Structure of lithium tellurite and vanadium lithium tellurite glasses by high-energy X-ray and neutron diffraction

2021 ◽  
Vol 77 (2) ◽  
Author(s):  
Hirdesh ◽  
Atul Khanna ◽  
Margit Fábián ◽  
Ann-Christin Dippel ◽  
Olof Gotowski
Keyword(s):  
Neutron Diffraction ◽  
Glass Network ◽  
High Energy ◽  
Coordination Shell ◽  
Tellurite Glasses ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Structure Factors ◽  
Wide Range

xLi2O–(100 − x)TeO2 (x = 20 and 25 mol%) and xV2O5–(25 − x)Li2O–75TeO2 (x = 1, 2, 3, 4 and 5 mol%) glasses were prepared by melt-quenching and their thermal and structural properties were characterized by differential scanning calorimetry, Raman spectroscopy, high-energy X-ray diffraction and neutron diffraction and reverse Monte Carlo (RMC) simulations. The glass transition temperature increases steadily with an increase in V2O5 mol% in lithium tellurite glasses due to an increase in the average single bond energy of the glass network. The X-ray and neutron diffraction structure factors were modelled by RMC technique and the Te–O distributions show the first peak in the range 1.85–1.90 Å, with V–O = 1.75–1.95 Å, Li–O = 1.85–2.15 Å and O–O = 2.70–2.80 Å. The average Te–O coordination number decreases with an increase in Li2O mol% in lithium tellurite glasses, and the V—O coordination decreases from 5.12 to 3.81 with an increase in V2O5 concentration in vanadium lithium tellurite glasses. The O–Te–O, O–V–O, O–Li–O and O–O–O linkages have maxima in the ranges 86°–89°, 82°–87°, 80°–85° and at 59o, respectively. The structural analysis of tellurite glasses reveal significant short-range and medium-range disorder due to the existence of a wide range of Te–O and Te–Te distances in the first coordination shell.

Study in performance and morphology of polyamide 12 produced by selective laser sintering technology

2018 ◽  
Vol 24 (5) ◽  
pp. 813-820 ◽  
Author(s):  
Junjie Wu ◽  
Xiang Xu ◽  
Zhihao Zhao ◽  
Minjie Wang ◽  
Jie Zhang
Keyword(s):  
Selective Laser Sintering ◽  
Polarized Light ◽  
Chain Scission ◽  
High Energy ◽  
Laser Sintering ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Content Type ◽  
X Ray ◽  
Polyamide 12

Purpose The purpose of this paper is to investigate the effect of selective laser sintering (SLS) method on morphology and performance of polyamide 12. Design/methodology/approach Crystallization behavior is critical to the properties of semi-crystalline polymers. The crystallization condition of SLS process is much different from others. The morphology of polyamide 12 produced by SLS technology was investigated using scanning electron microscopy, polarized light microscopy, differential scanning calorimetry, X-ray diffraction and wide-angle X-ray diffraction. Findings Too low fill laser power brought about bad fusion of powders, while too high energy input resulted in bad performance due to chain scission of macromolecules. There were three types of crystal in the raw powder material, denoted as overgrowth crystal, ring-banded spherulite and normal spherulite. Originality/value In this work, SLS samples with different sintering parameters, as well as compression molding sample for the purpose of comparison, were made to study the morphology and crystal structure of sintered PA12 in detail.

Investigation of Residual Stress/Strain and Texture in a Large Dissimilar Metal Weld Using Synchrotron Radiation and Neutrons

2013 ◽  
Vol 772 ◽  
pp. 193-199 ◽  
Author(s):  
Carsten Ohms ◽  
Rene V. Martins
Keyword(s):  
Synchrotron Radiation ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Large Scale ◽  
High Energy ◽  
X Ray Diffraction ◽  
Butt Weld ◽  
X Ray ◽  
Component Size ◽  
Thin Slice

Bi-metallic piping welds are frequently used in light water nuclear reactors to connect ferritic steel pressure vessel nozzles to austenitic stainless steel primary cooling piping systems. An important aspect for the integrity of such welds is the presence of residual stresses. Measurement of these residual stresses presents a considerable challenge because of the component size and because of the material heterogeneity in the weld regions. The specimen investigated here was a thin slice cut from a full-scale bi-metallic piping weld mock-up. A similar mock-up had previously been investigated by neutron diffraction within a European research project called ADIMEW. However, at that time, due to the wall thickness of the pipe, stress and spatial resolution of the measurements were severely restricted. One aim of the present investigations by high energy synchrotron radiation and neutrons used on this thin slice was to determine whether such measurements would render a valid representation of the axial strains and stresses in the uncut large-scale structure. The advantage of the small specimen was, apart from the easier manipulation, the fact that measurement times facilitated a high density of measurements across large parts of the test piece in a reasonable time. Furthermore, the recording of complete diffraction patterns within the accessible diffraction angle range by synchrotron X-ray diffraction permitted mapping the texture variations. The strain and stress results obtained are presented and compared for the neutron and synchrotron X-ray diffraction measurements. A strong variation of the texture pole orientations is observed in the weld regions which could be attributed to individual weld torch passes. The effect of specimen rocking on the scatter of the diffraction data in the butt weld region is assessed during the neutron diffraction measurements.

