scholarly journals Progressive failure mechanical behaviour and response characteristics of sandstone under stress-seepage coupling

2021 ◽  
Vol 18 (2) ◽  
pp. 1-19
Author(s):  
Zhixiang Song ◽  
Junwen Zhang
Keyword(s):  
Mechanical Behaviour ◽  
Pressure Effect ◽  
Axial Strain ◽  
Water Inrush ◽  
Confining Pressure ◽  
Permeability Model ◽  
Triaxial Loading ◽  
Seepage Pressure ◽  
Confining Pressures ◽  
Confining Pressure Effect

Abstract Conventional triaxial loading tests with different confining pressures and stress-seepage coupling tests on sandstone with different confining pressures and seepage pressures were conducted. A permeability model considering strength and strain was established, which better characterized the progressive deformation mechanical behaviour of sandstone under stress-seepage coupling. The results showed the following. (i) The confining pressure not only affects the peak strength of sandstone but also affects the axial deformation under conventional triaxial loading conditions. (ii) Compared with the seepage pressure effect, the degree of the confining pressure effect on the strength of sandstone was weaker, but the degree of that on the axial, radial and volumetric deformations of sandstone was stronger under stress-seepage coupling. (iii) With increasing confining pressure, the axial strain of sandstone decreased, while the corresponding radial and volumetric strains showed progressively increasing evolution characteristics under identical seepage pressures and different confining pressures. With increasing seepage pressure, the axial strain continuously decreased, while the corresponding radial and volumetric strains showed the progressive evolution characteristic of first increasing and then decreasing under identical confining pressures and different seepage pressures. (iv) Compared with the confining pressure effect, the degree of the seepage pressure effect on the permeability progressive evolution law of sandstone was weaker under stress-seepage coupling. The research conclusions could enrich the theories for the prevention and control of water inrush accidents in coal mines.

scholarly journals Experimental Research into the Evolution of Permeability of Sandstone under Triaxial Compression

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5065
Author(s):  
Liming Zhang ◽  
Shengqun Jiang ◽  
Jin Yu
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Testing Machine ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Rate Of Change ◽  
Peak Strength ◽  
Sudden Increase ◽  
Seepage Pressure ◽  
Confining Pressures

Failure tests on sandstone specimens were conducted under different confining pressures and seepage pressures by using an MTS triaxial rock testing machine to elucidate the corresponding correlations of permeability and characteristic stress with confining pressure and pore pressure during deformation. The results indicate that permeability first decreases and presents two trends, i.e., a V-shaped increase and an S-shaped trend during the non-linear deformation stage. The greater the seepage pressure, the greater the initial permeability and the more obvious the V-shaped trend in the permeability. As the confining pressure was increased, the trend in the permeability gradually changed from V- to S-shaped. Compared with the case at a high confining pressure, the decrease of permeability occurred more quickly, the rate of change becomes greater, and the sudden increase observed in the permeability happened earlier under lower confining pressures. Within the range tested, confining pressure exerted a greater effect on the permeability than the seepage pressure. In comparison with the axial strain, volumetric strain better reflected changes in permeability during compaction and dilation of sandstone. The ratio of crack initiation stress to peak strength ranged from 0.37 to 0.50, while the ratio of dilation stress to peak strength changed from 0.58 to 0.72. Permeabilities calculated based on Darcy and non-Darcy flow changed within the same interval, while the change in permeability was different.

scholarly journals Constitutive Model of N15 Propellant considering the Confining Pressure Effect

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Tianpeng Li ◽  
Junli Han ◽  
Shixin Wang ◽  
Yong He ◽  
Xiong Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Pressure Effect ◽  
Rupture Strength ◽  
Confining Pressure ◽  
Test System ◽  
Model Parameters ◽  
Initial Modulus ◽  
Confining Pressures ◽  
Confining Pressure Effect

To describe the effect of confining pressure on the mechanical responses of N15 propellant, a constitutive model considering the confining pressure effect was first established for N15 propellant based on the elastic-viscoelastic correspondence principle. Then, the mechanical properties of N15 solid propellant under different confining pressures were obtained using confining pressure test system, and the obtained results indicate that the initial modulus of propellant did not change with confining pressure, but the maximum tensile strength, rupture strength, the maximum elongation, and elongation at break increased with increasing confining pressure. In conjunction with propellants’ mesoscopic structure and cross-section analysis, the mechanical mechanism of confining pressure effect on propellant was initially disclosed. Due to confining pressure, the particle dewetting inside the propellant was reduced, the hole propagation was delayed, and crack extension inhibited germination, proving that confining pressure has a strengthening impact on the propellant. Finally, assuming that the model parameters were dependent on pressure, the model parameters acquisition and validation were conducted. The results demonstrated that constitutive model can describe confining pressure influence on the mechanical properties of N15 propellant accurately.

