Mechanical feasibility of ABS/HIPS-based multi-material structures primed by low-cost polymer printer

2019 ◽  
Vol 25 (1) ◽  
pp. 152-161 ◽  
Author(s):  
Sunpreet Singh ◽  
Narinder Singh ◽  
Munish Gupta ◽  
Chander Prakash ◽  
Rupinder Singh
Keyword(s):  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Sem Analysis ◽  
Bending Test ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Multiple Parameters ◽  
Mechanical Responses ◽  
Bending Load ◽  
Input Variables

Purpose The purpose of this paper is to fabricate acrylonitrile-butadiene-styrene (ABS)/high impact polystyrene (HIPS) based multi-material geometries using a low cost polymer printer. At the same time, efforts have been made to investigate the mechanical characteristics of the obtained prints and to perform the optimization using the Taguchi-Grey (TGRA) method. Design/methodology/approach Initially, the feedstock materials were in-house fabricated in the form of filament wires, workable with fused filament fabrication (FFF) technique, of 1.75 ± 0.1 mm diameter by using a single screw extruder. Multi-material structures were fabricated using variable parameters (such as: raster angles, layer height, fill density and solid layers) and the experimentation was conducted as per Taguchi L18 array. Mechanical responses obtained by performing tensile, impact and bending test were studied in response to input variables and ultimately optimized settings were obtained, for individual as well as multiple parameters). Scanning electron microscopy (SEM) analysis was performed to analyze the fractured surfaces. Findings The Signal/Noise (S/N) plots for the quality characteristics highlighted that selected input parameters significantly influenced the obtained values for tensile strength, impact strength and flexural strength. Micrographs of the fractured specimens showed the occurrence of brittle fracture with higher levels of perimeter, infill density and solid layers. The extent of delamination was also increased under the bending load and further increased by increasing solid layers. Practical implications The results of the study strongly advocated the utility of fabricated multi-materials structures in automotive, aerospace and other manufacturing industries. Originality/value This work represents the fabrication, testing and analysis of polymer-based multi-material structures for engineering applications.

scholarly journals Comparative study of the flexural properties of ABS, PLA and a PLA–wood composite manufactured through fused filament fabrication

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
J.A. Travieso-Rodriguez ◽  
R. Jerez-Mesa ◽  
Jordi Llumà ◽  
Giovanni Gomez-Gras ◽  
Oriol Casadesus
Keyword(s):  
Additive Manufacturing ◽  
Acrylonitrile Butadiene Styrene ◽  
Nozzle Diameter ◽  
Bending Test ◽  
Mechanical Resistance ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Layer Height ◽  
Maximum Deformation ◽  
Materials Used

Purpose The aim of this paper is to analyze the mechanical properties of acrylonitrile-butadiene-styrene (ABS) parts manufactured through fused filament fabrication and compare these results to analogous ones obtained on polylactic acid (PLA) and PLA–wood specimens to contribute for a wider understanding of the different materials used for additive manufacturing. Design/methodology/approach With that aim, an experimental based on an L27 Taguchi array was used to combine the specific parameters taken into account in the study, namely, layer height, nozzle diameter, infill density, orientation and printing velocity. All samples were subjected to a four-point bending test performed according to the ASTM D6272 standard. Findings Young’s modulus, elastic limit, maximum stress and maximum deformation of every sample were computed and subjected to an analysis of variance. Results prove that layer height and nozzle diameter are the most significant factors that affect the mechanical resistance in pieces generated through additive manufacturing and subjected to bending loads, regardless of the material. Practical implications The best results were obtained by combining a layer height of 0.1 mm and a nozzle diameter of 0.6 mm. The comparison of materials evidenced that PLA and its composite version reinforced with wood particles present more rigidity than ABS, whereas the latter can experience further deflection before break. Originality/value This study is of interest for manufacturers that want to decide which is the best material to be applied for their application, as it derives in a practical technical recommendation of the best parameters that should be selected to treat the material during the fused filament fabrication process.

Predicting strength of additively manufactured thermoplastic polymer parts produced using material extrusion

2018 ◽  
Vol 24 (2) ◽  
pp. 321-332 ◽  
Author(s):  
Joseph Bartolai ◽  
Timothy W. Simpson ◽  
Renxuan Xie
Keyword(s):  
Infrared Imaging ◽  
Acrylonitrile Butadiene Styrene ◽  
Temperature History ◽  
Interface Temperature ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Material Extrusion ◽  
Rheological Data ◽  
History Of ◽  
Butadiene Styrene

