The passive properties of TA10 in Coca-Cola containing oral environment

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ming Liu ◽  
Jun Li ◽  
Danping Li ◽  
Lierui Zheng
Keyword(s):  
Corrosion Resistance ◽  
Passive Film ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Artificial Saliva ◽  
Corrosion Current ◽  
Content Type ◽  
Passive Behavior ◽  
Tooth Demineralization ◽  
Oral Environment

Purpose At present, carbonated drinks such as cola are especially favored by the younger generation. But because of its acid, it often leads to tooth demineralization, resulting in “cola tooth”. However, the influence of cola on the corrosion resistance of passive film of TiA10 alloy restorative materials is rarely reported. The purpose of this study was to analysis the corrosion resistance, composition of the passive film of TA10 alloy in different concentrations of Cola. Design/methodology/approach The passive behavior of TA10 alloy in artificial saliva (AS) and Cola was studied by means of potentiodynamic polarization, electrochemical impedance spectroscopy, cyclic voltammetry, Mott-Schottky techniques and combined with X-ray photoelectron spectroscopy and Auger electron spectroscopy (AES) surface analysis. Findings With the increase of cola content, the self-corrosion current density of the alloy increases sharply, and the corrosion resistance of the passive film is the best in AS, while Rp in cola is reduced to half of that in AS. The thickness of the passive film in AS, AS +cola and cola is about 9.5 nm, 7.5 nm and 6 nm, respectively. The passive film in cola has more defects and the carrier density is 1.55 times as high as that in AS. Cola can weaken the formation process of the protected oxide, promote the formation of high valence Ti-oxides and increase the content of Mo-oxides in the passive film. Originality/value These results have important guiding significance for the safe use of the alloy in the complex oral environments.

Effects of potassium silicate on corrosion behavior of dacromet coating

2019 ◽  
Vol 66 (6) ◽  
pp. 819-826
Author(s):  
Khashayar Tabi ◽  
Mansour Farzam ◽  
Davood Zaarei
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Automobile Industry ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Corrosion Current ◽  
Potassium Silicate ◽  
Coated Steel ◽  
Content Type ◽  
New Information

Purpose Potassium silicate sealer was applied on solvent-cleaned, acid-pickled, dacromet-coated steel to improve its corrosion resistance. The purpose of this paper is to study the corrosion behavior of dacromet-coated steel. Design/methodology/approach Potassium silicate sealer was applied on solvent-cleaned, acid-pickled, dacromet-coated steel to improve its corrosion resistance. Electrochemical impedance spectroscopy (EIS), potentiodynamic polarization, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and salt spray were carried out. SEM was used to study the morphological appearance of the surface. Findings The EIS behavior indicated that solvent-cleaned dacromet-coated steel sealed with potassium silicate showed that the corrosion current density was 2.664E − 5 A.cm2 which was reduced to 8.752E − 6 A.cm2 and the corrosion rate, which was 2.264E − 2 mm.year−1, was reduced to 7.438E − 3 mm.year−1 in NaCl 3.5 wt.per cent. EIS was used in NaCl 3.5 wt.%, and the Bode plot characteristics showed that the corrosion protection of solvent-cleaned, dacromet-coated steel was enhanced when sealed with potassium silicate. The EDS results of salt-sprayed, solvent-cleaned samples after 10 days indicated that the main corrosion products are composed of SiO2, ZnO and Al2O3. Research limitations/implications The detection of Li element in EDS was not possible because of the device limitation. Originality/value The current paper provides new information about the sealing properties of potassium silicate and its effects on the corrosion resistance of dacromet coating, which is widely used in many industries such as the automobile industry.

Corrosion resistance and characterization studies of calcium series chemical conversion film via green pretreatment on magnesium alloy

2016 ◽  
Vol 63 (6) ◽  
pp. 508-512
Author(s):  
Fengjing Wu ◽  
Xiaojuan Liu ◽  
Xin Xiao
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Electrochemical Impedance ◽  
Chemical Conversion ◽  
Corrosion Current ◽  
Organic Coating ◽  
Hazardous Substances ◽  
Surface Pretreatment ◽  
Content Type ◽  
Az80 Magnesium Alloy

Purpose Magnesium alloys, although valuable, are reactive and require protection before its application in many fields. The purpose of this study was to evaluate a novel anticorrosive chemical conversion film on AZ80 magnesium alloy by environmental-friendly calcium series surface pretreatment. Design/methodology/approach The corrosion resistance of the film was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy in 3.5 Wt.% NaCl solution. The surface morphologies, microstructure and composition of the film were investigated by scanning electron microscopy and energy-dispersive spectroscopy. Findings The corrosion current density of the calcium series film decreased by more than one order of magnitude as compared to that of the AZ80 magnesium alloy. The conversion film presented dry-mud morphology, and its thickness was estimated to be approximately 4 μm. The conversion film was highly hydrophilic, and the organic coating adhesion on treated AZ80 surface was approximately 13.5 MPa. Originality/value Excellent performance of the calcium-based chemical conversion film on Mg alloy was obtained, which does not contain heavy metals or fluorides and completely conforms to European RoHS (Restriction of Hazardous Substances) standard.

