Corrosion Behavior of Zr53.5Cu26.5Ni5Al12Ag3 Bulk Amorphous Alloy in 3.5% NaCl Solution

2011 ◽  
Vol 299-300 ◽  
pp. 427-431
Author(s):  
Yun Li ◽  
Shi Zhi Shang ◽  
Ming Cheng ◽  
Liang Xu ◽  
Shi Hong Zhang
Keyword(s):  
Corrosion Resistance ◽  
Amorphous Alloy ◽  
Passive Film ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Bulk Amorphous Alloy ◽  
Nacl Solution ◽  
Current Densities ◽  
Resistance Decrease

The corrosion behavior of Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy in 3.5% NaCl solution was investigated by using potentiodynamic polarization experiments and electrochemical impedance spectroscopy (EIS). The results show that Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy has the better corrosion resistance than its corresponding crystal alloy. During the bath in the 3.5% NaCl solution at 25°C, Zr53.5Cu26.5Ni5Al12Ag3 alloy has the lower corrosion current density than the corresponding crystal alloy. After 100h, the corrosion current densities of Zr53.5Cu26.5Ni5Al12Ag3 and the corresponding crystal alloy are 3.8415×10-8A/cm2 and 5.2827×10-7A/cm2, respectively. The results of EIS test indicate that Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy has the excellent corrosion resistance because passive film with stable structure formed on the surface in 3.5% NaCl solution. With an increase in the immersion time, the passive film becomes thicker. It leads to impedance resistance and corrosion resistance decrease. The surface of Zr53.5Cu26.5Ni5Al12Ag3 bulk amorphous alloy in 3.5% NaCl solution for 100h was analyzed by SEM and EDS. The results show that the corrosive pitting can be found at both the amorphous alloy and the corresponding crystal alloy. However, the amorphous alloy has the better corrosive pitting resistance than the crystal one because the corrosion products formed by selective dissolving of Zr and Al elements. Moreover, the addition of Ag element helps to improve the corrosion resistance of the amorphous alloy greatly.

scholarly journals Assessment of nickel titanium and beta titanium corrosion resistance behavior in fluoride and chloride environments

2013 ◽  
Vol 83 (5) ◽  
pp. 864-869 ◽  
Author(s):  
Elisa J. Kassab ◽  
José Ponciano Gomes
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Fluoride Concentration ◽  
Nickel Titanium ◽  
Localized Corrosion ◽  
General Corrosion ◽  
Nacl Solution ◽  
Galvanic Coupling ◽  
Beta Titanium

ABSTRACT Objective: To assess the influence of fluoride concentration on the corrosion behavior of nickel titanium (NiTi) superelastic wire and to compare the corrosion resistance of NiTi with that of beta titanium alloy in physiological solution with and without addition of fluoride. Materials and Methods: NiTi corrosion resistance was investigated through electrochemical impedance spectroscopy and anodic polarization in sodium chloride (NaCl 0.15 M) with and without addition of 0.02 M sodium fluoride (NaF), and the results were compared with those associated with beta titanium. The influence of fluoride concentration on NiTi corrosion behavior was assessed in NaCl (0.15 M) with and without 0.02, 0.04, 0.05, 0.07, and 0.12 M NaF solution. Galvanic corrosion between NiTi and beta titanium were investigated. All samples were characterized by scanning electron microscopy. Results: Polarization resistance decreased when NaF concentration was increased, and, depending on NaF concentration, NiTi can suffer localized or generalized corrosion. In NaCl solution with 0.02 M NaF, NiTi suffer localized corrosion, while beta titanium alloys remained passive. Current values near zero were observed by galvanic coupling of NiTi and beta titanium. Conclusions: There is a decrease in NiTi corrosion resistance in the presence of fluoride. The corrosion behavior of NiTi alloy depends on fluoride concentration. When 0.02 and 0.04 M of NaF were added to the NaCl solution, NiTi presented localized corrosion. When NaF concentration increased to 0.05, 0.07, and 0.12 M, the alloy presented general corrosion. NiTi corrosion resistance behavior is lower than that of beta titanium. Galvanic coupling of these alloys does not increase corrosion rates.

