scholarly journals Local flow assessment of the Japan Bulk Carrier using different turbulence models

2021 ◽  
Vol 1182 (1) ◽  
pp. 012004
Author(s):  
A Bekhit ◽  
F Popescu
Keyword(s):  
Experimental Data ◽  
Viscous Flow ◽  
Turbulence Models ◽  
Wake Flow ◽  
Design Stage ◽  
Bulk Carrier ◽  
Local Flow ◽  
Special Investigation ◽  
Ship Wake ◽  
Effective Wake

Abstract Ship resistance and powering represent the most important aspects in the initial design stage of the ship. Based on their estimation the basic milestone for selecting the main engine and the propulsion system is established. The majority of ships in the international fleet nowadays rely on the screw propeller working in the wake zone behind the ship. The wake flow of the ship has a direct impact on the propeller performance and the propulsion efficiency. Accurate prediction of the nominal and effective wake is crucially important to provide a proper understanding of the flow where the propeller will perform. From this point of view, the wake flow of the Capesize Japan Bulk Carrier (JBC) is assessed using a viscous flow Computational Fluid Dynamics (CFD) method. Numerical simulations are performed to predict the nominal and effective wake of the ship by making use of the viscous flow solver ISIS_CFD of the FINETM/Marine software provided by NUMECA. The solver is based on the finite volume method to build the spatial discretization of the transport equation to resolve the Reynolds-Averaged Navier-Stokes (RANS) equations. Closure to turbulence is achieved using different turbulence models in order to investigate their accuracy in predicting the complex wake flow of the ship. Two-phase flow approach is used to model the air-water interface where the Volume of Fluid method is implemented to capture the free-surface. The results for both nominal and effective wake are assessed against the experimental data provided by the National Maritime Research Institute (NMRI) and Yokohama National University in Japan that were presented in the seventh Workshop on CFD in ship hydrodynamics (Tokyo2015). The results validation showed a reasonable agreement compared to the experimental data for both nominal and effective wake. As it was expected, some turbulence models showed to be more accurate in predicting ship wake, especially the Shear Stress Transport (K-ω SST) and Explicit Algebraic Reynolds Stress (EASM) Models. A special investigation of the flow vortices is also taken into consideration.

Numerical analysis for wake flow field of Ahmed model based on a nonlinear-LRN/DES turbulence model

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Le Dian Zheng ◽  
Yi Yang ◽  
Guang Lin Qiang ◽  
Zhengqi Gu
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Reynolds Stress ◽  
Turbulence Model ◽  
Turbulence Models ◽  
Aerodynamic Characteristics ◽  
Wake Flow ◽  
Field Analysis ◽  
Content Type ◽  
Des Model

Purpose This paper aims to propose a precise turbulence model for automobile aerodynamics simulation, which can predict flow separation and reattachment phenomena more accurately. Design/methodology/approach As the results of wake flow simulation with commonly used turbulence models are unsatisfactory, by introducing a nonlinear Reynolds stress term and combining the detached Eddy simulation (DES) model, this paper proposes a nonlinear-low-Reynolds number (LRN)/DES turbulence model. The turbulence model is verified in a backward-facing step case and applied in the flow field analysis of the Ahmed model. Several widely applied turbulence models are compared with the nonlinear-LRN/DES model and the experimental data of the above cases. Findings Compared with the experimental data and several turbulence models, the nonlinear-LRN/DES model gives better agreement with the experiment and can predict the automobile wake flow structures and aerodynamic characteristics more accurately. Research limitations/implications The nonlinear-LRN/DES model proposed in this paper suffers from separation delays when simulating the separation flows above the rear slant of the Ahmed body. Therefore, more factors need to be considered to further improve the accuracy of the model. Practical implications This paper proposes a turbulence model that can more accurately simulate the wake flow field structure of automobiles, which is valuable for improving the calculation accuracy of the aerodynamic characteristics of automobiles. Originality/value Based on the nonlinear eddy viscosity method and the scale resolved simulation, a nonlinear-LRN/DES turbulence model including the nonlinear Reynolds stress terms for separation and reattachment prediction, as well as the wake vortex structure prediction is first proposed.

Viscous Flow Field Computations for the VKI–1 Turbine Cascade Using Different Turbulence Models

1995 ◽  
Author(s):  
L. J. Lenke ◽  
A. W. Reichert ◽  
H. Simon
Keyword(s):  
Flow Field ◽  
Viscous Flow ◽  
Measurement Data ◽  
Turbulence Models ◽  
Algebraic Model ◽  
Turbulence Modelling ◽  
Wake Flow ◽  
Field Calculation ◽  
Wall Functions ◽  
Viscous Flow Field

The influence of the turbulence modelling on viscous flow field calculation results has often been discussed in the past. For a meaningful comparison of different turbulence models the access to reliable measurement data is necessary. The plane VKI–1 turbine profile has been investigated experimentally in many publications. Therefore this turbine profile is chosen for transonic 2D flow field calculations using three different turbulence models. The algebraic model of Baldwin and Lomax, the Standard k–ϵ model with wall functions and a low–Reynolds number model are considered in this investigation. The main differences between the models become apparent in the trailing edge region. The turbulence modelling influences the boundary layer thickness and the shape of the shear layers and the separation region in the wake flow. For the high Mach numbers appearing in this region, a strong influence on the flow field due to small shear layer changes has been found.