Corrosion Behavior of Zr53.5Cu26.5Ni5Al12Ag3 Bulk Amorphous Alloy in 3.5% NaCl Solution

2011 ◽  
Vol 299-300 ◽  
pp. 427-431
Author(s):  
Yun Li ◽  
Shi Zhi Shang ◽  
Ming Cheng ◽  
Liang Xu ◽  
Shi Hong Zhang
Keyword(s):  
Corrosion Resistance ◽  
Amorphous Alloy ◽  
Passive Film ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Bulk Amorphous Alloy ◽  
Nacl Solution ◽  
Current Densities ◽  
Resistance Decrease

The corrosion behavior of Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy in 3.5% NaCl solution was investigated by using potentiodynamic polarization experiments and electrochemical impedance spectroscopy (EIS). The results show that Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy has the better corrosion resistance than its corresponding crystal alloy. During the bath in the 3.5% NaCl solution at 25°C, Zr53.5Cu26.5Ni5Al12Ag3 alloy has the lower corrosion current density than the corresponding crystal alloy. After 100h, the corrosion current densities of Zr53.5Cu26.5Ni5Al12Ag3 and the corresponding crystal alloy are 3.8415×10-8A/cm2 and 5.2827×10-7A/cm2, respectively. The results of EIS test indicate that Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy has the excellent corrosion resistance because passive film with stable structure formed on the surface in 3.5% NaCl solution. With an increase in the immersion time, the passive film becomes thicker. It leads to impedance resistance and corrosion resistance decrease. The surface of Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy in 3.5% NaCl solution for 100h was analyzed by SEM and EDS. The results show that the corrosive pitting can be found at both the amorphous alloy and the corresponding crystal alloy. However, the amorphous alloy has the better corrosive pitting resistance than the crystal one because the corrosion products formed by selective dissolving of Zr and Al elements. Moreover, the addition of Ag element helps to improve the corrosion resistance of the amorphous alloy greatly.

Electrochemical Behavior of Titanium in Artificial Saliva: Influence of pH

2014 ◽  
Vol 40 (1) ◽  
pp. 3-10 ◽  
Author(s):  
Savithri Abey ◽  
Mathew T. Mathew ◽  
Damian J. Lee ◽  
Kent L. Knoernschild ◽  
Markus A. Wimmer ◽  
...  
Keyword(s):  
Passive Film ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Artificial Saliva ◽  
Pure Titanium ◽  
Corrosion Current ◽  
Nyquist Plot ◽  
Commercially Pure Titanium ◽  
Ph Values ◽  
Film Layer

Titanium is the most common material chosen for dental implants because it is highly corrosion resistant because it constantly reforms a protective passive film layer. The formation and composition of the passive film layer is dependent on the environmental conditions. If the stable oxide layer is damaged, the titanium surface underneath can corrode. The purpose of this study was to determine if basic corrosion of commercially pure titanium (CpTi) alloy in artificial saliva was affected by pH and to understand the corrosion kinetics/mechanisms of CpTi as a function of pH. In this study, titanium alloy discs were subjected to corrosion tests. Before the tests, all samples were cleaned and polished using standard metallographic preparation methods. Artificial saliva was used as the testing medium. The following pH values were tested: 3.0, 4.5, 6.0, 6.5, 7.5, and 9.0. Different pH values were achieved by adding lactic acid (acidic) or NaOH (basic) in appropriate amounts. Potentiodynamic curves indicated behavior change at each pH. In addition, the corrosion current density value determined from the potentiodynamic curve exhibited the poorest corrosion resistance for pH 7.5. The Nyquist plot (from the electrochemical impedance spectroscopy results) indicated that pH 7.5 had the poorest resistance. Scanning electron microscopy images indicated that pH levels of 6.5, 7.5, and 9.0 had considerable surface corrosion. The results showed that the media's pH significantly influenced the corrosion behavior of CpTi. The poor corrosion behavior at the neutral pHs invites some concerns and highlights the need for further study.