Improved Corrosion Resistance and Increased Hardness of Copper Substrates from Cu-Ni/Ni-P Composite Coatings

MRS Advances ◽  
2020 ◽  
Vol 5 (40-41) ◽  
pp. 2129-2137 ◽  
Author(s):  
Wenwen Dou ◽  
Wen Li ◽  
Yuchen Cai ◽  
Mengyao Dong ◽  
Xiaojing Wang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Copper Substrate ◽  
Electrolytic Deposition ◽  
Deposition Method ◽  
Nacl Solution ◽  
Current Densities ◽  
Superior Corrosion Resistance ◽  
Deposition Conditions

ABSTRACTTo improve the corrosion resistance and to increase the hardness of copper substrate in marine environment, the Cu-Ni/Ni-P composite coatings were prepared on the copper substrate using the galvanostatic electrolytic deposition method. The deposition current densities were explored to find the optimized deposition conditions for forming the composite coatings. Corrosion resistance properties were analyzed using the polarization curves and electrochemical impedance spectroscopy (EIS). Considering the corrosion resistance and hardness, the −20 mA/cm2 was selected to deposit Cu-Ni coatings on copper substrate and the −30 mA/cm2 was selected to deposit Ni-P coating on the Cu-Ni layer. The Cu-Ni/Ni-P composite coatings not only exhibited superior corrosion resistance compared to single Cu-Ni coating in 3.5 wt.% NaCl solution, but also showed much better mechanical properties than single Cu-Ni coating.

scholarly journals A microstructural and corrosion resistance study of (Zr, Si, Ti)N-Ni coatings produced through co-sputtering

DYNA ◽  
2018 ◽  
Vol 85 (207) ◽  
pp. 192-197 ◽  
Author(s):  
Estrella Natali Borja-Goyeneche ◽  
Jhon Jairo Olaya-Florez
Keyword(s):  
Corrosion Resistance ◽  
Nickel Content ◽  
Corrosion Current ◽  
Nacl Solution ◽  
X Ray Diffraction ◽  
X Ray ◽  
X Ray Scattering ◽  
Current Densities ◽  
Fcc Phase

This work researches the influence of the nickel content on the structural and anticorrosive properties of ZrSiTiN films deposited by means of reactive co-sputtering on alloys of Ti6Al4V. The morphology and structure were analyzed by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD), and the chemical composition was identified via X-ray scattering spectroscopy (EDS). The corrosion resistance was studied using potentiodynamic polarization (PP) tests employing a 3.5% by weight NaCl solution. In the films, an increase of Ni up to 6.97 at% was observed, while in XRD the FCC phase of (Zr, Ti) N was identified, with a mixed orientation in planes (111) and (200), which tended to diminish with the increase of Ni. Finally, with the addition of Ni, the corrosion current densities were reduced from 5.56 𝑥 10−8 to 2.64 𝑥 10−9 𝐴/𝑐m2. The improvement in the corrosion resistance is due to the effect of the Ni on the microstructure of the system (Zr, Ti) N, which can improve the quality of the passive film and prevent crystalline defects and corrosion zones.

Effects of potassium silicate on corrosion behavior of dacromet coating

2019 ◽  
Vol 66 (6) ◽  
pp. 819-826
Author(s):  
Khashayar Tabi ◽  
Mansour Farzam ◽  
Davood Zaarei
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Automobile Industry ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Corrosion Current ◽  
Potassium Silicate ◽  
Coated Steel ◽  
Content Type ◽  
New Information

Purpose Potassium silicate sealer was applied on solvent-cleaned, acid-pickled, dacromet-coated steel to improve its corrosion resistance. The purpose of this paper is to study the corrosion behavior of dacromet-coated steel. Design/methodology/approach Potassium silicate sealer was applied on solvent-cleaned, acid-pickled, dacromet-coated steel to improve its corrosion resistance. Electrochemical impedance spectroscopy (EIS), potentiodynamic polarization, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and salt spray were carried out. SEM was used to study the morphological appearance of the surface. Findings The EIS behavior indicated that solvent-cleaned dacromet-coated steel sealed with potassium silicate showed that the corrosion current density was 2.664E − 5 A.cm2 which was reduced to 8.752E − 6 A.cm2 and the corrosion rate, which was 2.264E − 2 mm.year−1, was reduced to 7.438E − 3 mm.year−1 in NaCl 3.5 wt.per cent. EIS was used in NaCl 3.5 wt.%, and the Bode plot characteristics showed that the corrosion protection of solvent-cleaned, dacromet-coated steel was enhanced when sealed with potassium silicate. The EDS results of salt-sprayed, solvent-cleaned samples after 10 days indicated that the main corrosion products are composed of SiO2, ZnO and Al2O3. Research limitations/implications The detection of Li element in EDS was not possible because of the device limitation. Originality/value The current paper provides new information about the sealing properties of potassium silicate and its effects on the corrosion resistance of dacromet coating, which is widely used in many industries such as the automobile industry.

