Investigation on aqua-ammonia based solar cooling cogeneration plant

2016 ◽  
Vol 27 (1) ◽  
pp. 36-44 ◽  
Author(s):  
R. Shankar ◽  
T. Srinivas
Keyword(s):  
Climatic Conditions ◽  
Working Fluid ◽  
Fluid Mixture ◽  
Content Type ◽  
Power Cycle ◽  
Solar Cooling ◽  
Atmosphere Temperature ◽  
Solar Thermal Cooling ◽  
Thermal Cooling ◽  
Cogeneration Cycle

Purpose – The proposed solar thermal cooling cogeneration cycle is well suited for industrial as well as domestic needs and it eliminates need of electricity for refrigeration system. The purpose of this paper is to integrate power and cooling to minimize the energy usage. Design/methodology/approach – The proposed plant has double turbine with superheater and reheater to extract more energy, operating on single generator. The saturated refrigerant from the exit of the generator is used to run the primary turbine and the exit mass of refrigerant is split into 50:50 cooling to power ratio. Findings – It produces additional power of 24 kW at absorber concentration of 0.42 and turbine inlet concentration of 0.95, with separator temperature of 145°C and atmosphere temperature of 30°C. Research limitations/implications – The proposed cooling cogeneration cycle is possible to run on all the refrigerant working fluid mixture and it overcomes the problem of Goswami cycle which is not possible to run in hot climatic countries. Originality/value – The cycle can operate individually as refrigeration cycle, power cycle and both and it will run all climatic conditions.

Comparative Analysis of Solar Thermal Cooling and Solar Photovoltaic Cooling Systems

2011 ◽  
Author(s):  
N. Fumo ◽  
V. Bortone ◽  
J. C. Zambrano
Keyword(s):  
Energy Consumption ◽  
Fossil Fuels ◽  
Cooling System ◽  
Solar Thermal ◽  
Solar Photovoltaic ◽  
Solar Thermal Energy ◽  
Cooling Systems ◽  
Solar Cooling ◽  
Solar Thermal Cooling ◽  
Thermal Cooling

The Energy Information Administration of the United States Department of Energy projects that more than 80% of the energy consumption of the U.S. by 2035 will come from fossil fuels. This projection should be the fuel to promote projects related to renewable energy in order to reduce energy consumption from fossil fuels to avoid their undesirable consequences such as carbon dioxide emissions. Since solar radiation match pretty well building cooling demands, solar cooling systems will be an important factor in the next decades to meet or exceed the green gases reduction that will be demanded by the society and regulations in order to mitigate environmental consequences such as global warming. Solar energy can be used as source of energy to produce cooling through different technologies. Solar thermal energy applies to technology such as absorption chillers and desiccant cooling, while electricity from solar photovoltaic can be used to drive vapor compression electric chillers. This study focuses on the comparison of a Solar Thermal Cooling System that uses an absorption chiller driven by solar thermal energy, and a Solar Photovoltaic Cooling System that uses a vapor compression system (electric chiller) driven by solar electricity (solar photovoltaic system). Both solar cooling systems are compared against a standard air cooled cooling system that uses electricity from the grid. The models used in the simulations to obtain the results are described in the paper along with the parameters (inputs) used. Results are presented in two figures. Each figure has one curve for the Solar Thermal Cooling System and one for the Solar Photovoltaic Cooling System. One figure allows estimation of savings calculated based the net present value of energy consumption cost. The other figure allows estimating primary energy consumption reduction and emissions reduction. Both figures presents the result per ton of refrigeration and as a function of area of solar collectors or/and area of photovoltaic modules. This approach to present the result of the simulations of the systems makes these figures quite general. This means that the results can be used to compare both solar cooling systems independently of the cooling demand (capacity of the system), as well as allow the analysis for different sizes of the solar system used to harvest the solar energy (collectors or photovoltaic modules).