Preparation and characterization of a cerium conversion film on magnesium alloy

2015 ◽  
Vol 62 (4) ◽  
pp. 253-258 ◽  
Author(s):  
Jie Sun ◽  
Gang Wang
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Photoelectron Spectroscopy ◽  
Corrosion Current ◽  
Treatment Temperature ◽  
Conversion Coating ◽  
Conversion Coatings ◽  
Content Type ◽  
X Ray ◽  
Passivation Film

Purpose – The purpose of this paper was to prepare the cerium-based conversion coating on AZ91D magnesium alloy, and its compositions, micro-morphology, corrosion resistance and the chemical valence state of the film elements were investigated. Design/methodology/approach – The methodology comprised preparation of coatings at different temperatures, which then were characterized using scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, an electrochemistry workstation and by means of X-ray photoelectron spectroscopy. Findings – The conversion coating had a micro-cracked morphology. The conversion coatings were composed of MgO (or Mg-OH), CeO2 and Ce2O3. The best corrosion resistance of the cerium passivation film appeared when the treatment temperature was about 35°C. Originality/value – The corrosion current densities of conversion coatings were lower by one to two orders of magnitude than the corrosion current density of the blank sample. The rare earth passivation coating prepared under the best condition could reduce the corrosion current to 3.548 × 10−6 A/cm2.

scholarly journals Corrosion Resistance of a Plasma-Oxidized Ti6Al4V Alloy for Dental Applications

Coatings ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1136
Author(s):  
N. Velazquez-Torres ◽  
J. Porcayo-Calderon ◽  
H. Martinez-Valencia ◽  
R. Lopes-Cecenes ◽  
I. Rosales-Cadena ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Polarization Resistance ◽  
Electrochemical Impedance ◽  
Artificial Saliva ◽  
Corrosion Current ◽  
Ti6al4v Alloy ◽  
Free Corrosion Potential ◽  
Density Values ◽  
Eis Measurements ◽  
Dental Applications

A Ti6Al4V alloy was plasma-oxidized at 600 °C during 1, 2, 3, 5 and 8 h and corroded in an artificial saliva solution. Electrochemical evaluation was performed by using potentiodynamic polarization curves, linear polarization resistance (LPR), and electrochemical impedance spectroscopy (EIS) measurements during 100 h. Corroded specimens were characterized by using Raman spectroscopy and scanning electronic microscopy (SEM). All tests indicated that the highest corrosion resistance was obtained for specimen oxidized during 3 h since the noblest free corrosion potential, lowest passive and corrosion current density values, as well as the highest polarization resistance values were obtained under these circumstances. EIS measurements indicated that the highest impedance and phase angle values obtained for this specimen exhibited a high capacitive behavior typical of a very compact passive film.

Strengthened passivation and mechanism of 316L stainless steel in hot diluted sulfuric acid solution by connecting to Pd electrode

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Huizhong Zhang ◽  
Yu Zuo ◽  
Pengfei Ju ◽  
Jian Zhang ◽  
Xuhui Zhao ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Passive Film ◽  
Photoelectron Spectroscopy ◽  
Steel Surface ◽  
Electrochemical Impedance ◽  
Impedance Spectrum ◽  
Electrochemical Impedance Spectrum ◽  
Stainless Steel Surface ◽  
Content Type ◽  
316 L Stainless Steel

Purpose The purpose of this paper is to study the variations of composition and properties of the passive film on 316 L stainless steel surface in 80°C, 0.5 mol L-1 H2SO4 + 2 mg L-1 NaF solution, is helpful to understand the mechanisms of corrosion resistancethe of plated Pd on 316 L ss. Design/methodology/approach The variations of composition and properties of the passive film on 316 L stainless steel surface in 80°C, 0.5 mol L-1 H2SO4 + 2 mg L-1 NaF solution after connected to Pd electrode were studied with methods of potential monitor, X-ray photoelectron spectroscopy analysis and electrochemical impedance spectrum (EIS) measurement. Findings By connecting to a Pd electrode, the potential of the SS sample increased from the active region to the passive region. By connecting to the Pd electrode, the contents of Cr, Cr(OH)3 and Fe3O4 in passive film increased obviously. With increased Pd/SS area ratio, the Cr(OH)3 content in passive film increased but the Fe3O4 content changed little. The results show that after connecting to Pd the corrosion resistance of the passive film on 316 L stainless steel increases obviously, which may be attributed to the more compact passive film because of higher Cr, Cr(OH)3 and Fe3O4 contents and less point defects in the film. Originality/value The effects and mechanism of Pd on passivation of SS was studied.

scholarly journals Change of n-type to p-type conductivity of the semiconductor passive film on N-steel: Enhancement of the pitting corrosion resistance