Purpose The weakest point in additively manufactured polymer parts produced by material extrusion additive manufacturing (MEAM) is the interface between adjacent layers and deposition toolpaths or “roads”. This study aims to predict the mechanical strength of parts by utilizing a novel analytical approach. Strength predictions are made using the temperature history of these interfaces, polymer rheological data, and polymer weld theory. Design/methodology/approach The approach is validated using experimental data for two common 3D-printed polymers: polycarbonate (PC) and acrylonitrile butadiene styrene (ABS). Interface temperature history data are collected in situ using infrared imaging. Rheological data of the polycarbonate and acrylonitrile butadiene styrene used to fabricate the fused filament fabrication parts in this study have been determined experimentally. Findings The strength of the interfaces has been predicted, to within 10% of experimental strength, using polymer weld theory from the literature adapted to the specific properties of the polycarbonate and acrylonitrile butadiene styrene feedstock used in this study. Originality/value This paper introduces a novel approach for predicting the strength of parts produced by MEAM based on the strength of interfaces using polymer weld theory, polymer rheology, temperature history of the interface and the forces applied to the interface. Unlike methods that require experimental strength data as a prediction input, the proposed approach is material and build orientation agnostic once fundamental parameters related to material composition have been determined.

Effect of extrusion temperature on fused filament fabrication parts orthotropic behaviour

2019 ◽  
Vol 26 (4) ◽  
pp. 639-647
Author(s):  
Michele Angelo Attolico ◽  
Caterina Casavola ◽  
Alberto Cazzato ◽  
Vincenzo Moramarco ◽  
Gilda Renna
Keyword(s):  
Mechanical Properties ◽  
Morphological Characteristics ◽  
Single Layer ◽  
Acrylonitrile Butadiene Styrene ◽  
Surface Characteristics ◽  
Tensile Tests ◽  
Extrusion Temperature ◽  
Fused Filament Fabrication ◽  
Bonding Quality ◽  
Content Type

Purpose The purpose of this paper is to verify the effects of extrusion temperature on orthotropic behaviour of the mechanical properties of parts obtained by fused filament fabrication (FFF) under quasi-static tensile loads. Design/methodology/approach Tensile tests were performed on single layer specimens fabricated in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) to evaluate the mechanical properties at different extrusion temperatures and raster orientations (0°, 45° and 90°). Furthermore, a detailed study of morphological characteristics of the single layer samples cross-section and of the bonding quality among adjacent deposited filaments was performed by scanning electron microscopy to correlate the morphology of materials with mechanical behaviour. Findings The results show that the orthotropic behaviour of FFF-printed parts tends to reduce, while the mechanical properties improved with increase in extrusion temperature. Furthermore, the increase in extrusion temperature led to an improvement in inter-raster bonding quality and in the compactness and homogeneity of the parts. Originality/value The relation between the extrusion temperature, orthotropic behaviour and morphological surface characteristics of the single layer specimen obtained by FFF has not been previously reported.

scholarly journals Increasing strength of FFF three-dimensional printed parts by influencing on temperature-related parameters of the process

2020 ◽  
Vol 26 (1) ◽  
pp. 107-121 ◽  
Author(s):  
Vladimir E. Kuznetsov ◽  
Alexey N. Solonin ◽  
Azamat Tavitov ◽  
Oleg Urzhumtsev ◽  
Anna Vakulik
Keyword(s):  
Bulk Material ◽  
Three Dimensional ◽  
Fracture Load ◽  
Bending Test ◽  
Material Strength ◽  
Thermal Imager ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Temperature Conditions ◽  
Two Factors

Purpose This paper aims to investigate how the user-controlled parameters of the fused filament fabrication three-dimensional printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the polylactic acid part. Design/methodology/approach Fracture load in a three-point bending test and calculated related stress were used as a measure. The samples were printed with the long side along the z-axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. Temperature distribution on the sample surface during printing was monitored with a thermal imager. Sample mesostructure was analyzed using scanning electron microscopy. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. Findings It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength. Originality/value The novelty of the study consists in the generalization of the outcomes. All the parameters varied can be expressed through two factors, namely, the temperature of the previous layer and the extrusion efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads).

Investigations for partial denture casting by fused deposition modelling-assisted chemical vapour smoothing

2020 ◽  
Vol 40 (5) ◽  
pp. 745-754
Author(s):  
Gurpartap Singh ◽  
Rupinder Singh ◽  
S.S. Bal
Keyword(s):  
Ph Value ◽  
Low Cost ◽  
Chemical Vapour ◽  
Dimensional Accuracy ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
View Point ◽  
Content Type ◽  
Fused Deposition ◽  
Set Up