Comparative Analysis of Solar Thermal Cooling and Solar Photovoltaic Cooling Systems

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
N. Fumo ◽  
V. Bortone ◽  
J. C. Zambrano
Keyword(s):  
Energy Consumption ◽  
Fossil Fuels ◽  
Cooling System ◽  
Solar Thermal ◽  
Solar Photovoltaic ◽  
Solar Thermal Energy ◽  
Cooling Systems ◽  
Solar Cooling ◽  
Solar Thermal Cooling ◽  
Thermal Cooling

The Energy Information Administration of the United States Department of Energy projects that more than 80% of the energy consumption of the U.S. by 2035 will come from fossil fuels. This projection should be the fuel to promote projects related to renewable energy in order to reduce energy consumption from fossil fuels to avoid their undesirable consequences such as carbon dioxide emissions. Since solar radiation match pretty well building cooling demands, solar cooling systems will be an important factor in the next decades to meet or exceed the green gases reduction that will be demanded by the society and regulations in order to mitigate environmental consequences such as global warming. Solar energy can be used as source of energy to produce cooling through different technologies. Solar thermal energy applies to technology such as absorption chillers and desiccant cooling, while electricity from solar photovoltaic can be used to drive vapor compression electric chillers. This study focuses on the comparison of a solar thermal cooling system that uses an absorption chiller driven by solar thermal energy, and a solar photovoltaic cooling system that uses a vapor compression system (electric chiller) driven by solar electricity (solar photovoltaic system). Both solar cooling systems are compared against a standard air cooled cooling system that uses electricity from the grid. The models used in the simulations to obtain the results are described in the paper along with the parameters (inputs) used. Results are presented in two figures. Each figure has one curve for the solar thermal cooling system and one for the solar photovoltaic cooling system. One figure allows estimation of savings calculated based the present value of discounted energy consumption cost. The other figure allows estimating primary energy consumption reduction and emissions reduction. Both figures presents the result per ton of refrigeration and as a function of area of solar collectors or/and area of photovoltaic modules. This approach to present the result of the simulations of the systems makes these figures quite general. This means that the results can be used to compare both solar cooling systems independently of the cooling demand (capacity of the system), as well as allow the analysis for different sizes of the solar system used to harvest the solar energy (collectors or photovoltaic modules).

scholarly journals Evaluation of Coupling PV and Air Conditioning vs. Solar Cooling Systems—Case Study from Jordan

2021 ◽  
Vol 11 (2) ◽  
pp. 511
Author(s):  
Aiman Albatayneh ◽  
Mustafa Jaradat ◽  
Murad Al-Omary ◽  
Maha Zaquot
Keyword(s):  
Air Conditioning ◽  
Cooling System ◽  
Economic Feasibility ◽  
Solar Thermal ◽  
Cooling Systems ◽  
Solar Cooling ◽  
Solar Thermal Cooling ◽  
Air Conditioning Systems ◽  
Solar Cooling System ◽  
Thermal Cooling

When they were first conceived, solar cooling systems were designed to be cost-effective and environmentally safe alternatives for the majority of the developing nations that are characterised by their hot climates in contrast with the traditional air conditioning systems powered by electricity that is produced from fossil fuel resources. Nevertheless, developments in photovoltaic (PV) and air-conditioning technologies have impacted on the prospects of solar cooling systems. This study examined two different options: a coupled PV and air conditioner system and a solar cooling system (absorption chillers where thermal energy is provided by solar collectors) for a specific developing country located in the Eastern Mediterranean region whose climate is hot and dry (Jordan). The cooling system comprised a pair of cooled multistage compression, both of which were 700 kW, while the PV system’s size was 2.1 MWp, the utility grid connection was a 0.4 kV 50 Hz net meter (2 m) and it was anticipated that 3300 MWh/year would be generated. The solar cooling system operated at a maximum coefficient of performance (COP) of 0.79 and had an actual recorded COP of 0.32 on the site; when the electricity tariff of $0.1/kWh was considered, the respective levelised cost of energy (LCOE) values were $0.9/kWh and $2.35/kWh respectively. The findings indicate that the initial costs for the solar thermal cooling system and the PV system were approximately $3.150M and $3M, respectively. The current value of future cash payments when discounts of 6% per year were applied to the payments for the combination of PV and air conditioning was about $9,745,000, whereas the solar thermal cooling system will not reach the breakeven point at negative $1,730,000. It is clear the absorption chiller did not display economic feasibility, whereas the value for the coupled PV and air-conditioning systems was under $0.05/kWh. In addition to the extensive maintenance needs, the reduced COP and the practicality and feasibility of the solar thermal cooling systems mean these kinds of technologies are under significant pressure to remain competitive when faced with the development of new air conditioning and PV technologies.