2013 ◽  
Vol 78 (12) ◽  
pp. 2053-2067 ◽  
Author(s):  
Mirjana Metikos-Hukovic ◽  
Zoran Grubac ◽  
Sasha Omanovic
Keyword(s):  
Corrosion Resistance ◽  
Passive Film ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Surface Film ◽  
Barrier Properties ◽  
Electrochemical Treatment ◽  
Before And After ◽  
Testing Solution ◽  
P Type

The electrochemically-assisted modification of the N-austenitic stainless steel (ASS N25) surface was successfully employed to improve barrier properties of the passive film in a chloride containing solution. The chemical composition, electronic and barrier properties of the surface film before and after the electrochemical treatment were examined using X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). Electrochemical measurements were carried out in a corrosion testing solution. The excellent corrosion resistance (both pitting and general) of the N-steel?s modified surface was discussed according to the Mott-Schottky analysis of the interfacial capacitance of the space charge layer and EIS results. The conductivity change of the surface film from an n- to a p-type in the pitting susceptible region was explained using the XPS analysis and semiconducting properties of the film.

Evaluation of the corrosion behavior of AZ31 magnesium alloy with different protein concentrations

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yucong Ma ◽  
Mohd Talha ◽  
Qi Wang ◽  
Zhonghui Li ◽  
Yuanhua Lin
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Surface Film ◽  
Energy Dispersive Spectrometer ◽  
Inhibitory Effect ◽  
Corrosion Process ◽  
High Concentration ◽  
Content Type ◽  
Atomic Force

Purpose The purpose of this paper is to study systematically the corrosion behavior of AZ31 magnesium (Mg) alloy with different concentrations of bovine serum albumin (BSA) (0, 0.5, 1.0, 1.5, 2.0 and 5.0 g/L). Design/methodology/approach Electrochemical impedance spectroscopy and potential dynamic polarization tests were performed to obtain corrosion parameters. Scanning electrochemical microscopy (SECM) was used to analyze the local electrochemical activity of the surface film. Atomic force microscope (AFM), Scanning electron microscope-Energy dispersive spectrometer and Fourier transform infrared spectroscopy were used to determine the surface morphology and chemical composition of the surface film. Findings Experimental results showed the presence of BSA in a certain concentration range (0 to 2.0 g/L) has a greater inhibitory effect on the corrosion of AZ31, however, the presence of high-concentration BSA (5.0 g/L) would sharply reduce the corrosion resistance. Originality/value When the concentration of BSA is less than 2.0 g/L, the corrosion resistance of AZ31 enhances with the concentration. The adsorption BSA layer will come into being a physical barrier to inhibit the corrosion process. However, high-concentration BSA (5.0 g/L) will chelate with dissolved metal ions (such as Mg and Ni) to form soluble complexes, which increases the roughness of the surface and accelerates the corrosion process.

Material Property of a Passive Oxide Formed on Alloy 600

2007 ◽  
Vol 26-28 ◽  
pp. 937-940 ◽  
Author(s):  
Dong Jin Kim ◽  
Hyuk Chul Kwon ◽  
Seong Sik Hwang ◽  
Hong Pyo Kim
Keyword(s):  
Corrosion Resistance ◽  
Oxide Layer ◽  
Passive Film ◽  
Electrochemical Impedance ◽  
Oxide Films ◽  
Oxide Thickness ◽  
Solution Temperature ◽  
Alloy 600 ◽  
Pressurized Water ◽  
Electrochemical Behaviors

Alloy 600 is used as a material for a steam generator tubing in pressurized water reactors(PWR) due to its high corrosion resistance under a PWR environment. In spite of its corrosion resistance, a stress corrosion cracking(SCC) has occurred on the primary side as well as the secondary side of a tubing. It is known that a SCC is related to the electrochemical behaviors of an anodic dissolution and a passivation of a bare surface of metals and alloys. Therefore in the present work, the passive oxide films on Alloy 600 have been investigated as a function of the solution temperature by using a potentiodynamic polarization, electrochemical impedance spectroscopy and a TEM, equipped with EDS. Moreover the semiconductive property was evaluated by using the Mott-Schottky relation. It was found that the passivity depends on the chemical composition and the densification of the oxide film rather than the oxide thickness. As the solution temperature of 0.5M H3BO3 increased, the thickness of the passive film increased but the oxide resistance of the passive film was decreased, indicating that the measured current in the passive region of the potentiodynamic curve is closely related to the stability of the passive film rather than the oxide thickness. It was found that the oxide films were composed of an outer oxide layer with a lower resistance and an inner oxide layer with a relatively higher resistance. From the Mott-Schottky relation, the oxide formed at 300oC showed a p-type semiconductor property unlike the n-type oxide films up to 250oC.

Sign in / Sign up

Export Citation Format

Share Document