to determine the drying kinetics, moisture diffusivity and sensory quality of convective air dried beef. The effect of temperature of drying (30-60°C) and thickness of samples (2.5-10 mm) on the convective thin-layer drying kinetics of beefdried in a cabinet dryer was evaluated. Five semi-theoretical models were fit to the drying experimentaldata with the aim of predicting drying characteristics of beef and fitting quality of models determined using the standard error of estimate (SEE)and coefficient of determination (R2). Determination ofeffective moisture diffusivity (Deff) from the experimental drying datawas done and sensory quality of the optimized dried cooked and uncookedbeef samplesevaluated. Drying time and rate of drying increased with an increasing temperature but decreased with increased slice thickness. However, there was overlapping of drying curves at 40-50°C. Among the selected models, Page model gave the best prediction of beef drying characteristics. Effective moisture diffusivity (Deff) ranged between 4.2337 x 10-11 and 5.5899 x 10-10 m2/s, increasing with an increase in air temperature and beef slice thickness.Of all the sensory parameters evaluated, texture was the only attribute that gave significantly different (P > 0.05) scores between the cooked and uncooked dried beef samples.

Effects of drying methods on color retention and chlorophyll of celery (ApiumgraveolensL.), spinach (Spinacia oleraceaL.), Malabar spinach (Basella albaL.)

2020 ◽  
pp. 53-61
Author(s):  
Dat Q Tran
Keyword(s):  
Microwave Drying ◽  
Drying Methods ◽  
Hot Air Drying ◽  
Drying Time ◽  
Air Drying ◽  
Color Retention ◽  
Hot Air ◽  
Drying Techniques ◽  
Dried Vegetables

Dried vegetables are considered convenient for storage, transportation and preservation. The different drying techniques could influence the quality of resulting products. This study aimed to evaluate the effects of three distinguish drying methods as hot-air drying, foam-mat drying and microwave drying on the color retention and chlorophyll of green vegetables powder. Fresh spinach(Spinacia oleraceaL.), celery (Apium graveolensL.), Malabar spinach (Basella albaL.) were dried by different methods: hot air at 60oC, foam-mat at 60oC and microwave at 270 W until the samples reached approximately 9% of moisture content (wb). The drying time of the dried samples by microwave, foam-mat and hot-air method were 60, 210 and 240 min, respectively. Foam-mat dried vegetables were found to have the best quality in terms of color and the residual chlorophyll content. The findings suggest that foam-mat drying is promising in dried vegetable processing

scholarly journals Infrared Drying as a Quick Preparation Method for Dried Tangerine Peel

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Mingyue Xu ◽  
Guifang Tian ◽  
Chengying Zhao ◽  
Aftab Ahmad ◽  
Huijuan Zhang ◽  
...  
Keyword(s):  
Radical Scavenging ◽  
Short Wave ◽  
Hot Air Drying ◽  
Time Saving ◽  
Drying Time ◽  
Infrared Drying ◽  
Sun Drying ◽  
Hot Air ◽  
Short Wave Infrared ◽  
Dpph Radical Scavenging

To establish the most convenient and effective method to dry tangerine peels, different methods (sun drying, hot-air drying, freeze drying, vacuum drying, and medium- and short-wave infrared drying) were exploited. Our results indicated that medium- and short-wave infrared drying was the best method to preserve nutraceutical components; for example, vitamin C was raised to 6.77 mg/g (D.W.) from 3.39 mg/g (sun drying). Moreover, the drying time can be shortened above 96% compared with sun drying. Importantly, the efficiency of DPPH radical scavenging was enhanced from 26.66% to 55.92%. These findings would provide a reliable and time-saving methodology to produce high-quality dried tangerine peels.

Experiments on Hot-Air and Infrared Drying Characteristics of LiCoO2 Cathode Coating for Lithium-Ion Battery

2020 ◽  
Vol 1003 ◽  
pp. 260-267
Author(s):  
Xian Feng Wu ◽  
Xu Jia Li ◽  
Xin Zhi Bei
Keyword(s):  
Lithium Ion Battery ◽  
Radiation Power ◽  
Influencing Factor ◽  
Lithium Ion ◽  
Drying Time ◽  
Infrared Drying ◽  
Hot Air ◽  
Constant Rate ◽  
Drying Conditions ◽  
Drying Efficiency

Based on the drying technology principle of lithium-ion battery cathode coating, the variation law of dry base moisture content and drying rate in the process of hot-air drying and infrared drying was studied. The experimental results show that the cathode coating of lithium-ion battery dried under hot-air and infrared conditions can be divided into three stages: increasing-rate, constant-rate, and falling-rate. The constant-rate stage is the main drying stage, accounting for more than 50% of the weight loss, the falling-rate stage is the main energy consumption stage, accounting for more than 50% of the time. Under the condition of hot-air, the change level of airspeed is the main influencing factor of the drying process, and the drying time can be reduced by about 35% for each 0.7 m/s increase in airspeed. Under infrared conditions, the change level of radiation power is the main influencing factor of the drying process, and the drying time can be reduced by about 34.1% for every 100W of power increase. The optimal drying conditions under hot-air conditions are: air temperature 90 °C, airspeed 2.3 m/s; the optimal drying conditions under infrared conditions are: radiation distance 13 cm, radiation power 200 W. By comparing the best conditions of hot-air and infrared, it can be known that the drying efficiency is higher in the infrared condition and the drying duration is 160 s, but the energy utilization rate in the falling-rate stage in the infrared condition is lower than that in the hot-air condition. Therefore, when infrared drying enters the falling-rate stage, it can be supplemented by hot-air drying to further improve the drying efficiency.

Sign in / Sign up

Export Citation Format

Share Document