Reverse Micro-Emulsion Synthesis of Oxygen-Enriched Low-Friction Boron Nitride/Calcium Borate Microspheres

2018 ◽  
Vol 71 (12) ◽  
pp. 983
Author(s):  
Songdong Yuan ◽  
Canxing Yang ◽  
Xing Zhu ◽  
Guodong Jiang ◽  
Renzhong Huang ◽  
...  
Keyword(s):  
Boron Nitride ◽  
Photoelectron Spectroscopy ◽  
Sodium Borate ◽  
Phase Identification ◽  
Calcium Borate ◽  
Base Oil ◽  
X Ray ◽  
Transmission Electron ◽  
Micro Emulsion ◽  
Boron Source

Oxygen enriched boron nitride microspheres (BNOs) coated with nano-sized calcium borate (CB) were synthesised by a reverse micro-emulsion method, in which calcium chloride and sodium borate were selected as the calcium and boron source, respectively. The phase identification and chemical bonding of the composite were confirmed by X-ray driffraction (XRD) and FT-IR spectroscopy. The chemical composition and valence state were determined by X-ray photoelectron spectroscopy (XPS). The morphology and microstructure of the samples were characterised by transmission electron microscopy (TEM) along with surface area analysis. The tribological property of the microspheres as a wear resistance additive in base oil was evaluated by a four-ball tester. The results show that the strawberry-like BNO/CB nanocomposites were fabricated successfully and possess a relatively high friction-reducing and antiwear performance. After the addition of BNO/CB nanocomposites, the friction coefficients of the base oil decreased by 13.3% while the diameter of the grinding spot decreased by 16.4%.

Preparation, Characterization and Tribological Evaluation of Calcium Borate Nanoparticles as Lubricant Additives

2010 ◽  
Vol 148-149 ◽  
pp. 1047-1056 ◽  
Author(s):  
Jiu Sheng Li ◽  
Li Feng Hao ◽  
Xiao Hong Xu ◽  
Li Zhang ◽  
Tian Hui Ren
Keyword(s):  
Oleic Acid ◽  
Electron Microscope ◽  
Photoelectron Spectroscopy ◽  
Lubricant Additive ◽  
Calcium Borate ◽  
Action Mechanism ◽  
Friction Process ◽  
X Ray ◽  
Transmission Electron ◽  
Worn Surface

To develop a potential substitute for conventional lubricant additive, pure calcium borate nanoparticles (PCBN) and calcium borate nanoparticles modified with oleic acid (MCBN) were prepared. The microstructures of the as-obtained samples were characterized using X-ray power diffraction (XRD), transmission electron microscope (TEM) and infrared spectra (IR), and the dispersing stability of oil containing nanoparticles was also evaluated. Tribological properties of MCBN used as lubricating additive were evaluated using four-ball tribometer and compared with that of PCBN. The results indicate that MCBN show better antiwear and friction-reducing property than PCBN. The worn surface of the steel ball lubricated with MCBN was investigated by Polarized microscope (PM) and X-ray photoelectron spectroscopy (XPS), and the action mechanism of MCBN during friction process was preliminarily discussed.

scholarly journals α-Cellulose Fibers of Paper-Waste Origin Surface-Modified with Fe3O4 and Thiolated-Chitosan for Efficacious Immobilization of Laccase

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 581
Author(s):  
Gajanan S. Ghodake ◽  
Surendra K. Shinde ◽  
Ganesh D. Saratale ◽  
Rijuta G. Saratale ◽  
Min Kim ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Photoelectron Spectroscopy ◽  
Cellulose Fibers ◽  
Relative Activity ◽  
Significant Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Laccase Immobilization ◽  
Surface Modified

The utilization of waste-paper-biomass for extraction of important α-cellulose biopolymer, and modification of extracted α-cellulose for application in enzyme immobilization can be extremely vital for green circular bio-economy. Thus, in this study, α-cellulose fibers were super-magnetized (Fe3O4), grafted with chitosan (CTNs), and thiol (-SH) modified for laccase immobilization. The developed material was characterized by high-resolution transmission electron microscopy (HR-TEM), HR-TEM energy dispersive X-ray spectroscopy (HR-TEM-EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses. Laccase immobilized on α-Cellulose-Fe3O4-CTNs (α-Cellulose-Fe3O4-CTNs-Laccase) gave significant activity recovery (99.16%) and laccase loading potential (169.36 mg/g). The α-Cellulose-Fe3O4-CTNs-Laccase displayed excellent stabilities for temperature, pH, and storage time. The α-Cellulose-Fe3O4-CTNs-Laccase applied in repeated cycles shown remarkable consistency of activity retention for 10 cycles. After the 10th cycle, α-Cellulose-Fe3O4-CTNs possessed 80.65% relative activity. Furthermore, α-Cellulose-Fe3O4-CTNs-Laccase shown excellent degradation of pharmaceutical contaminant sulfamethoxazole (SMX). The SMX degradation by α-Cellulose-Fe3O4-CTNs-Laccase was found optimum at incubation time (20 h), pH (3), temperatures (30 °C), and shaking conditions (200 rpm). Finally, α-Cellulose-Fe3O4-CTNs-Laccase gave repeated degradation of SMX. Thus, this study presents a novel, waste-derived, highly capable, and super-magnetic nanocomposite for enzyme immobilization applications.