Purpose The purpose of this study is to investigate dimensional accuracy (Δd), surface roughness (Ra) and micro hardness (HV) of partial dentures (PD) prepared with synergic combination of fused deposition modelling (FDM) assisted chemical vapour smoothing (CVS) patterns and conventional dental casting (DC) from multi-factor optimization view point. Design/methodology/approach The master pattern for PD was prepared with acrylonitrile butadiene styrene (ABS) thermoplastic on FDM set-up (one of the low cost additive manufacturing process) followed by CVS process. The final PD as functional prototypes was casted with nickel–chromium-based (Ni-Cr) alloy by varying Ni% (Z). The other input parameters were powder to water ratio P/W (X) and pH value (Y) of water used. Findings The results of this study suggest that for controlling the Δd and Ra of the PD, most important factor is X, followed by Z. For hardness of PD, the most important factor is Z. But from overall optimization viewpoint, the best settings are X-100/12, Y-10 and Z-61% (in Ni-Cr alloy). Further, based upon X-bar chart (for HV), the FDM-assisted DC process used for preparation of PD is statistically controlled. Originality/value This study highlights that PD prepared with X-100/12, Y-10 and Z-61% gives overall better results from multi-factor optimization view point. Finally, X-bar chart has been plotted to understand the statistical nature of the synergic combination of FDM, CVS and DC.

scholarly journals Effects of Filament Diameter Tolerances in Fused Filament Fabrication

2016 ◽  
Vol 2 (1) ◽  
pp. 44-47 ◽  
Author(s):  
Carolina Cardona ◽  
Abigail H Curdes ◽  
Aaron J Isaacs
Keyword(s):  
3D Printing ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Filament Fabrication ◽  
Important Indicator ◽  
Extrusion Rate ◽  
Filament Diameter ◽  
Printing Quality ◽  
3D Printers ◽  
And Control

Fused filament fabrication (FFF) is one of the most popular additive manufacturing (3D printing) technologies due to the growing availability of low-cost desktop 3D printers and the relatively low cost of the thermoplastic filament used in the 3D printing process. Commercial filament suppliers, 3D printer manufacturers, and end-users regard filament diameter tolerance as an important indicator of the 3D printing quality. Irregular filament diameter affects the flow rate during the filament extrusion, which causes poor surface quality, extruder jams, irregular gaps in-between individual extrusions, and/or excessive overlap, which eventually results in failed 3D prints. Despite the important role of the diameter consistency in the FFF process, few studies have addressed the required tolerance level to achieve highest 3D printing quality. The objective of this work is to develop the testing methods to measure the filament tolerance and control the filament fabrication process. A pellet-based extruder is utilized to fabricate acrylonitrile butadiene styrene (ABS) filament using a nozzle of 1.75 mm in diameter. Temperature and extrusion rate are controlled parameters. An optical comparator and an array of digital calipers are used to measure the filament diameter. The results demonstrate that it is possible to achieve high diameter consistency and low tolerances (0.01mm) at low extrusion temperature (180 °C) and low extrusion rate (10 in/min). 

On the build orientation effect in as-printed and as-sintered bending properties of 17-4PH alloy fabricated by metal fused filament fabrication

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Chanun Suwanpreecha ◽  
Anchalee Manonukul
Keyword(s):  
Design Methodology ◽  
Bending Strength ◽  
Low Cost ◽  
Bending Properties ◽  
Fused Filament Fabrication ◽  
Flexural Mode ◽  
Content Type ◽  
Edge Orientation ◽  
Build Orientation ◽  
Bending Strain

Purpose The purpose of this paper is to systematically investigate the influence of build orientation on the anisotropic as-printed and as-sintered bending properties of 17-4PH stainless steel fabricated by metal fused filament fabrication (MFFF). Design/methodology/approach The bending properties of 17-4PH alloy fabricated by low-cost additive manufacturing (MFFF) using three build orientations (the Flat, On-edge and Upright orientations) are examined at both as-printed and as-sintered states. Findings Unlike tensile testing where the Flat and On-edge orientations provide similar as-sintered tensile properties, the On-edge orientation produces a significantly higher bending strain with a lower bending strength than the Flat orientation. This arises from the printed layer sliding due to the Poisson's effect, which is only observed in the On-edge orientation together with the alternated layers of highly deformed and shifted voids. The bending properties show that the Upright orientation exhibits the lowest bending properties and limited plasticity due to the layer delamination. Originality/value This study is the first work to study the effect of build orientation on the flexural properties for MFFF. This work gives insight information into anisotropy in flexural mode for MFFF part design.