Microstructure Evolution of a Fine Grain Al-50wt%Si Alloy Fabricated by High Energy Milling

2011 ◽  
Vol 479 ◽  
pp. 54-61 ◽  
Author(s):  
Fei Wang ◽  
Ya Ping Wang
Keyword(s):  
Grain Growth ◽  
Microstructure Evolution ◽  
Room Temperature ◽  
Milling Time ◽  
High Energy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Laser Method ◽  
X Ray ◽  
Fine Grain

Microstructure evolution of high energy milled Al-50wt%Si alloy during heat treatment at different temperature was studied. Scanning electron microscope (SEM) and X-ray diffraction (XRD) results show that the size of the alloy powders decreased with increasing milling time. The observable coarsening of Si particles was not seen below 730°C in the high energy milled alloy, whereas, for the alloy prepared by mixed Al and Si powders, the grain growth occurred at 660°C. The activation energy for the grain growth of Si particles in the high energy milled alloy was determined as about 244 kJ/mol by the differential scanning calorimetry (DSC) data analysis. The size of Si particles in the hot pressed Al-50wt%Si alloy prepared by high energy milled powders was 5-30 m at 700°C, which was significantly reduced compared to that of the original Si powders. Thermal diffusivity of the hot pressed Al-50wt%Si alloy was 55 mm2/s at room temperature which was obtained by laser method.

Single Crystal Wurtzitic Aluminum Nitride Growth on Silicon Using Supersonic Gas Jets

1995 ◽  
Vol 395 ◽  
Author(s):  
S. A. Ustin ◽  
L. Lauhon ◽  
K. A. Brown ◽  
D. Q. Hu ◽  
W. Ho
Keyword(s):  
Aluminum Nitride ◽  
Growth Rates ◽  
High Energy ◽  
X Ray Diffraction ◽  
Rutherford Back Scattering ◽  
X Ray ◽  
Supersonic Molecular Beam ◽  
Supersonic Beams ◽  
Wide Range

ABSTRACTHighly oriented aluminum nitride (0001) films have been grown on Si(001) and Si (111) substrates at temperatures between 550° C and 775° C with dual supersonic molecular beam sources. Triethylaluminum (TEA;[(C2H5)3Al]) and ammonia (NH3) were used as precursors. Hydrogen, helium, and nitrogen were used as seeding gases for the precursors, providing a wide range of possible kinetic energies for the supersonic beams due to the disparate masses of the seed gases. Growth rates of AIN were found to depend strongly on the substrate orientation and the kinetic energy of the incident precursor; a significant increase in growth rate is seen when seeding in hydrogen or helium as opposed to nitrogen. Growth rates were 2–3 times greater on Si(001) than on Si(111). Structural characterization of the films was done by reflection high energy electron diffraction (RHEED) and x-ray diffraction (XRD). X-ray rocking curve (XRC) full-width half-maxima (FWHM) were seen as small as 2.5°. Rutherford back scattering (RBS) was used to determine the thickness of the films and their chemical composition. Films were shown to be nitrogen rich, deviating from perfect stoichiometry by 10%–20%. Surface analysis was performed by Auger electron spectroscopy (AES).

The structure of oxide glasses studied by high-energy x-ray diffraction

2020 ◽  
Vol 61 (6) ◽  
pp. 233-238
Author(s):  
S. Kohara ◽  
◽  
N. Umesaki ◽  
H. Ohno ◽  
K. Suzuya ◽  
...  
Keyword(s):  
Neutron Diffraction ◽  
Structural Information ◽  
Structural Models ◽  
High Energy ◽  
Reverse Monte Carlo ◽  
Oxide Glasses ◽  
Neutron Diffraction Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Approaches To Study

The use of high‑energy x‑ray diffraction techniques with the latest generation synchrotron sources has created new approaches to study quantitatively the structure of noncrystalline materials. Recently, this technique has been combined with neutron diffraction at pulsed source to provide more detailed and reliable structural information not previously available. This article reviews and summarises recent results obtained from the high energy x‑ray diffraction on several oxide glasses, SiO2, B2O3 and PbSiO3, using bending magnet beamlines at SPring‑8. In particular, it addresses the structural models of the oxide glasses obtained by the reverse Monte Carlo (RMC) modelling technique using both the high energy x‑ray and neutron diffraction data.

