scholarly journals Effect of Geometrical and Chemical Constraints on Water Flux across Artificial Membranes

1971 ◽  
Vol 57 (5) ◽  
pp. 610-622 ◽  
Author(s):  
C. M. Gary-Bobo ◽  
A. K. Solomon
Keyword(s):  
Diffusion Coefficient ◽  
Hydraulic Conductivity ◽  
Water Flux ◽  
Cellulose Triacetate ◽  
Bulk Water ◽  
Kcal Mole ◽  
Cellulose Acetate Membranes ◽  
Water Viscosity ◽  
Apparent Activation Energies ◽  
Geometrical Factors

Studies have been made on the temperature dependence of both the hydraulic conductivity, Lp, and the THO diffusion coefficient, ω, for a series of cellulose acetate membranes (CA) of varying porosity. A similar study was also made of a much less polar cellulose triacetate membrane (CTA). The apparent activation energies, Ea, for diffusion across CA membranes vary with porosity, being 7.8 kcal/mole for the nonporous membrane and 5.5 kcal/mole for the most porous one. Ea for diffusion across the less polar CTA membrane is smaller than Ea for the CA membrane of equivalent porosity. Classical viscous flow, in which the hydraulic conductivity is inversely related to bulk water viscosity, has been demonstrated across membranes with very small equivalent pores. Water-membrane interactions, which depend upon both chemical and geometrical factors are of particular importance in diffusion. The implication of these findings for the interpretation of water permeability experiments across biological membranes is discussed.

scholarly journals Temperature Dependence of Vasopressin Action on the Toad Bladder

1972 ◽  
Vol 59 (5) ◽  
pp. 519-533 ◽  
Author(s):  
Patrick Eggena
Keyword(s):  
Temperature Dependence ◽  
Conformational Changes ◽  
Water Movement ◽  
Water Flux ◽  
Bulk Water ◽  
Energy Of Activation ◽  
Osmotic Gradient ◽  
Kcal Mole ◽  
Osmotic Water ◽  
Apparent Energy Of Activation

Toad bladders were challenged with vasopressin at one temperature, fixed on the mucosa with 1% glutaraldehyde, and then subjected to an osmotic gradient at another temperature. Thus, the temperature dependence of vasopressin action on membrane permeability was distinguished from the temperature dependence of osmotic water flux. As the temperature was raised from 20° to 38°C, there was a substantial increase in the velocity of vasopressin action, but osmotic flux was hardly affected. In this range of temperature the apparent energy of activation for net water movement across the bladder amounted to only 1.2 kcal/mole, a value well below the activation energy for bulk water viscosity. It is suggested that osmotic water flux takes place through narrow, nonpolar channels in the membrane. When the temperature was raised from 4° to 20°C, both vasopressin action as well as osmotic water flux were markedly enhanced. Activation energies for net water movement were now 8.5 kcal/mole (4°–9°C) and 4.1 kcal/mole (9°–20°C), indicating that the components of the aqueous channel undergo conformational changes as the temperature is lowered from 20°C. At 43°C bladder reactivity to vasopressin was lost, and irreversible changes in selective permeability were observed. The apparent energy of activation for net water movement across the denatured membrane was 6.6 kcal/mole. Approximately 1 µosmol of NaCl was exchanged for 1 µl of H2O across the denatured membrane.

Effect of the structure of cellulose acetate membranes on their permeability, electrical conductivity and rejection

1990 ◽  
Vol 55 (12) ◽  
pp. 2933-2939 ◽  
Author(s):  
Hans-Hartmut Schwarz ◽  
Vlastimil Kůdela ◽  
Klaus Richau
Keyword(s):  
Electrical Conductivity ◽  
Electrical Properties ◽  
Cellulose Acetate ◽  
Reverse Osmosis ◽  
Water Flux ◽  
Cellulose Acetate Membrane ◽  
Structure Parameters ◽  
Dc Electrical Conductivity ◽  
Cellulose Acetate Membranes