Effect of Heat Treatments on Stress Corrosion Behavior of 7050 Al Alloys in 3.5% NaCl Solution

2016 ◽  
Vol 877 ◽  
pp. 543-549
Author(s):  
Wei Wei Ren ◽  
Xing Feng Zhan ◽  
Lin Chi Zou ◽  
Qiang Li ◽  
Jun Feng Chen
Keyword(s):  
Corrosion Resistance ◽  
Strain Rate ◽  
Stress Corrosion ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Heat Treatments ◽  
Al Alloys ◽  
Slow Strain Rate ◽  
Nacl Solution ◽  
Stress Corrosion Resistance

Effect of heat treatments on the stress corrosion behavior of 7050 Al alloys in 3.5% NaCl solution has been investigated using slow strain rate tensile (SSRT) test. During the slow strain rate tensile process, electrochemical impedance spectroscopy (EIS) in real time was carried out to characterize the electrochemical behavior for different tempers 7050 Al alloys. The investigation shows that both the stress corrosion resistance of 7050 Al alloys is controlled by heat treatments due to the different precipitates state. The improvement of stress corrosion resistance is contributed to the tiny precipitates in matrix which are beneficial to corrosion potential and maintain passivation, and precipitates discontinuous distribution at grain boundary which obstruct intergranular crack connection. Moreover, base on the results, we find out retrogression and re-aging (RRA, i.e., T6 + 200 °C/ retrogression + water quench + T6) increases both tensile strength and stress corrosion resistance. The optimized of retrogression time is 30 minutes.

The passive properties of TA10 in Coca-Cola containing oral environment

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ming Liu ◽  
Jun Li ◽  
Danping Li ◽  
Lierui Zheng
Keyword(s):  
Corrosion Resistance ◽  
Passive Film ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Artificial Saliva ◽  
Corrosion Current ◽  
Content Type ◽  
Passive Behavior ◽  
Tooth Demineralization ◽  
Oral Environment

Purpose At present, carbonated drinks such as cola are especially favored by the younger generation. But because of its acid, it often leads to tooth demineralization, resulting in “cola tooth”. However, the influence of cola on the corrosion resistance of passive film of TiA10 alloy restorative materials is rarely reported. The purpose of this study was to analysis the corrosion resistance, composition of the passive film of TA10 alloy in different concentrations of Cola. Design/methodology/approach The passive behavior of TA10 alloy in artificial saliva (AS) and Cola was studied by means of potentiodynamic polarization, electrochemical impedance spectroscopy, cyclic voltammetry, Mott-Schottky techniques and combined with X-ray photoelectron spectroscopy and Auger electron spectroscopy (AES) surface analysis. Findings With the increase of cola content, the self-corrosion current density of the alloy increases sharply, and the corrosion resistance of the passive film is the best in AS, while Rp in cola is reduced to half of that in AS. The thickness of the passive film in AS, AS +cola and cola is about 9.5 nm, 7.5 nm and 6 nm, respectively. The passive film in cola has more defects and the carrier density is 1.55 times as high as that in AS. Cola can weaken the formation process of the protected oxide, promote the formation of high valence Ti-oxides and increase the content of Mo-oxides in the passive film. Originality/value These results have important guiding significance for the safe use of the alloy in the complex oral environments.

Effect of Coating Thickness on the Corrosion Behavior of Galvanized Steel in 3.5 % NaCl Solution

2021 ◽  
Vol 882 ◽  
pp. 35-49
Author(s):  
A.D. Vishwanatha ◽  
Bijayani Panda ◽  
J.N. Balaraju ◽  
Preeti Prakash Sahoo ◽  
P. Shreyas
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Product ◽  
Corrosion Behavior ◽  
Coating Thickness ◽  
Electrochemical Impedance ◽  
Immersion Test ◽  
Carbon Steels ◽  
Galvanized Steel ◽  
Uniform Corrosion ◽  
Nacl Solution

Corrosion behavior of three carbon steels with increasing galvanized coating thickness of 5.6, 8.4 and 19.2 μm named as T1, T2 and T3, respectively, was studied by immersion test, potentiodynamic polarization and electrochemical impedance spectroscopy in freely aerated 3.5% NaCl solution. The major phase in the corrosion product of all the samples after immersion test was found to be zincite, as determined by X-Ray Diffraction and Fourier Transform Infrared Spectroscopy techniques. The corrosion product on sample T1was well adhered and was compact in most regions. Samples T2 and T3 showed porous and non-adherent growth of corrosion product. Corrosion rates were found to increase with increasing coating thickness. The impedance provided by the coating as well as the substrate was the highest for the sample with thinnest coating (T1). The early exposure of the underlying steel in sample T1 resulted in higher corrosion resistance, which was probably due to the combined effect of zinc corrosion products and Fe-Zn alloy layer. Higher amount of protective γ-FeOOH as well as compact corrosion product could have also improved the corrosion resistance of sample T1. Although the average uniform corrosion resistance was higher for T1, the localized pitting corrosion was also observed, probably due to the thin galvanized layer.

