Simulation of the interaction between nonspherical particles within the CFD–DEM framework via multisphere approximation and rolling resistance method

2015 ◽  
Vol 34 (4) ◽  
pp. 381-391 ◽  
Author(s):  
Siamak Akhshik ◽  
Mehdi Behzad ◽  
Majid Rajabi
Keyword(s):  
Rolling Resistance ◽  
Nonspherical Particles ◽  
Resistance Method

Total Tire Energy Loss Comparison by the Whole Tire Hysteresis and the Rolling Resistance Methods

1995 ◽  
Vol 23 (4) ◽  
pp. 256-265 ◽  
Author(s):  
P. S. Pillai
Keyword(s):  
Energy Loss ◽  
Rolling Resistance ◽  
Hysteresis Loss ◽  
Basic Premise ◽  
Resistance Method

Abstract Energy loss per hour in a tire traveling at 80 km/h was obtained for a number of tires of different sizes and makes from the respective whole tire hysteresis loss of each tire. This loss value was then compared to the corresponding rolling loss obtained from the 1.7 m dynamometer rolling resistance method. The two methods agreed, indicating that the basic premise of the rolling resistance hysteresis ratio relation is valid.

Extraction and identification of fillers and pigments from pyrolyzed rubber and tire samples

1996 ◽  
Vol 54 ◽  
pp. 174-175
Author(s):  
P. Sadhukhan ◽  
J. B. Zimmerman
Keyword(s):  
Zinc Oxide ◽  
Electron Microscope ◽  
Carbon Black ◽  
Natural Rubber ◽  
Transmission Electron Microscope ◽  
Rolling Resistance ◽  
Synthetic Polymers ◽  
Nitrogen Atmosphere ◽  
Transmission Electron ◽  
Curing Agents

Rubber stocks, specially tires, are composed of natural rubber and synthetic polymers and also of several compounding ingredients, such as carbon black, silica, zinc oxide etc. These are generally mixed and vulcanized with additional curing agents, mainly organic in nature, to achieve certain “designing properties” including wear, traction, rolling resistance and handling of tires. Considerable importance is, therefore, attached both by the manufacturers and their competitors to be able to extract, identify and characterize various types of fillers and pigments. Several analytical procedures have been in use to extract, preferentially, these fillers and pigments and subsequently identify and characterize them under a transmission electron microscope.Rubber stocks and tire sections are subjected to heat under nitrogen atmosphere to 550°C for one hour and then cooled under nitrogen to remove polymers, leaving behind carbon black, silica and zinc oxide and 650°C to eliminate carbon blacks, leaving only silica and zinc oxide.

Tire-Road Interactions — Harmony or Conflict?

1989 ◽  
Vol 17 (1) ◽  
pp. 66-84
Author(s):  
A. R. Williams
Keyword(s):  
Rolling Resistance ◽  
Major Effect ◽  
Road Surface ◽  
Interactive Effects ◽  
Central Theme ◽  
Water Drainage ◽  
The Road ◽  
Truck Tires ◽  
Road Surfaces ◽  
Tire Wear

Abstract This is a summary of work by the author and his colleagues, as well as by others reported in the literature, that demonstrate a need for considering a vehicle, its tires, and the road surface as a system. The central theme is interaction at the footprint, especially that of truck tires. Individual and interactive effects of road and tires are considered under the major topics of road aggregate (macroscopic and microscopic properties), development of a novel road surface, safety, noise, rolling resistance, riding comfort, water drainage by both road and tire, development of tire tread compounds and a proving ground, and influence of tire wear on wet traction. A general conclusion is that road surfaces have both the major effect and the greater potential for improvement.

Tread Depth Effects on Tire Rolling Resistance

2001 ◽  
Vol 29 (3) ◽  
pp. 134-154 ◽  
Author(s):  
J. R. Luchini ◽  
M. M. Motil ◽  
W. V. Mars
Keyword(s):  
Finite Element Analysis ◽  
Common Knowledge ◽  
Rolling Resistance ◽  
Test Method ◽  
Tire Model ◽  
Element Analysis ◽  
Truck Tires ◽  
The Finite Element Analysis ◽  
Equilibrium Test ◽  
Depth Effects

Abstract This paper discusses the measurement and modeling of tire rolling resistance for a group of radial medium truck tires. The tires were subjected to tread depth modifications by “buffing” the tread surface. The experimental work used the equilibrium test method of SAE J-1269. The finite element analysis (FEA) tire model for tire rolling resistance has been previously presented. The results of the testing showed changes in rolling resistance as a function of tread depth that were inconsistent between tires. Several observations were also inconsistent with published information and common knowledge. Several mechanisms were proposed to explain the results. Additional experiments and models were used to evaluate the mechanisms. Mechanisms that were examined included tire age, surface texture, and tire shape. An explanation based on buffed tread radius, and the resulting changes in footprint stresses, is proposed that explains the observed experimental changes in rolling resistance with tread depth.