Ultrafiltration cellulose acetate membrane can be transformed by annealing into reverse osmosis membranes (RO type). Annealing brings about changes in structural properties of the membranes, accompanied by changes in their permeability behaviour and electrical properties. Correlations between structure parameters and electrochemical properties are shown for the temperature range 20-90 °C. Relations have been derived which explain the role played by the dc electrical conductivity in the characterization of rejection ability of the membranes in the reverse osmosis, i.e. rRO = (1 + exp (A-B))-1, where exp A and exp B are statistically significant correlation functions of electrical conductivity and salt permeation, or of electrical conductivity and water flux through the membrane, respectively.

scholarly journals Effect of Modification on the Fluid Diffusion Coefficient in Silica Nanochannels

Molecules ◽  
2021 ◽  
Vol 26 (13) ◽  
pp. 4030
Author(s):  
Gengbiao Chen ◽  
Zhiwen Liu
Keyword(s):  
Diffusion Coefficient ◽  
Diffusion Coefficients ◽  
Surface Effect ◽  
Bulk Water ◽  
Self Diffusion ◽  
Average Diffusion Coefficient ◽  
Average Diffusion ◽  
Chain Lengths ◽  
Fluid Diffusion ◽  
Self Diffusion Coefficient

The diffusion behavior of fluid water in nanochannels with hydroxylation of silica gel and silanization of different modified chain lengths was simulated by the equilibrium molecular dynamics method. The diffusion coefficient of fluid water was calculated by the Einstein method and the Green–Kubo method, so as to analyze the change rule between the modification degree of nanochannels and the diffusion coefficient of fluid water. The results showed that the diffusion coefficient of fluid water increased with the length of the modified chain. The average diffusion coefficient of fluid water in the hydroxylated nanochannels was 8.01% of the bulk water diffusion coefficient, and the diffusion coefficients of fluid water in the –(CH2)3CH3, –(CH2)7CH3, and –(CH2)11CH3 nanochannels were 44.10%, 49.72%, and 53.80% of the diffusion coefficients of bulk water, respectively. In the above four wall characteristic models, the diffusion coefficients in the z direction were smaller than those in the other directions. However, with an increase in the silylation degree, the increased self-diffusion coefficient due to the surface effect could basically offset the decreased self-diffusion coefficient owing to the scale effect. In the four nanochannels, when the local diffusion coefficient of fluid water was in the range of 8 Å close to the wall, Dz was greater than Dxy, and beyond the range of 8 Å of the wall, the Dz was smaller than Dxy.

Functional role of earthworms to control the hydraulic conductivity of constructed wetlands 

2021 ◽  
Author(s):  
Océane Gilibert ◽  
Dan Tam Costa ◽  
Sabine Sauvage ◽  
Didier Orange ◽  
Yvan Capowiez ◽  
...  
Keyword(s):  
Organic Matter ◽  
Hydraulic Conductivity ◽  
Constructed Wetlands ◽  
Hyporheic Zone ◽  
Riparian Zone ◽  
Water Flux ◽  
Sediment Surface ◽  
Deep Soil ◽  
The Impact ◽  
Organic Matter Input

<p>Wetlands are known for their natural service of water quality regulation. The hyporheic zones of the rivers filter and purify the surface water from the stream and infiltrated waters in soil nearby through the riparian zone. This purification service occurs because of a synergy between the substrate and its biodiversity (including plants, bacteria and other invertebrates). Our study deals with constructed wetlands (CW) as a nature-based solution mimicking wetlands water purification process, to purify wastewaters. The REUSE technology of CW is based on the use of specific layers of gravels and sands inside a close concrete structure, planted with specific sub-aquatic plants, where wastewaters or runoff of stormwaters are introduced to be filtered. The technology of Vertical Flow Constructed Wetlands (VFCW) reproduces the water flux observed in the riparian zone with a gravity flow of water. It is composed of reeds planted on a sandy layer (Ø 0-4 mm) and succession of gravel layers. This substrate can be saturated or unsaturated to reproduce the functioning of the hyporheic zone or the riparian zone respectively. By the time, the substrate is colonized by a community of bacteria producing biofilms which capture the residual organic matter from wastewaters to mineralize them. However, the VFCW substrates tend to clog over time due to the accumulation of organic matter and biofilms. Many studies consider earthworms as one of the solutions to alleviate this clogging, thanks to their burrows recreating macropores and preferential channels which help to improve the dispersion of water into the deep soil. The main goal of this study is to assess the impact of earthworm activities on the hydraulic conductivity of columns composed with the same substrate used in the VFCW. Different densities of earthworms (Eisenia fetida) were introduced (0, 100, 500, 1000 g of earthworms/m²) in these columns to be monitored for 37 days. The hydraulic conductivity was measured every 7 days, aside from day 23 with the addition of 40 g of peat bedding on column surfaces to simulate a high organic matter input. Columns with earthworm density superior to 500 g/m² shows an amelioration of their hydraulic conductivity after 21 days. These densities are also able to restore the hydraulic conductivity of the column in less than 7 days after the setting of clogged condition due to the organic matter input (peat bedding) at the sediment surface. This study showed that the burrowing activity of E. fetida improves the hydraulic flux of a sandy substrate and this impact is dependent on the earthworm density introduced. So, the addition of earthworms in the VFCW could serve as a prevention against clogging.</p>