Experimental study of resin coating to improve the impact strength of fused filament fabrication process pieces

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Luis Lisandro López Taborda ◽  
Eduar Pérez ◽  
Daniel Quintero ◽  
José Fernando Noguera Polania ◽  
Habib Zambrano Rodriguez ◽  
...  
Keyword(s):  
Epoxy Resin ◽  
Impact Resistance ◽  
Statistical Design ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Resin Coating ◽  
Epoxy Resin Coating ◽  
Input Variables ◽  
Breaking Energy ◽  
The Impact

Purpose This study aims to evaluate the impact breaking energy of the parts manufactured by the fused filament fabrication (FFF) method. The evaluation considers the use of the epoxy resin coating, different materials and different printing orientations. Design/methodology/approach The authors developed an experimental statistical design using 54 experimental trials. The experiments’ output variable is the impact break energy of the parts manufactured by the FFF method. The input variables for the experiments consist of an epoxy resin coating (XTC-3D®, generic resin and without resin coating), different filament materials (nylon + carbon fiber, polyethylene terephthalate and polycarbonate) and different printing orientations (flat, edge and vertical) used. The authors carried out the tests following the EN ISO 179-1. Findings The use of resin coating has a significant influence on the impact energy of parts manufactured using the FFF method. The resin coating increases the impact resistance of parts processed by FFF by almost 100% of the value as compared to the parts without a resin coating. Post-processing is useful on ductile materials and increases impact breaking energy at weak print orientations. Originality/value This research opens a new opportunity to improve the mechanical properties of parts manufactured using the FFF method. The use of a resin coating reinforces the parts in weak print orientation.

scholarly journals 3D Printed End of Arm Tooling (EOAT) for Robotic Automation

Robotics ◽  
2018 ◽  
Vol 7 (3) ◽  
pp. 49
Author(s):  
Daniel Ong U Jing ◽  
Declan Devine ◽  
John Lyons
Keyword(s):  
Lean Manufacturing ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Filament Fabrication ◽  
3D Printed ◽  
Potential Weight ◽  
Materials Used ◽  
Strength And Stiffness ◽  
Flexural Tests ◽  
Robotic Automation

This research furthers the practice of designing and manufacturing End of Arm Tooling (EOAT) by utilizing a low cost additive manufacturing Fused Filament Fabrication (FFF) technique to enable tool weight saving and provision of low cost EOATs on demand, thereby facilitating zero inventory lean manufacturing. The materials used in this research for the fabrication of the EOAT parts were Acrylonitrile butadiene styrene (ABS) and nylon with infill densities of 20% and 100%. Three-point flexural tests were performed to determine the differences in strength and stiffness between varying polymers, infill ratios, and a standard metal part. Additionally, potential weight savings were identified and challenges with utilizing low cost FFF technologies are outlined. A motion of programmed trajectories was executed utilizing a standard 6-axis robot and the power consumption was evaluated. This study demonstrates the utility of using thermoplastic material with the fabrication of 3D printed parts used in EOATs.

Secondary use of ABS co-polymer recyclates for the manufacture of structural elements using the FFF technology

2018 ◽  
Vol 24 (9) ◽  
pp. 1447-1454 ◽  
Author(s):  
Piotr Czyżewski ◽  
Marek Bieliński ◽  
Dariusz Sykutera ◽  
Marcin Jurek ◽  
Marcin Gronowski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Injection Moulding ◽  
Testing Machine ◽  
Acrylonitrile Butadiene Styrene ◽  
Processing Parameters ◽  
Strength Properties ◽  
Electronic Equipment ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Hardness Tester

Purpose The aim of this paper is presenting a new application of material obtained from the acrylonitrile butadiene styrene (ABS) recycling process from electronic equipment housings. Elements of computer monitors were used to prepare re-granulate, which in turn was used to manufacture a filament for fused filament fabrication (FFF) additive manufacturing technology. Design/methodology/approach The geometry of test samples (i.e. dumbbell and bar) was obtained in accordance with the PN-EN standards. Samples made with the FFF technology were used to determine selected mechanical properties and to compare the results obtained with the properties of ABS re-granulate mould pieces made with the injection moulding technology. The GATE device manufactured by 3Novatica was used to make the prototypes with the FFF technology. Processing parameters were tested with the use of an Aflow extrusion plastometer manufactured by Zwick/Roell and other original testing facilities. Tests of mechanical properties were performed with a Z030 universal testing machine, a HIT 50P pendulum impact tester and a Z3106 hardness tester manufactured by Zwick/Roell. Findings The paper presents results of tests performed on a filament obtained from the ABS re-granulate and indicates characteristic processing properties of that material. The properties of the new secondary material were compared with the available original ABS materials that are commonly used in the additive technology of manufacturing geometrical objects. The study also presents selected results of tests of functional properties of ABS products made in the FFF technology. Originality/value The test results allowed authors to assess the possibility of a secondary application of used elements of electronic equipment housings in the FFF technology and to compare the strength properties of products obtained with similar products made with the standard injection moulding technology.

Sign in / Sign up

Export Citation Format

Share Document