scholarly journals Automatic projection image registration for nanoscale X-ray tomographic reconstruction

2018 ◽  
Vol 25 (6) ◽  
pp. 1819-1826 ◽  
Author(s):  
Haiyan Yu ◽  
Sihao Xia ◽  
Chenxi Wei ◽  
Yuwei Mao ◽  
Daniel Larsson ◽  
...  
Keyword(s):  
Spatial Resolution ◽  
Imaging Modality ◽  
Energy State ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
Visual Assessment ◽  
Superior Performance ◽  
X Rays ◽  
X Ray ◽  
Projection Images

Novel developments in X-ray sources, optics and detectors have significantly advanced the capability of X-ray microscopy at the nanoscale. Depending on the imaging modality and the photon energy, state-of-the-art X-ray microscopes are routinely operated at a spatial resolution of tens of nanometres for hard X-rays or ∼10 nm for soft X-rays. The improvement in spatial resolution, however, has led to challenges in the tomographic reconstruction due to the fact that the imperfections of the mechanical system become clearly detectable in the projection images. Without proper registration of the projection images, a severe point spread function will be introduced into the tomographic reconstructions, causing the reduction of the three-dimensional (3D) spatial resolution as well as the enhancement of image artifacts. Here the development of a method that iteratively performs registration of the experimentally measured projection images to those that are numerically calculated by reprojecting the 3D matrix in the corresponding viewing angles is shown. Multiple algorithms are implemented to conduct the registration, which corrects the translational and/or the rotational errors. A sequence that offers a superior performance is presented and discussed. Going beyond the visual assessment of the reconstruction results, the morphological quantification of a battery electrode particle that has gone through substantial cycling is investigated. The results show that the presented method has led to a better quality tomographic reconstruction, which, subsequently, promotes the fidelity in the quantification of the sample morphology.

High spatial resolution x-ray microanalysis of interfaces

1995 ◽  
Vol 53 ◽  
pp. 284-285
Author(s):  
J. R. Michael
Keyword(s):  
Spatial Resolution ◽  
Electron Probe ◽  
Solid Angle ◽  
Collection Efficiency ◽  
Spatial Scales ◽  
Energy Dispersive Spectrometer ◽  
X Rays ◽  
X Ray ◽  
Probe Size ◽  
Brightness Field

X-ray microanalysis in the analytical electron microscope (AEM) refers to a technique by which chemical composition can be determined on spatial scales of less than 10 nm. There are many factors that influence the quality of x-ray microanalysis. The minimum probe size with sufficient current for microanalysis that can be generated determines the ultimate spatial resolution of each individual microanalysis. However, it is also necessary to collect efficiently the x-rays generated. Modern high brightness field emission gun equipped AEMs can now generate probes that are less than 1 nm in diameter with high probe currents. Improving the x-ray collection solid angle of the solid state energy dispersive spectrometer (EDS) results in more efficient collection of x-ray generated by the interaction of the electron probe with the specimen, thus reducing the minimum detectability limit. The combination of decreased interaction volume due to smaller electron probe size and the increased collection efficiency due to larger solid angle of x-ray collection should enhance our ability to study interfacial segregation.

scholarly journals Is Micro X-ray Computer Tomography a Suitable Non-Destructive Method for the Characterisation of Dental Materials?

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1271
Author(s):  
Andreas Koenig ◽  
Leonie Schmohl ◽  
Johannes Scheffler ◽  
Florian Fuchs ◽  
Michaela Schulz-Siegmund ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Computer Tomography ◽  
Mechanical Performance ◽  
Dental Materials ◽  
Three Dimensional ◽  
X Rays ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Multiple Measurements ◽  
High Doses

The aim of the study was to investigate the effect of X-rays used in micro X-ray computer tomography (µXCT) on the mechanical performance and microstructure of a variety of dental materials. Standardised bending beams (2 × 2 × 25 mm3) were forwarded to irradiation with an industrial tomograph. Using three-dimensional datasets, the porosity of the materials was quantified and flexural strength was investigated prior to and after irradiation. The thermal properties of irradiated and unirradiated materials were analysed and compared by means of differential scanning calorimetry (DSC). Single µXCT measurements led to a significant decrease in flexural strength of polycarbonate with acrylnitril-butadien-styrol (PC-ABS). No significant influence in flexural strength was identified for resin-based composites (RBCs), poly(methyl methacrylate) (PMMA), and zinc phosphate cement (HAR) after a single irradiation by measurement. However, DSC results suggest that changes in the microstructure of PMMA are possible with increasing radiation doses (multiple measurements, longer measurements, higher output power from the X-ray tube). In summary, it must be assumed that X-ray radiation during µXCT measurement at high doses can lead to changes in the structure and properties of certain polymers.