Determination of transport constants of isolated Nitella cell walls

1968 ◽  
Vol 46 (4) ◽  
pp. 317-327 ◽  
Author(s):  
M. T. Tyree
Keyword(s):  
Activation Energy ◽  
Cell Wall ◽  
Diffusion Coefficient ◽  
Cell Walls ◽  
Transport Coefficients ◽  
Irreversible Thermodynamics ◽  
Kcal Mole ◽  
Limiting Value ◽  
Nitella Flexilis

Transport coefficients LPP, LPE, LEP, and LEE for electrokinetic equations according to irreversible thermodynamics, the Onsager coefficients, were measured for isolated Nitella flexilis cell walls in KCl solutions ranging from 10−4 to 100 normal. LPP and LPE (= LEP) were found to be independent of KCl concentration and equal to 1.4 × 10−6 cm3 sec−1 cm−2 (joule cm−3)−1 cm and 6 × 10−5 cm3 sec−1 cm−2 volt−1 cm respectively. LEE was a function of the salt concentration, reaching a limiting value of about 1.2 × 10−3 mho cm−1 in 10−4 N KCl. The activation energy for movement of KCl in cell walls was found to be 4.33 Kcal mole−1; the diffusion coefficient for KCl in cell walls was calculated by two methods to be 8 × 10−6 cm2 sec−1; and the concentration of the fixed ions in Nitella cell walls from the above data was estimated at greater than 0.04 equivalent per liter of cell wall. Electroosmosis in Nitella membranes is re-examined in the light of the measured transport coefficients and it is concluded that under proper conditions the cell wall of Nitella can contribute significantly (~20% or more) to the observed electroosmosis of living Nitella cells.

scholarly journals WATER TRANSPORT IN INVERTEBRATE PERIPHERAL NERVE FIBERS

1958 ◽  
Vol 41 (5) ◽  
pp. 927-958 ◽  
Author(s):  
Arnold H. Nevis
Keyword(s):  
Peripheral Nerve ◽  
Arrhenius Equation ◽  
Tritiated Water ◽  
Water Flux ◽  
Nerve Fibers ◽  
Nerve Membrane ◽  
Appreciable Change ◽  
A Value ◽  
Apparent Activation Energies ◽  
And Diffusion

Osmotic and diffusion permeabilities (Pf and Pd) of invertebrate nerve fibers to tritiated water were measured to determine what water flux studies could reveal about "the nerve membrane" and to directly test the possibility of active transport of water into or out of invertebrate nerve fibers. Pf/Pd ratios for lobster walking leg nerve fibers were found to be about 20 ± 7 at 14°C. Pd measurements were made for squid giant axons at 25°C. and found to yield a value of 4 x 10–4 cm.–1 sec.–1. When combined with the data of D. K. Hill for Pf, a Pf/Pd ratio of 21 ± 5 is obtained. These Pf/Pd ratios correspond to "effective pore radii" of about 16 ± 4 angstrom units, according to theories developed by Koefoed-Johnsen and Ussing and independently by Pappenheimer and his colleagues. Variations of water flux ratios with temperatures were studied and apparent activation energies calculated for both diffusion experiments and osmotic filtration experiments using the Arrhenius equation, and found to be close to 3 to 5 cal. per mole of water transferred. Cyanide (5 x 10–3 molar) and iodoacetate (1 x 10–3 molar) poisoned lobster leg nerve fibers showed no appreciable change in diffusion or osmotic filtration water effluxes. Caution in interpreting these proposed channels as simple pores was emphasized, but the possibility that such channels exist and are related to ionic flow is not incompatible with electrophysiological data.