First and Second Law Analysis of a Flat Plate Collector Working With Nanofluids

2018 ◽  
Author(s):  
M. T. Nitsas ◽  
I. P. Koronaki ◽  
L. Prentza
Keyword(s):  
Flat Plate ◽  
Second Law Of Thermodynamics ◽  
Climatic Conditions ◽  
Working Fluid ◽  
Second Law ◽  
Inlet Temperature ◽  
Water Tank ◽  
Systems Quality ◽  
Typical Day ◽  
Flat Plate Collector

The utilization of solar energy in thermal energy systems was and always be one of the most effective alternative to conventional energy resources. Energy efficiency is widely used as one of the most important parameters in order to evaluate and compare thermal systems including solar collectors. Nevertheless, the first law of thermodynamics is not solely capable of describing the quantitative and qualitative performance of such systems and thus exergy efficiency is used so as to introduce the systems’ quality. In this work, the performance of a flat plate solar collector using water based nanofluids of different nanoparticle types as a working fluid is analyzed theoretically under the climatic conditions in Greece based on the First and Second Law of Thermodynamics. A mathematical model is built and the model equations are solved iteratively in a MATLAB code. The energy and exergy efficiencies as well as the collector losses coefficient for various parameters such as the inlet temperature, the particles concentration and type are determined. Moreover, a dynamic model is built so as to determine the performance of a flat plate collector working with nanofluids and the useful energy that can be stored in a water tank. The exergy destruction and exergy leakage are determined for a typical day in summer during which high temperatures and solar intensity values are common for the Greek climate.

Internal temperature elevation of a closed power cycle's input heat resulting from differentials in excess enthalpies of solution

2013 ◽  
Vol 26 (3) ◽  
pp. 343-346
Author(s):  
David Van Den Einde
Keyword(s):  
Second Law Of Thermodynamics ◽  
Working Fluid ◽  
Enthalpies Of Solution ◽  
Excess Enthalpies ◽  
Temperature Elevation ◽  
Internal Temperature ◽  
Power Cycle ◽  
The Difference ◽  
Gas Expansion ◽  
Cycle Efficiency

A closed power cycle using a supercritical solvent and solid solute as its working fluid is described. The difference in excess enthalpies of solution between high and low solvent densities caused by retrograde solubility in the supercritical region serves to internally elevate the temperature of a portion of the cycle's Q1 heat input before that energy affects gas expansion. The effect this internal temperature elevation has on cycle efficiency poses a dilemma for accepted definitions of the second law of thermodynamics.

Performance Analysis and Comparison Study of Transcritical Power Cycles Using CO2-Based Mixtures as Working Fluids

2016 ◽  
Author(s):  
Jiaxi Xia ◽  
Jiangfeng Wang ◽  
Pan Zhao ◽  
Dai Yiping
Keyword(s):  
Critical Temperature ◽  
Parametric Optimization ◽  
Design Parameters ◽  
Working Fluid ◽  
Comparison Study ◽  
Software Environment ◽  
Working Fluids ◽  
Power Cycles ◽  
Power Cycle ◽  
Thermodynamic Performance

CO2 in a transcritical CO2 cycle can not easily be condensed due to its low critical temperature (304.15K). In order to increase the critical temperature of working fluid, an effective method is to blend CO2 with other refrigerants to achieve a higher critical temperature. In this study, a transcritical power cycle using CO2-based mixtures which blend CO2 with other refrigerants as working fluids is investigated under heat source. Mathematical models are established to simulate the transcritical power cycle using different CO2-based mixtures under MATLAB® software environment. A parametric analysis is conducted under steady-state conditions for different CO2-based mixtures. In addition, a parametric optimization is carried out to obtain the optimal design parameters, and the comparisons of the transcritical power cycle using different CO2-based mixtures and pure CO2 are conducted. The results show that a raise in critical temperature can be achieved by using CO2-based mixtures, and CO2-based mixtures with R32 and R22 can also obtain better thermodynamic performance than pure CO2 in transcritical power cycle. What’s more, the condenser area needed by CO2-based mixture is smaller than pure CO2.