scholarly journals Novel Carbon Dots Derived from Glycyrrhizae Radix et Rhizoma and Their Anti-Gastric Ulcer Effect

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1512
Author(s):  
Yuhan Liu ◽  
Meiling Zhang ◽  
Jinjun Cheng ◽  
Yue Zhang ◽  
Hui Kong ◽  
...  
Keyword(s):  
Gastric Ulcer ◽  
Photoelectron Spectroscopy ◽  
Carbon Dots ◽  
High Performance ◽  
Raw264.7 Cells ◽  
Mice Model ◽  
X Ray ◽  
Glycyrrhizae Radix ◽  
Transmission Electron ◽  
High Resolution Tem

Glycyrrhizae Radix et Rhizoma (GRR) is one of the commonly used traditional Chinese medicines in clinical practice, which has been applied to treat digestive system diseases for hundreds of years. GRR is preferred for anti-gastric ulcer, however, the main active compounds are still unknown. In this study, GRR was used as precursor to synthesize carbon dots (CDs) by a environment-friendly one-step pyrolysis process. GRR-CDs were characterized by using transmission electron microscopy, high-resolution TEM, fourier transform infrared, ultraviolet-visible and fluorescence spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and high-performance liquid chromatography. In addition, cellular toxicity of GRR-CDs was studied by using CCK-8 in RAW264.7 cells, and the anti-gastric ulcer activity was evaluated and confirmed using mice model of acute alcoholic gastric ulcer. The experiment confirmed that GRR-CDs were the spherical structure with a large number of active groups on the surface and their particle size ranged from 2 to 10 nm. GRR-CDs had no toxicity to RAW264.7 cells at concentration of 19.5 to 5000 μg/mL and could reduce the oxidative damage of gastric mucosa and tissues caused by alcohol, as demonstrated by restoring expression of malondialdehyde, superoxide dismutase and nitric oxide in serum and tissue of mice. The results indicated the explicit anti-ulcer activity of GRR-CDs, which provided a new insights for the research on effective material basis of GRR.

Highly active carbon nanotube–promoted Rh-Mn-Li/SiO2 catalysts for the synthesis of C2+ oxygenates from syngas

2021 ◽  
pp. 174751982098472
Author(s):  
Jun Yu ◽  
Ying Han ◽  
Guoqing Chen ◽  
Xiuzhen Xiao ◽  
Haifang Mao ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Co Hydrogenation ◽  
X Ray ◽  
Highly Active ◽  
Transmission Electron ◽  
Co Insertion ◽  
Temperature Programmed Surface Reaction ◽  
Temperature Programmed ◽  
Oxygenate Synthesis

The effect of carbon nanotubes on the catalytic properties of Rh-Mn-Li/SiO2 catalysts was investigated for CO hydrogenation. The catalysts were comprehensively characterized by means of X-ray power diffraction, N2 sorption, transmission electron microscope, H2–temperature-programmed reduction, CO–temperature-programmed desorption, temperature-programmed surface reaction, and X-ray photoelectron spectroscopy. The results showed that an appropriate amount of carbon nanotubes can be attached to the surface of the SiO2 sphere and can improve the Rh dispersion. Moderate Rh-Mn interaction can be obtained by doping with the appropriate amount of carbon nanotubes, which promotes the formation of strongly adsorbed CO and facilitates the progress of CO insertion, resulting in the increase in the selectivity of C2+ oxygenate synthesis.

scholarly journals Synthesis, characterization and in vitro cytotoxicity study of Co and Ni ferrite nanoparticles prepared by sol-gel method

2021 ◽  
Vol 3 (7) ◽  
Author(s):  
Alexandre Pancotti ◽  
Dener Pereira Santos ◽  
Dielly Oliveira Morais ◽  
Mauro Vinícius de Barros Souza ◽  
Débora R. Lima ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Test Sample ◽  
In Vitro Cytotoxicity ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Transmission Electron ◽  
Crystallite Sizes