Viscous Flow Computations on a Smooth Cylinders: A Detailed Numerical Study With Validation

2007 ◽  
Author(s):  
Guilherme Vaz ◽  
Christophe Mabilat ◽  
Remmelt van der Wal ◽  
Paul Gallagher
Keyword(s):  
Experimental Data ◽  
Viscous Flow ◽  
Numerical Study ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Time Step ◽  
Drag Forces

The objective of this paper is to investigate several numerical and modelling features that the CFD community is currently using to compute the flow around a fixed smooth circular cylinder. Two high Reynolds numbers, 9 × 104 and 5 × 105, are chosen which are in the so called drag-crisis region. Using a viscous flow solver, these features are assessed in terms of quality by comparing the numerical results with experimental data. The study involves grid sensitivity, time step sensitivity, the use of different turbulence models, three-dimensional effects, and a RANS/DES (Reynolds Averaged Navier Stokes, Detached Eddy Simulation) comparison. The resulting drag forces and Strouhal numbers are compared with experimental data of different sources. Major flow features such as velocity and vorticity fields are presented. One of the main conclusions of the present study is that all models predict forces which are far from the experimental values, particularly for the higher Reynolds numbers in the drag-crisis region. Three-dimensional and unsteadiness effects are present, but are only fully captured by sophisticated turbulence models or by DES. DES seems to be the key to better solve the flow problem and obtain better agreement with experimental data. However, its considerable computational demands still do not allow to use it for engineering design purposes.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

Simulation of the Gap Resonance Between Two Rectangular Barges in Regular Waves by a Free Surface Viscous Flow Solver

2013 ◽  
Author(s):  
B. Elie ◽  
G. Reliquet ◽  
P.-E. Guillerm ◽  
O. Thilleul ◽  
P. Ferrant ◽  
...  
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Viscous Flow ◽  
Stokes Equations ◽  
Resonance Phenomenon ◽  
Navier Stokes ◽  
Regular Waves ◽  
Navier Stokes Equations ◽  
Flow Solver ◽  
Gap Resonance

This paper compares numerical and experimental results in the study of the resonance phenomenon which appears between two side-by-side fixed barges for different sea-states. Simulations were performed using SWENSE (Spectral Wave Explicit Navier-Stokes Equations) approach and results are compared with experimental data on two fixed barges with different headings and bilges. Numerical results, obtained using the SWENSE approach, are able to predict both the frequency and the magnitude of the RAO functions.

scholarly journals Performance of Turbulence Models and Near-Wall Treatments in Discrete Jet Film Cooling Simulations

1998 ◽  
Author(s):  
Jeffrey D. Ferguson ◽  
Dibbon K. Walters ◽  
James H. Leylek
Keyword(s):  
Experimental Data ◽  
Film Cooling ◽  
Turbulence Models ◽  
Viscous Sublayer ◽  
Reynolds Stress Model ◽  
Quality Data ◽  
Wall Functions ◽  
First Time ◽  
Near Wall ◽  
Non Equilibrium

For the first time in the open literature, code validation quality data and a well-tested, highly reliable computational methodology are employed to isolate the true performance of seven turbulence treatments in discrete jet film cooling. The present research examines both computational and high quality experimental data for two length-to-diameter ratios of a row of streamwise injected, cylindrical film holes. These two cases are used to document the performance of the following turbulence treatments: 1) standard k-ε model with generalized wall functions; 2) standard k-ε model with non-equilibrium wall functions: 3) Renormalization Group k-ε (RNG) model with generalized wall functions; 4) RNG model with non-equilibrium wall functions: 51 standard k-ε model with two-layer turbulence wall treatment; 6) Reynolds Stress Model (RSM) with generalized wall functions; and 7) RSM with non-equilibrium wall functions. Overall, the standard k-ε turbulence model with the two-layer near-wall treatment, which resolves the viscous sublayer, produces results that are more consistent with experimental data.