Field survey on frost damage to roof tiles under climatic conditions

2016 ◽  
Vol 34 (2) ◽  
pp. 135-149 ◽  
Author(s):  
Chiemi Iba ◽  
Ayumi Ueda ◽  
Shuichi Hokoi
Keyword(s):  
Field Survey ◽  
Winter Season ◽  
Frost Damage ◽  
Climatic Conditions ◽  
Weather Data ◽  
Measured Temperature ◽  
Content Type ◽  
Roof Tile ◽  
Deterioration Process ◽  
The Impact

Purpose – Frost damage is well-known as the main cause of roof tile deterioration. The purpose of this paper is to develop an analytical model for predicting the deterioration process under certain climatic conditions. This paper describes the results of a field survey conducted to acquire fundamental information useful to this aim. Design/methodology/approach – A field survey of roof tile damage by freezing was conducted in an old temple precinct in Kyoto, Japan. Using detailed observations and photographic recordings, the damage progress was clarified. To examine the impact of climatic conditions upon the damage characteristics, weather data and roof tile temperatures were measured and logged in the winter season. Findings – The deterioration process was observed under the climatic conditions associated with the measured temperature of the roof tiles. In particular, it was revealed that the orientation has a significant influence on increasing or decreasing the risk of frost damage. For certain distinctive forms of damage, the deterioration mechanisms were estimated from the viewpoint of the moisture flow and temperature distribution in the tile. Originality/value – This study contributes to the elucidation of the mechanism behind frost damage to roof tiles. The findings will guide the construction of a numerical model for frost damage prediction.

Studying the lubricity of new eco-friendly cutting oil formulation in metal working fluid

2018 ◽  
Vol 70 (9) ◽  
pp. 1569-1579 ◽  
Author(s):  
M.R. Noor El-Din ◽  
Marwa R. Mishrif ◽  
Satish V. Kailas ◽  
Suvin P.S. ◽  
Jagadeesh K. Mannekote
Keyword(s):  
Surface Morphology ◽  
Corrosion Inhibitor ◽  
Castor Oil ◽  
Cutting Fluid ◽  
Working Fluid ◽  
Cutting Fluids ◽  
Metal Working ◽  
Content Type ◽  
Metalworking Fluid ◽  
3D Profilometer

PurposeThis paper aims to formulate a new metal working fluid (MWF) composition including some eco-friendly emulsifiers, corrosion inhibitor, biocide, and non- edible vegetable oil (castor oil) as the base oil. To achieve this aim, five MWFs with different hydrophilic–lipophilic balance (HLB) value as 10, 9.5, 9, 8.5 and 8 were prepared to identify the optimum HLB value that gives a highly stable oil-in-water emulsion. The performance of castor oil based MWF was evaluated using tool chip tribometer and drill dynamometer. The surface morphology of steel disc and friction pin was performed using scanning electron microscope (SEM) and 3D profilometer. The results revealed that the use of the prepared cutting fluid (E1) caused the cutting force to decrease from 500 N for dry high-speed steel sample to 280N, while the same value for a commercial cutting fluid (COM) was recorded as 340 N at drilling speed and cutting feed force as 1120 rpm and 4 mm/min., respectively.Design/methodology/approachA castor oil-based metalworking fluid was prepared using nonionic surfactants. The composition of the metalworking fluid was further optimized by adding performance-enhancing additives. The performance of castor oil based MWF was analyzed using Tool chip tribometer and Drill dynamometer. The surface morphology of steel ball and a disc was done using 3D profilometer and SEM.FindingsStudies revealed that castor oil-based MWF having Monoethanolamine (MEA) as corrosion inhibitor was found to be highly stable. The drilling dynamometer and tool chip tribometer studies showed that castor oil-based MWF performance was comparable to that of commercial MWF.Research limitations/implicationsThis study aims to explore the performance of the castor oil based metalworking fluid (MWF) using tool chip tribometer and drill dynamometer.Practical implicationsThe conventional MWFs are petroleum derives and are unsustainable. Use of non-edible plant-based oils for preparing the MWF will not only be conserved environment but also add value addition to agricultural crops.Social implicationsThe social Implications is aiming to decrease the environmental impact that results from the using of mineral cutting fluids.Originality/valueThe originality of this work is to replace the mineral oil and synthetic oil based cutting fluids with more eco-friendly alternatives one. In addition, the investigation will focus on developing functional additives required for cutting fluids which are environmentally benign.