Visualizing Fluid Flows With X-Rays

2007 ◽  
Author(s):  
Theodore J. Heindel ◽  
Terrence C. Jensen ◽  
Joseph N. Gray
Keyword(s):  
Computed Tomography ◽  
Flow Visualization ◽  
Three Dimensional ◽  
Fluid Flows ◽  
X Rays ◽  
Radiographic Images ◽  
Optical Access ◽  
X Ray ◽  
X Ray Computed ◽  
Density Map

There are several methods available to visualize fluid flows when one has optical access. However, when optical access is limited to near the boundaries or not available at all, alternative visualization methods are required. This paper will describe flow visualization using an X-ray system that is capable of digital X-ray radiography, digital X-ray stereography, and digital X-ray computed tomography (CT). The unique X-ray flow visualization facility will be briefly described, and then flow visualization of various systems will be shown. Radiographs provide a two-dimensional density map of a three dimensional process or object. Radiographic images of various multiphase flows will be presented. When two X-ray sources and detectors simultaneously acquire images of the same process or object from different orientations, stereographic imaging can be completed; this type of imaging will be demonstrated by trickling water through packed columns and by absorbing water in a porous medium. Finally, local time-averaged phase distributions can be determined from X-ray computed tomography (CT) imaging, and this will be shown by comparing CT images from two different gas-liquid sparged columns.

Recent Developments In Monochromatic Microprobe X-Ray Fluorescence (MMXRF)

1998 ◽  
Vol 4 (S2) ◽  
pp. 378-379
Author(s):  
Z. W. Chen ◽  
D. B. Wittry
Keyword(s):  
Materials Science ◽  
High Vacuum ◽  
Three Dimensional ◽  
High Sensitivity ◽  
X Rays ◽  
Fluorescence Excitation ◽  
X Ray ◽  
Quantitative Microanalysis ◽  
Recent Developments ◽  
Fifth Order

A monochromatic x-ray microprobe based on a laboratory source has recently been developed in our laboratory and used for fluorescence excitation. This technique provides high sensitivity (ppm to ppb), nondestructive, quantitative microanalysis with minimum sample preparation and does not require a high vacuum specimen chamber. It is expected that this technique (MMXRF) will have important applications in materials science, geological sciences and biological science.Three-dimensional focusing of x-rays can be obtained by using diffraction from doubly curved crystals. In our MMXRF setup, a small x-ray source was produced by the bombardment of a selected target with a focused electron beam and a toroidal mica diffractor with Johann pointfocusing geometry was used to focus characteristic x-rays from the source. In the previous work ∼ 108 photons/s were obtained in a Cu Kα probe of 75 μm × 43 μm in the specimen plane using the fifth order reflection of the (002) planes of mica.

X-ray Microscopy in your Lab

2013 ◽  
Vol 21 (2) ◽  
pp. 7-7
Author(s):  
Charles Lyman
Keyword(s):  
Grain Size ◽  
Point Source ◽  
Visible Light ◽  
Light Microscope ◽  
Construction Materials ◽  
X Rays ◽  
X Ray ◽  
Projection Images ◽  
Straight Lines

Using X rays to produce magnified images of objects has been a goal for 150 years. Ever since Ernst Abbe declared in 1873 that light microscope resolution was limited by the wavelength of light, the search was on for a microscopy medium with a wavelength shorter than visible light (<500 nm). When Roentgen discovered X rays in 1895, it was thought that the new medium may have been found. Soon it was clear, however, that it was not easy to construct a physical lens for X rays because the rays penetrated all lens construction materials. X-ray “radiography images” of a few times magnification were possible but only as projection images, formed as X rays from millimeter-sized sources traveled in straight lines through the specimen to be captured on film. Unfortunately, even in the best cases, useful magnification was limited by the relatively large “point source” of X rays and the large grain size of X-ray film (both about 0.1–1.0 mm).

scholarly journals Hard X-ray polarizer to enable simultaneous three-dimensional nanoscale imaging of magnetic structure and lattice strain