X-ray Diffraction Study of Amorphous NixZr(100-x)-Alloys Prepared by Melt-Spinning

1991 ◽  
Vol 46 (11) ◽  
pp. 947-950
Author(s):  
W.-M. Kuschke ◽  
P. Lamparter ◽  
S. Steeb
Keyword(s):  
Melt Spinning ◽  
Pair Correlation ◽  
Nickel Concentration ◽  
Superconducting Transition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Coordination Numbers ◽  
Structure Factors ◽  
Wide Range ◽  
Good Agreement

AbstractAmorphous Ni-Zr-alloys can be prepared by melt-spinning within a wide range of composition. Studies by X-ray diffraction yielded structure factors, pair correlation functions, total coordination numbers and atomic distances in dependence on the nickel concentration in the range of 25 up to 45 atomic percent. The change of the total coordination number and atomic distances turned out to be linear with the composition in this range. This is in good agreement with the linear composition dependence of the superconducting transition temperature, magnetic susceptibility, crystallization temperature, and electrical resistivity in the investigated range of composition.

High-energy synchrotron X-ray diffraction measurements of simple bending of pseudoelastic NiTi shape memory alloy wires

2016 ◽  
Vol 31 (2) ◽  
pp. 104-109 ◽  
Author(s):  
Baozhuo Zhang ◽  
Marcus L. Young
Keyword(s):  
Phase Transformation ◽  
Shape Memory ◽  
High Energy ◽  
Bend Angle ◽  
Niti Shape Memory Alloy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Mechanical Bending ◽  
Xrd Patterns

Many technological applications of austenitic shape memory alloys (SMAs) involve cyclical mechanical loading and unloading in order to take advantage of pseudoelasticity. In this paper, we investigated the effect of mechanical bending of pseudoelastic NiTi SMA wires using high-energy synchrotron radiation X-ray diffraction (SR-XRD). Differential scanning calorimetry was performed to identify the phase transformation temperatures. Scanning electron microscopy images show that micro-cracks in compressive regions of the wire propagate with increasing bend angle, while tensile regions tend not to exhibit crack propagation. SR-XRD patterns were analyzed to study the phase transformation and investigate micromechanical properties. By observing the various diffraction peaks such as the austenite (200) and the martensite (${\bar 1}12$), (${\bar 1}03$), (${\bar 1}11$), and (101) planes, intensities and residual strain values exhibit strong anisotropy, depending upon whether the sample is in compression or tension during bending.

scholarly journals The migration mechanism of transition metal ions in LiNi0.5Mn1.5O4

2015 ◽  
Vol 3 (24) ◽  
pp. 13031-13038 ◽  
Author(s):  
Gui-Liang Xu ◽  
Yan Qin ◽  
Yang Ren ◽  
Lu Cai ◽  
Ke An ◽  
...  
Keyword(s):  
Transition Metal ◽  
Neutron Diffraction ◽  
Metal Ions ◽  
Transition Metal Ions ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Migration Mechanism

In situ high-energy X-ray diffraction and neutron diffraction were deployed to trace the migration of transition metal ions in LiNi0.5Mn1.5O4.

Structure of Zr-Cu and Zr-Ni Liquid Alloys Studied by High-Energy X-Ray Diffraction

2007 ◽  
Vol 561-565 ◽  
pp. 1349-1352 ◽  
Author(s):  
Akitoshi Mizuno ◽  
T. Kaneko ◽  
Seiichi Matsumura ◽  
Masahito Watanabe ◽  
Shinji Kohara ◽  
...  
Keyword(s):  
Liquid Structure ◽  
High Energy ◽  
Glass Forming Ability ◽  
Liquid Alloys ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Forming ◽  
Structure Factors ◽  
Asymmetric Shape ◽  
Second Peak

In order to obtain an insight into the high glass-forming ability of bulk metallic glasses, we have analyzed liquid structures of the Zr-Cu and the Zr-Ni binary alloys with different compositions. High-energy (E = 113 keV) x-ray diffraction experiments were carried out for the liquid alloys levitated by a conical nozzle levitation (CNL) technique. While a peculiar shoulder on the second peak was observed in the structure factors of the Zr-Cu liquid alloys, those of the Zr70Ni30 and the Zr50Ni50 liquids exhibit an asymmetric shape of the second peak. In addition, it was found that the effect of concentration variation in the liquid Zr-Ni alloys was significantly different from that of the liquid Zr-Cu alloys. The liquid structure analyses using the reverse Monte Carlo (RMC) simulation have clarified that a degree of the short-range correlation between the constituents in the liquids affects substantially the glass-forming ability of the binary Zr alloys.

Sign in / Sign up

Export Citation Format

Share Document