A Hybrid Viscous/Potential Flow Method for the Prediction of the Performance of Podded and Ducted Propellers

2009 ◽  
Author(s):  
Spyros A. Kinnas ◽  
Shu-Hao Chang ◽  
Yi-Hsiang Yu ◽  
Lei He
Keyword(s):  
Viscous Flow ◽  
Lattice Method ◽  
Viscous Potential Flow ◽  
Flow Solver ◽  
Vortex Lattice Method ◽  
Ducted Propeller ◽  
Hybrid Numerical Method ◽  
Convergence Study ◽  
Effective Wake ◽  
Ducted Propellers

This paper presents the analysis of the performance for podded and ducted propellers using a hybrid numerical method, which couples a vortex lattice method (MPUF-3A) for the unsteady analysis of propellers and a viscous flow solver (NS-3X or FLUENT) for the prediction of the viscous flow around propulsors and the drag force on the pod and duct surfaces. The time averaged propeller force distributions are considered as source terms (body force) in the momentum equations of NS-3X and FLUENT. The effects of viscosity on the effective wake and on the performance of the propeller blade, as well as on the predicted pod and duct forces, are assessed. The convergence study of circulation distributions with number of lattices is reported in the ducted propeller case. Finally, the prediction of the performance for podded propellers (both single pull-type and twin-type) and ducted propellers from the present method is validated against existing experimental data.

Calculation of Flow in Mixing Vessels With Various Turbulence Models

Volume 4 ◽  
2004 ◽  
Author(s):  
Branislav Basara ◽  
Ales Alajbegovic ◽  
Decan Beader
Keyword(s):  
Experimental Data ◽  
Mathematical Model ◽  
Finite Volume Method ◽  
Finite Volume ◽  
Turbulence Model ◽  
Unstructured Grids ◽  
Turbulence Models ◽  
Cfd Applications ◽  
Volume Method ◽  
Rushton Impeller

The paper presents calculations of flow in a mixing vessel stirred by a six-blade Rushton impeller. Mathematical model used in computations is based on the ensemble averaged conservation equations. An efficient finite-volume method based on unstructured grids with rotating sliding parts composed of arbitrary polyhedral elements is used together with various turbulence models. Besides the standard k-ε model which served as a reference, k-ε-v2 model (Durbin, 1995) and the recently proposed hybrid EVM/RSM turbulence model (Basara & Jakirlic, 2003) were used in the calculations. The main aim of the paper is to investigate if more advanced turbulence models are needed for this type of CFD applications. The results are compared with the available experimental data.

Flow Analysis of a Hydrocyclone Designed to High Oil Content Application

2009 ◽  
Author(s):  
G. M. Raposo ◽  
A. O. Nieckele
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Oil Content ◽  
Flow Analysis ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Tangential Component ◽  
Inlet Flow ◽  
Unit Process ◽  
Inlet Flow Rate

Development of small size and weight separation equipment are crucial for the petroleum off-shore exploration. Since centrifugal fields are several times stronger than the gravity field, cyclonic separation has became very important as a unit process for compact gas-liquid, liquid-liquid and solid-liquid separation. The major difference between the various cyclones is their geometry. Cyclone optimization for different uses is, every year, less based on experiments and more based on mathematical models. In the present work, the flow field inside high oil content hydrocyclones is numerically obtained with FLUENT. The performance of two turbulence models, Reynolds Stress Model (RSM) and Large Eddy Simulation (LES), to predict the flow inside a high oil content hydrocyclone, is investigated by comparing the results with experimental data available in the literature. All models overpredicted the tangential component, especially at the reverse cone region. However, the prediction of the tangential turbulent fluctuations with LES was significant better than the RSM prediction. The influences of the inlet flow rate and hydrocyclone length in the flow were also evaluated. RSM model was able to foresee correctly, in agreement with experimental data, the correct tendency of pressure drop reduction with decreasing inlet flow rate and increasing length.

scholarly journals 2D Numerical Simulation Study of Airfoil Performance

2021 ◽  
Author(s):  
Nasser Shelil
Keyword(s):  
Experimental Data ◽  
Wind Tunnel ◽  
Air Temperature ◽  
Wind Turbines ◽  
Aerodynamic Force ◽  
Angle Of Attack ◽  
Turbulence Models ◽  
Aerodynamic Characteristics ◽  
Operating Conditions ◽  
Ansys Fluent

Abstract. The aerodynamic characteristics of DTU-LN221 airfoil is studied. ANSYS Fluent is used to simulate the airfoil performance with seven different turbulence models. The simulation results for the airfoil with different turbulence models are compared with the wind tunnel experimental data performed under the same operating conditions. It is found that there is a good agreement between the computational fluid dynamics (CFD) predicted aerodynamic force coefficients with wind tunnel experimental data especially with angle of attack between −5° to 10°. RSM is chosen to investigate the flow field structure and the surface pressure coefficients under different angle of attack between −5° to 10°. Also the effect of changing air temperature, velocity and turbulence intensity on lift and drag coefficients/forces are examined. The results show that it is recommended to operate the wind turbines airfoil at low air temperature and high velocity to enhance the performance of the wind turbines.

Sign in / Sign up

Export Citation Format

Share Document