Application of Computational Mechanics to Tire Design—Yesterday, Today, and Tomorrow

2011 ◽  
Vol 39 (4) ◽  
pp. 223-244 ◽  
Author(s):  
Y. Nakajima
Keyword(s):  
Finite Element ◽  
New Technologies ◽  
Computational Mechanics ◽  
Design Procedure ◽  
Side Wall ◽  
Rolling Resistance ◽  
Optimization Techniques ◽  
Stress Strain ◽  
Element Analysis ◽  
Crown Shape

Abstract The tire technology related with the computational mechanics is reviewed from the standpoint of yesterday, today, and tomorrow. Yesterday: A finite element method was developed in the 1950s as a tool of computational mechanics. In the tire manufacturers, finite element analysis (FEA) was started applying to a tire analysis in the beginning of 1970s and this was much earlier than the vehicle industry, electric industry, and others. The main reason was that construction and configurations of a tire were so complicated that analytical approach could not solve many problems related with tire mechanics. Since commercial software was not so popular in 1970s, in-house axisymmetric codes were developed for three kinds of application such as stress/strain, heat conduction, and modal analysis. Since FEA could make the stress/strain visible in a tire, the application area was mainly tire durability. Today: combining FEA with optimization techniques, the tire design procedure is drastically changed in side wall shape, tire crown shape, pitch variation, tire pattern, etc. So the computational mechanics becomes an indispensable tool for tire industry. Furthermore, an insight to improve tire performance is obtained from the optimized solution and the new technologies were created from the insight. Then, FEA is applied to various areas such as hydroplaning and snow traction based on the formulation of fluid–tire interaction. Since the computational mechanics enables us to see what we could not see, new tire patterns were developed by seeing the streamline in tire contact area and shear stress in snow in traction.Tomorrow: The computational mechanics will be applied in multidisciplinary areas and nano-scale areas to create new technologies. The environmental subjects will be more important such as rolling resistance, noise and wear.

Rolling Resistance Calculation Procedure Using the Finite Element Method

2019 ◽  
Vol 48 (3) ◽  
pp. 224-248
Author(s):  
Pablo N. Zitelli ◽  
Gabriel N. Curtosi ◽  
Jorge Kuster
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Rolling Resistance ◽  
Element Model ◽  
The Finite Element Method ◽  
Temperature Changes ◽  
Rubber Compounds ◽  
Different Temperatures ◽  
Materials Used ◽  
Account Temperature

ABSTRACT Tire engineers are interested in predicting rolling resistance using tools such as numerical simulation and tests. When a car is driven along, its tires are subjected to repeated deformation, leading to energy dissipation as heat. Each point of a loaded tire is deformed as the tire completes a revolution. Most energy dissipation comes from the cyclic loading of the tire, which causes the rolling resistance in addition to the friction force in the contact patch between the tire and road. Rolling resistance mainly depends on the dissipation of viscoelastic energy of the rubber materials used to manufacture the tires. To obtain a good rolling resistance, the calculation method of the tire finite element model must take into account temperature changes. It is mandatory to calibrate all of the rubber compounds of the tire at different temperatures and strain frequencies. Linear viscoelasticity is used to model the materials properties and is found to be a suitable approach to tackle energy dissipation due to hysteresis for rolling resistance calculation.

Formation of Standing Waves in Radial Tires

1984 ◽  
Vol 12 (1) ◽  
pp. 44-63 ◽  
Author(s):  
Y. D. Kwon ◽  
D. C. Prevorsek
Keyword(s):  
High Speed ◽  
Critical Speed ◽  
Unit Length ◽  
Standing Waves ◽  
Rolling Resistance ◽  
Damping Coefficient ◽  
Circular Membrane ◽  
Critical Speeds ◽  
Steel Cord ◽  
The Individual

Abstract Radial tires for automobiles were subjected to high speed rolling under load on a testing wheel to determine the critical speeds at which standing waves started to form. Tires of different makes had significantly different critical speeds. The damping coefficient and mass per unit length of the tire wall were measured and a correlation between these properties and the observed critical speed of standing wave formation was sought through use of a circular membrane model. As expected from the model, desirably high critical speed calls for a high damping coefficient and a low mass per unit length of the tire wall. The damping coefficient is particularly important. Surprisingly, those tire walls that were reinforced with steel cord had higher damping coefficients than did those reinforced with polymeric cord. Although the individual steel filaments are elastic, the interfilament friction is higher in the steel cords than in the polymeric cords. A steel-reinforced tire wall also has a higher density per unit length. The damping coefficient is directly related to the mechanical loss in cyclic deformation and, hence, to the rolling resistance of a tire. The study shows that, in principle, it is more difficult to design a tire that is both fuel-efficient and free from standing waves when steel cord is used than when polymeric cords are used.

Evolving the Banded Radial Tire

1987 ◽  
Vol 15 (1) ◽  
pp. 30-41 ◽  
Author(s):  
E. G. Markow
Keyword(s):  
Finite Element ◽  
Wear Rate ◽  
Finite Element Modeling ◽  
Laboratory Tests ◽  
Rolling Resistance ◽  
Two Dimensional ◽  
Theoretical Discussion ◽  
Radial Tire ◽  
Puncture Resistance ◽  
Element Modeling

Abstract Development of the banded radial tire is discussed. A major contribution of this tire design is a reliable run-flat capability over distances exceeding 160 km (100 mi). Experimental tire designs and materials are considered; a brief theoretical discussion of the mechanics of operation is given based on initial two-dimensional studies and later on more complete finite element modeling. Results of laboratory tests for cornering, rolling resistance, and braking are presented. Low rolling resistance, good cornering and braking properties, and low tread wear rate along with good puncture resistance are among the advantages of the banded radial tire designs.

Sign in / Sign up

Export Citation Format

Share Document