Electrochemical Behavior of Titanium in Artificial Saliva: Influence of pH

2014 ◽  
Vol 40 (1) ◽  
pp. 3-10 ◽  
Author(s):  
Savithri Abey ◽  
Mathew T. Mathew ◽  
Damian J. Lee ◽  
Kent L. Knoernschild ◽  
Markus A. Wimmer ◽  
...  
Keyword(s):  
Passive Film ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Artificial Saliva ◽  
Pure Titanium ◽  
Corrosion Current ◽  
Nyquist Plot ◽  
Commercially Pure Titanium ◽  
Ph Values ◽  
Film Layer

Titanium is the most common material chosen for dental implants because it is highly corrosion resistant because it constantly reforms a protective passive film layer. The formation and composition of the passive film layer is dependent on the environmental conditions. If the stable oxide layer is damaged, the titanium surface underneath can corrode. The purpose of this study was to determine if basic corrosion of commercially pure titanium (CpTi) alloy in artificial saliva was affected by pH and to understand the corrosion kinetics/mechanisms of CpTi as a function of pH. In this study, titanium alloy discs were subjected to corrosion tests. Before the tests, all samples were cleaned and polished using standard metallographic preparation methods. Artificial saliva was used as the testing medium. The following pH values were tested: 3.0, 4.5, 6.0, 6.5, 7.5, and 9.0. Different pH values were achieved by adding lactic acid (acidic) or NaOH (basic) in appropriate amounts. Potentiodynamic curves indicated behavior change at each pH. In addition, the corrosion current density value determined from the potentiodynamic curve exhibited the poorest corrosion resistance for pH 7.5. The Nyquist plot (from the electrochemical impedance spectroscopy results) indicated that pH 7.5 had the poorest resistance. Scanning electron microscopy images indicated that pH levels of 6.5, 7.5, and 9.0 had considerable surface corrosion. The results showed that the media's pH significantly influenced the corrosion behavior of CpTi. The poor corrosion behavior at the neutral pHs invites some concerns and highlights the need for further study.

Corrosion Behavior of Cu50Zr40Ti10 Metallic Glass in HCl and NaCl

2013 ◽  
Vol 643 ◽  
pp. 33-36
Author(s):  
Wei Ke An ◽  
An Hui Cai ◽  
Guo Jun Zhou ◽  
Yun Luo ◽  
Tie Lin Li ◽  
...  
Keyword(s):  
Metallic Glass ◽  
Corrosion Behavior ◽  
Corrosion Potential ◽  
Chloride Ion ◽  
Corrosion Current ◽  
Ion Concentration ◽  
Nacl Solution ◽  
Current Densities

The corrosion behavior of Cu50Zr40Ti10 (at. %) in HCl and NaCl solutions was investigated. The corrosion current densities icorr in HCl and NaCl solutions increase with increasing Clconcentration when the Cl- concentration is <0.5 molL-1, then continuously increase in the former and decrease in the latter. The icorr is larger in the latter than in the former when the Clconcentration is <0.5 molL-1, while inversely for in 1 molL-1 Cl- solution. The corrosion potential Ecorr decreases with increasing Cl- concentration in HCl. However, the change of the Ecorr vs. the chloride ion concentration in NaCl solution appears down-up-down.

scholarly journals Corrosion behavior of Ti/Al laminate composites as electrode of chlor-alkali electrolysis

2020 ◽  
Vol 29 ◽  
pp. 2633366X2092088
Author(s):  
Lixia Wang ◽  
Limin Sun ◽  
Yang Cao ◽  
Jing Shen
Keyword(s):  
Corrosion Behavior ◽  
High Performance ◽  
Electrochemical Impedance ◽  
Intermetallic Phase ◽  
Electricity Consumption ◽  
Corrosion Current ◽  
Electrode System ◽  
Nacl Solution ◽  
Electrochemical Tests ◽  
Anode Electrode

High-performance electrodes can solve problems of high voltage and large electricity consumption existing in chlor-alkali industry. A Ti/Al laminate composite (named as Ti/Al-LC) with three-layered structure (Ti/Al3Ti/Ti) is prepared as a new type of anode electrode for chlor-alkali electrolysis. Scanning electron microscope observation shows that the Ti/Al-LC is composited of a thicker inner layer with thickness about 700 µm and two thinner outer layers with thickness about 300 µm. From the X-ray diffraction pattern, it is known that the outer layers consisted of α-Ti and β-Ti phases, while the inner layer consisted of Al3Ti intermetallic phase. A saturated sodium chloride (NaCl) solution at 70°C is purposely chosen as the corrosion electrolyte to analyze the corrosion behavior of Ti/Al-LC as anode electrode for chlor-alkali electrolysis. Electrochemical tests, including potentiodynamic polarization and electrochemical impedance spectroscopy measurements, on a three-electrode system indicate that the Ti/Al-LC has a low corrosion rate with corrosion current density of 1.94 µA cm−2 and stable surface passive film in saturated NaCl solution at 70°C.

Sign in / Sign up

Export Citation Format

Share Document