scholarly journals Nonlinear Scaling of Surface Water Diffusion with Bulk Water Viscosity of Crowded Solutions

2013 ◽  
Vol 135 (11) ◽  
pp. 4175-4178 ◽  
Author(s):  
John M. Franck ◽  
John A. Scott ◽  
Songi Han
Keyword(s):  
Surface Water ◽  
Bulk Water ◽  
Water Diffusion ◽  
Water Viscosity

scholarly journals High-Throughput Microfiltration Membranes with Natural Biofouling Reducer Agent for Food Processing

Processes ◽  
2018 ◽  
Vol 7 (1) ◽  
pp. 1 ◽  
Author(s):  
Panggulu Utoro ◽  
Agung Sukoyo ◽  
Sandra Sandra ◽  
Nimatul Izza ◽  
Shinta Dewi ◽  
...  
Keyword(s):  
Cellulose Acetate ◽  
High Throughput ◽  
Water Flux ◽  
Antibacterial Properties ◽  
Mixed Matrix Membranes ◽  
Bacterial Cells ◽  
E Coli ◽  
Membrane Surfaces ◽  
Cellulose Acetate Membranes ◽  
Microfiltration Membranes

The effect of natural antibiotics Moringa oleifera seeds powder in cellulose acetate membranes as biofouling reducer agent was investigated. Mixed matrix membranes (MMM) were synthesized by adding 100 mesh M. oleifera seeds powder with variation of three concentrations (1 wt%, 2 wt%, and 3 wt%), into a mix polymer solution of CA (cellulose acetate) and two different solvents, i.e., DMF (dimethylformamide) and DMAc (dimethylacetamide). The synthesized membranes morphology was observed under scanning electron microscopy and from the images can be seen that the membranes made of DMAc formed rather large macrovoid as compared to DMF-based membranes. The microstructure affected the water flux through the membranes, in which the DMAc membranes provided a higher flux value and served as high-throughput microfiltration membranes. Antibacterial properties of MMM were tested using Escherichia coli adhesion onto membrane surfaces. The results showed that M. oleifera has been proven to eradicate E. coli activity on the membrane surfaces due to interaction between bacterial cells and phenolic compounds from M. oleifera, through absorption processes involving hydrogen bonds.

scholarly journals Effect of biosurfactant as a novel draw solution on photocatalytic treatment and desalination of produced water by different forward osmosis membranes

2019 ◽  
Vol 20 (1) ◽  
pp. 240-250 ◽  
Author(s):  
Maryam Taghizadeh ◽  
Daryoush Yousefi Kebria ◽  
Farhad Qaderi
Keyword(s):  
Produced Water ◽  
Membrane Surface ◽  
Water Flux ◽  
Forward Osmosis ◽  
Cellulose Triacetate ◽  
Salt Flux ◽  
Draw Solution ◽  
Benzene Toluene ◽  
Reverse Salt Flux ◽  
Contact Angle Analysis

Abstract Water stress and environmental concerns have driven research into the treatment of produced water. In this study, a combination of forward osmosis and photocatalyst system was used for simultaneous salt removal and treatment of produced water. Furthermore, biosurfactant as a novel draw solution and the three types of forward osmosis membranes (cellulose triacetate with and without titanium dioxide (TiO2) and graphene oxide (GO) nanoparticles) were investigated. The morphology and distribution of the TiO2 and TiO2/GO on the membrane surface were assessed by various analyses including field emission scanning electron microscopy, energy dispersive X-ray and contact angle analysis. The results demonstrated that the reverse salt flux was only 0.2 g/m2 h. Moreover, benzene, toluene, ethylbenzene, and xylene (BTEX) removal efficiency in the cellulose triacetate with TiO2 and TiO2/GO membrane under UVC radiation was 62% and 78%, respectively, while the data obtained in visible light reached 80%. The use of TiO2 and TiO2/GO membranes significantly improved the permeability, water flux, photocatalytic degradation of pollutants and desalination of produced water.

Sign in / Sign up

Export Citation Format

Share Document