Effect of non-uniform heat source/sink on MHD boundary layer flow and melting heat transfer of Williamson nanofluid in porous medium

2019 ◽  
Vol 15 (2) ◽  
pp. 452-472 ◽  
Author(s):  
Jayarami Reddy Konda ◽  
Madhusudhana Reddy N.P. ◽  
Ramakrishna Konijeti ◽  
Abhishek Dasore
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Heat Source ◽  
Radiation Effects ◽  
Navier Stokes ◽  
Working Fluid ◽  
Content Type ◽  
Linear Ordinary Differential Equations ◽  
Uniform Heat ◽  
Source Sink

PurposeThe purpose of this paper is to examine the influence of magnetic field on Williamson nanofluid embedded in a porous medium in the presence of non-uniform heat source/sink, chemical reaction and thermal radiation effects.Design/methodology/approachThe governing physical problem is presented using the traditional Navier–Stokes theory. Consequential system of equations is transformed into a set of non-linear ordinary differential equations by means of scaling group of transformation, which are solved using the Runge–Kutta–Fehlberg method.FindingsThe working fluid is examined for several sundry parameters graphically and in a tabular form. It is noticed that with an increase in Eckert number, there is an increase in velocity and temperature along with a decrease in shear stress and heat transfer rate.Originality/valueA good agreement of the present results has been observed by comparing with the existing literature results.

Design and optimization of heating, cooling and lightening systems for a residential villa at Saman city, Iran

2019 ◽  
Vol 17 (1) ◽  
pp. 41-52 ◽  
Author(s):  
Javad Riahi Zaniani ◽  
Shahab Taghipour Ghahfarokhi ◽  
Mehdi Jahangiri ◽  
Akbar Alidadi Shamsabadi
Keyword(s):  
Energy Consumption ◽  
Light Intensity ◽  
Design Methodology ◽  
Climatic Conditions ◽  
Content Type ◽  
Design And Optimization ◽  
Simulation Results ◽  
Annual Reduction ◽  
Reduction Of Energy Consumption ◽  
Heating Loads

Purpose This paper, using energy softwares, designed of Iran and optimized a residential villa in Saman city located in Chaharmahal and Bakhtiari Province. Design/methodology/approach Having used the ideas of Climate Consultant software, the basic designing was conducted by Design Builder Software, and the cooling and heating loads and lighting tools and equipment were calculated. Then, the amount of consuming of heating, cooling and lighting load of the building was optimized through insulation of walls and ceiling, using green roof, double glazing UPVC windows, light intensity sensor and variable refrigerant flow (VRF) system. Findings Simulation results for the stated scenarios showed an annual reduction in energy consumption of 21.1, 7.9, 26.41, 27.3 and 72.3 per cent, respectively. Also, by combining all the five scenarios, an optimal state was achieved which, from the results, brought about an annual reduction of 86.9 per cent in the energy consumption. Originality/value The authors hope that the results of the current paper could be helpful for designers and engineers in reduction of energy consumption for designing a building in similar climatic conditions.

Sign in / Sign up

Export Citation Format

Share Document