AbstractIn this study, we report the synthesis and characterization of NiFe2O4 and CoFe2O4 nanoparticles (NPs) which are widely used in the biomedical area. There is still limited knowledge how the properties of these materials are influenced by different chemical routes. In this work, we investigated the effect of heat treatment over cytotoxicity of cobalt and niquel ferrites NPs synthesized by sol-gel method. Then the samples were studied using transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), Fourier Transform Infrared Spectroscopy Analysis (FTIR), and X-ray fluorescence (XRF). The average crystallite sizes of the particles were found to be in the range of 20–35 nm. The hemocompatibility (erythrocytes and leukocytes) was checked. Cytotoxicity results were similar to those of the control test sample, therefore suggesting hemocompatibility of the tested materials.

scholarly journals Surface Stoichiometry and Depth Profile of Tix-CuyNz Thin Films Deposited by Magnetron Sputtering

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3191
Author(s):  
Arun Kumar Mukhopadhyay ◽  
Avishek Roy ◽  
Gourab Bhattacharjee ◽  
Sadhan Chandra Das ◽  
Abhijit Majumdar ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Film Surface ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
Relative Composition ◽  
Transmission Electron ◽  
Deposited Film ◽  
Deposited Films

We report the surface stoichiometry of Tix-CuyNz thin film as a function of film depth. Films are deposited by high power impulse (HiPIMS) and DC magnetron sputtering (DCMS). The composition of Ti, Cu, and N in the deposited film is investigated by X-ray photoelectron spectroscopy (XPS). At a larger depth, the relative composition of Cu and Ti in the film is increased compared to the surface. The amount of adventitious carbon which is present on the film surface strongly decreases with film depth. Deposited films also contain a significant amount of oxygen whose origin is not fully clear. Grazing incidence X-ray diffraction (GIXD) shows a Cu3N phase on the surface, while transmission electron microscopy (TEM) indicates a polycrystalline structure and the presence of a Ti3CuN phase.

scholarly journals An Insight into Chemistry and Structure of Colloidal 2D-WS2 Nanoflakes: Combined XPS and XRD Study

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1969
Author(s):  
Riccardo Scarfiello ◽  
Elisabetta Mazzotta ◽  
Davide Altamura ◽  
Concetta Nobile ◽  
Rosanna Mastria ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Xrd Analysis ◽  
Crystal Habit ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Evaluation ◽  
Rational Understanding ◽  
Structural Inspection

The surface and structural characterization techniques of three atom-thick bi-dimensional 2D-WS2 colloidal nanocrystals cross the limit of bulk investigation, offering the possibility of simultaneous phase identification, structural-to-morphological evaluation, and surface chemical description. In the present study, we report a rational understanding based on X-ray photoelectron spectroscopy (XPS) and structural inspection of two kinds of dimensionally controllable 2D-WS2 colloidal nanoflakes (NFLs) generated with a surfactant assisted non-hydrolytic route. The qualitative and quantitative determination of 1T’ and 2H phases based on W 4f XPS signal components, together with the presence of two kinds of sulfur ions, S22− and S2−, based on S 2p signal and related to the formation of WS2 and WOxSy in a mixed oxygen-sulfur environment, are carefully reported and discussed for both nanocrystals breeds. The XPS results are used as an input for detailed X-ray Diffraction (XRD) analysis allowing for a clear discrimination of NFLs crystal habit, and an estimation of the exact number of atomic monolayers composing the 2D-WS2 nanocrystalline samples.

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

Characterization of columns grown during KrF laser micromachining of Al2O3–TiC ceramics

2003 ◽  
Vol 18 (5) ◽  
pp. 1123-1130 ◽  
Author(s):  
V. Oliveira ◽  
R. Vilar
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Laser Pulses ◽  
Formation Mechanisms ◽  
X Ray ◽  
Reducing Conditions ◽  
Transmission Electron ◽  
Column Formation ◽  
Krf Laser

This paper aims to contribute to the understanding of column formation mechanisms in Al2O3–TiC ceramics micromachined using excimer lasers. Chemical and structural characterization of columns grown in Al2O3–TiC composite processed with 200 KrF laser pulses at 10 J/cm2 was carried out by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, and x-ray diffraction analysis. Fully developed columns consist of a core of unprocessed material surrounded by an outer layer of Al2TiO5, formed in oxidizing conditions, and an inner layer, formed in reducing conditions, composed of TiC and Al3Ti or an AlTi solid solution. Possible mechanisms of column formation are discussed.

Sign in / Sign up

Export Citation Format

Share Document