Study on Compression Resistance under Different Confining Pressures and Parameters of Cam-Clay Model of Bentonite

2014 ◽  
Vol 501-504 ◽  
pp. 430-433
Author(s):  
Jun Jie Hou ◽  
Lan Qiao ◽  
Qing Chi Cai ◽  
Zhen Li
Keyword(s):  
Compressive Strength ◽  
Pressure Effect ◽  
Confining Pressure ◽  
Experimental Results ◽  
Consolidation Test ◽  
Clay Model ◽  
Confining Pressures ◽  
Confining Pressure Effect ◽  
Compression Resistance ◽  
Cam Clay

Factors such as density and confining pressure effect on the compressive strength were analyzed by comparing the experimental results under different conditions, the parameters of Cambridge model were worked out with the data from consolidation test.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

scholarly journals The Effect of Confining Pressure on the Mechanical Properties of Sand–Ice Materials

1973 ◽  
Vol 12 (66) ◽  
pp. 469-481 ◽  
Author(s):  
Bernard D. Alkire ◽  
Orlando B. Andersland
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Silica Sand ◽  
Creep Tests ◽  
Ice Volume ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Sand Material ◽  
Cylindrical Samples

Cylindrical samples containing 0.59 mm to 0.84 mm diameter silica sand at about 97% and 55% ice saturation (the ratio of ice volume to sand pore volume) were tested at a temperature of −12° C in triaxial compression. Both constant axial strain-rate tests and step-stress creep tests provide information on the influence of confining pressure on the shear strength and creep behavior of the sand–ice material. Changes in the degree of ice saturation help show the influence of the ice matrix versus the sand material on the mechanical behavior. Data are discussed in terms of the Mohr–Coulomb failure law and creep theories. It is shown that the cohesive component of strength depends on response of the ice matrix, whereas the frictional component of strength responds in a manner very similar to unfrozen sand tested at high confining pressures. Experimental data show that creep rates decrease exponentially and creep strength increases with an increase in confining pressure.

scholarly journals Research on the Development Mechanism of Postpeak Cracks in Sandstone under Different Confining Pressures

2019 ◽  
Vol 2019 ◽  
pp. 1-10
Author(s):  
Jihua Zhang ◽  
Lianguo Wang ◽  
Yun Dong ◽  
Yadong Chen ◽  
Yang Jiang ◽  
...  
Keyword(s):  
Probability Density ◽  
Water Inrush ◽  
Confining Pressure ◽  
Ct Images ◽  
Surrounding Rock ◽  
Internal Crack ◽  
Geometrical Parameters ◽  
Stress Levels ◽  
Confining Pressures ◽  
Development Mechanism

Water inrush happens occasionally during deeper roadways excavation. It is mainly due to the lack of understanding in the formation and development mechanism of cracks and its spatial distribution pattern under ground stress. In view of this, this paper used different stress levels to represent the fracture state of different parts of the surrounding rock of the deep roadway; CT detection technique is used to scan the fractured sandstone in the postpeak state; and the CT images under different confining pressures are thus obtained. The geometrical parameters such as area, length, and width of the crack are used to describe the distribution patterns based on CT images processing technique and statistical principle. These patterns are then analyzed under varying postpeak stress levels and confining pressures. The result shows that, as the area, length, and width of the cracks get larger, number of cracks increases with decreasing stress level; at different stress levels, sandstone crack area probability density, crack length probability density, and crack width probability density form exceptional, linear, and Gaussian distribution, respectively. The amount of confining pressure affects the size of cracks and the extent of expansion. This means that the higher the confining pressure is, the easier the internal crack will be penetrated and expanded and the bigger the cracks are, and the number of cracks gets lesser. Such research results can be used to describe the propagation and evolution law of cracks under different stress states of postpeak rock, which also provide an important basis for further analysis of its permeability and the stability of roadway surrounding rock.

scholarly journals Effect of Geotextile Reinforcement on Shear Strength of Sandy Soil: Laboratory Study

2016 ◽  
Vol 38 (4) ◽  
pp. 3-13 ◽  
Author(s):  
Sidali Denine ◽  
Noureddine Della ◽  
Muhammed Rawaz Dlawar ◽  
Feia Sadok ◽  
Jean Canou ◽  
...  
Keyword(s):  
Shear Strength ◽  
Mechanical Behaviour ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Loose Sand ◽  
Test Results ◽  
Compression Tests ◽  
Confining Stress ◽  
Natural Sand ◽  
Confining Pressures

Abstract This paper presents results of a series of undrained monotonic compression tests on loose sand reinforced with geotextile mainly to study the effect of confining stress on the mechanical behaviour of geotextile reinforced sand. The triaxial tests were performed on reconstituted specimens of dry natural sand prepared at loose relative density (Dr = 30%) with and without geotextile layers and consolidated to three levels of confining pressures 50, 100 and 200 kPa, where different numbers and different arrangements of reinforcement layers were placed at different heights of the specimens (0, 1 and 2 layers). The behaviour of test specimens was presented and discussed. Test results showed that geotextile inclusion improves the mechanical behaviour of sand, a significant increase in the shear strength and cohesion value is obtained by adding up layers of reinforcement. Also, the results indicate that the strength ratio is more pronounced for samples which were subjected to low value of confining pressure. The obtained results reveal that high value of confining pressure can restrict the sand shear dilatancy and the more effect of reinforcement efficiently.

Sign in / Sign up

Export Citation Format

Share Document