2016 ◽  
Vol 23 (5) ◽  
pp. 1210-1215 ◽  
Author(s):  
Jonathan Logan ◽  
Ross Harder ◽  
Luxi Li ◽  
Daniel Haskel ◽  
Pice Chen ◽  
...  
Keyword(s):  
Magnetic Circular Dichroism ◽  
Three Dimensional ◽  
Control Sample ◽  
Magnetic Ordering ◽  
X Rays ◽  
Diffractive Imaging ◽  
X Ray ◽  
Coherent Diffractive Imaging ◽  
Diffraction Patterns ◽  
A New Technique

Recent progress in the development of dichroic Bragg coherent diffractive imaging, a new technique for simultaneous three-dimensional imaging of strain and magnetization at the nanoscale, is reported. This progress includes the installation of a diamond X-ray phase retarder at beamline 34-ID-C of the Advanced Photon Source. The performance of the phase retarder for tuning X-ray polarization is demonstrated with temperature-dependent X-ray magnetic circular dichroism measurements on a gadolinium foil in transmission and on a Gd5Si2Ge2crystal in diffraction geometry with a partially coherent, focused X-ray beam. Feasibility tests for dichroic Bragg coherent diffractive imaging are presented. These tests include (1) using conventional Bragg coherent diffractive imaging to determine whether the phase retarder introduces aberrations using a nonmagnetic gold nanocrystal as a control sample, and (2) collecting coherent diffraction patterns of a magnetic Gd5Si2Ge2nanocrystal with left- and right-circularly polarized X-rays. Future applications of dichroic Bragg coherent diffractive imaging for the correlation of strain and lattice defects with magnetic ordering and inhomogeneities are considered.

scholarly journals Synchrotron radiation X-ray tomographic microscopy (SRXTM) of brachiopod shell interiors for taxonomy: Preliminary report

2010 ◽  
pp. 109-117 ◽  
Author(s):  
Neda Motchurova-Dekova ◽  
David Harper
Keyword(s):  
Synchrotron Radiation ◽  
Three Dimensional ◽  
X Rays ◽  
X Ray ◽  
Fine Grained ◽  
Internal Structures ◽  
Efficient Alternative ◽  
Micro Tomography ◽  
Light Beams ◽  
Non Destructive

Synchrotron radiation X-ray tomographic microscopy (SRXTM) is a non-destructive technique for the investigation and visualization of the internal features of solid opaque objects, which allows reconstruction of a complete three-dimensional image of internal structures by recording of the differences in the effects on the passage of waves of energy reacting with those structures. Contrary to X-rays, produced in a conventional X-ray tube, the intense synchrotron light beams are sharply focused like a laser beam. We report encouraging results from the use of SRXTM for purely taxonomic purposes in brachiopods: an attempt to find a non-destructive and more efficient alternative to serial sectioning and several other methods of dissection together with the non-destructive method of X-ray computerised micro-tomography. Two brachiopod samples were investigated using SRXTM. In ?Rhynchonella? flustracea it was possible to visualise the 3D shape of the crura and dental plates. In Terebratulina imbricata it was possible to reveal the form of the brachidium. It is encouraging that we have obtained such promising results using SRXTM with our very first two fortuitous samples, which had respectively fine-grained limestone and marl as infilling sediment, in contrast to the discouraging results communicated to us by some colleagues who have tested specimens with such infillings using X-ray micro-tomography. In future the holotypes, rare museum specimens or delicate Recent material may be preferentially subjected to this mode of analysis.

scholarly journals Three-dimensional imaging of hold baggage for airport security

2014 ◽  
Vol XL-5 ◽  
pp. 331-336
Author(s):  
S. Kolokytha ◽  
R. Speller ◽  
S. Robson
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
Handling Time ◽  
Cost Effective ◽  
Airport Security ◽  
X Ray ◽  
Common System ◽  
Close Range

This study describes a cost-effective check-in baggage screening system, based on "on-belt tomosynthesis" (ObT) and close-range photogrammetry, that is designed to address the limitations of the most common system used, conventional projection radiography. The latter's limitations can lead to loss of information and an increase in baggage handling time, as baggage is manually searched or screened with more advanced systems. This project proposes a system that overcomes such limitations creating a cost-effective automated pseudo-3D imaging system, by combining x-ray and optical imaging to form digital tomograms. Tomographic reconstruction requires a knowledge of the change in geometry between multiple x-ray views of a common object. This is uniquely achieved using a close range photogrammetric system based on a small network of web-cameras. This paper presents the recent developments of the ObT system and describes recent findings of the photogrammetric system implementation. Based on these positive results, future work on the advancement of the ObT system as a cost-effective pseudo-3D imaging of hold baggage for airport security is proposed.

Sign in / Sign up

Export Citation Format

Share Document