Influence of laser parameters and Ti content on the surface morphology of L-PBF fabricated Titania

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Abid Ullah ◽  
HengAn Wu ◽  
Asif Ur Rehman ◽  
YinBo Zhu ◽  
Tingting Liu ◽  
...  
Keyword(s):  
Surface Morphology ◽  
Laser Beam ◽  
Surface Quality ◽  
Selective Oxidation ◽  
Laser Power ◽  
Scanning Speed ◽  
Content Type ◽  
Powder Bed ◽  
Laser Parameters

Purpose The purpose of this paper is to eliminate Part defects and enrich additive manufacturing of ceramics. Laser powder bed fusion (L-PBF) experiments were carried to investigate the effects of laser parameters and selective oxidation of Titanium (mixed with TiO2) on the microstructure, surface quality and melting state of Titania. The causes of several L-PBF parts defects were thoroughly analyzed. Design/methodology/approach Laser power and scanning speed were varied within a specific range (50–125 W and 170–200 mm/s, respectively). Furthermore, varying loads of Ti (1%, 3%, 5% and 15%) were mixed with TiO2, which was selectively oxidized with laser beam in the presence of oxygen environment. Findings Part defects such as cracks, pores and uneven grains growth were widely reduced in TiO2 L-PBF specimens. Increasing the laser power and decreasing the scanning speed shown significant improvements in the surface morphology of TiO2 ceramics. The amount of Ti material was fully melted and simultaneously changed into TiO2 by the application of the laser beam. The selective oxidation of Ti material also improved the melting condition, microstructure and surface quality of the specimens. Originality/value TiO2 ceramic specimens were produced through L-PBF process. Increasing the laser power and decreasing the scanning speed is an effective way to sufficiently melt the powders and reduce parts defects. Selective oxidation of Ti by a high power laser beam approach was used to improve the manufacturability of TiO2 specimens.

Influence of laser parameters on the surface morphology of slurry-based Al2O3 parts produced through selective laser melting

2018 ◽  
Vol 24 (2) ◽  
pp. 333-341 ◽  
Author(s):  
Kai Zhang ◽  
Tingting Liu ◽  
Wenhe Liao ◽  
Changdong Zhang ◽  
Yishuai Yan ◽  
...  
Keyword(s):  
Surface Morphology ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Laser Power ◽  
High Performance ◽  
Thermocapillary Convection ◽  
Scanning Speed ◽  
Laser Melting ◽  
Content Type ◽  
Laser Parameters

Purpose The purpose of this paper is to obtain high-performance ceramics and enrich additive manufacturing of ceramic parts. Also, a new manufacturing technique based on slurry by selective laser melting (SLM) was studied, which has some significant advantages compared to indirect selective laser sintering of ceramic powders. Design/methodology/approach To study the effect of laser parameters on the surface morphology and melting state of pure Al2O3 ceramics, laser power varied between 100 and 200 W and scan speed varied between 60 and 90 mm/s. Findings Experimental results show that Al2O3 slurry melts completely when the laser power is about 200 W and the scanning speed is 90 mm/s. Surface quality cannot be improved effectively by changing the scanning speed. However, surface quality improves when the laser power is 200∼205 W and energy density is 889∼911 J/mm3. Thermocapillary convection was observed during SLM. By changing the temperature gradient, streak convection and flowing Bénard cells were obtained during SLM of Al2O3 slurry. Originality/value It is feasible to produce slurry ceramic parts without binders through SLM. Increasing the laser power is the most effective way to fully melt the ceramics. Complex thermocapillary convection was observed during this new process; it may be used to produce crystals.

The mechanism of process parameters influencing the AlSi10Mg side surface quality fabricated via laser powder bed fusion

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Shimin Dai ◽  
Hailong Liao ◽  
Haihong Zhu ◽  
Xiaoyan Zeng
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Process Parameters ◽  
Laser Power ◽  
Side Surface ◽  
Laser Powder Bed Fusion ◽  
Scanning Velocity ◽  
Content Type ◽  
Powder Bed

Purpose For the laser powder bed fusion (L-PBF) technology, the side surface quality is essentially important for industrial applicated parts, such as the inner flow parts. Contour is generally adopted at the parts’ outline to enhance the side surface quality. However, the side surface roughness (Ra) is still larger than 10 microns even with contour in previous studies. The purpose of this paper is to study the influence of contour process parameters, laser power and scanning velocity on the side surface quality of the AlSi10Mg sample. Design/methodology/approach Using L-PBF technology to manufacture AlSi10Mg samples under different contour process parameters, use a laser confocal microscope to capture the surface information of the samples, and obtain the surface roughness Ra and the maximum surface height Rz of each sample after analysis and processing. Findings The results show that the side surface roughness decreases with the increase of the laser power at the fixed scanning velocity of 1,000 mm/s, the side surface roughness Ra stays within the error range as the contour velocity increases. It is found that the Ra increases with the scanning velocity increasing and the greater the laser power with the greater Ra increases when the laser power of contour process parameters is 300 W, 350 W and 400 W. The Rz maintain growth with the contour scanning velocity increasing at constant laser power. The continuous uniform contour covers the pores in the molten pool of the sample edge and thus increase the density of the sample. Two mechanisms named “Active adhesion” and “Passive adhesion” cause sticky powder. Originality/value Formation of a uniform and even contour track is key to obtain the good side surface quality. The side surface quality is determined by the uniformity and stability of the contour track when the layer thickness is fixed. These research results can provide helpful guidance to improve the surface quality of L-PBF manufactured parts.

Optimization of built-part distortion in laser powder bed fusion processing of Inconel 718

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
You-Cheng Chang ◽  
Hong-Chuong Tran ◽  
Yu-Lung Lo
Keyword(s):  
Cooling Rate ◽  
Cantilever Beam ◽  
Laser Power ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Laser Powder Bed Fusion ◽  
Simulation Framework ◽  
Content Type ◽  
Powder Bed ◽  
Simulation Results

Purpose Laser powder bed fusion (LPBF) provides the means to produce unique components with almost no restriction on geometry in an extremely short time. However, the high-temperature gradient and high cooling rate produced during the fabrication process result in residual stress, which may prompt part warpage, cracks or even baseplate separation. Accordingly, an appropriate selection of the LPBF processing parameters is essential to ensure the quality of the built part. This study, thus, aims to develop an integrated simulation framework consisting of a single-track heat transfer model and a modified inherent shrinkage method model for predicting the curvature of an Inconel 718 cantilever beam produced using the LPBF process. Design/methodology/approach The simulation results for the curvature of the cantilever beam are calibrated via a comparison with the experimental observations. It is shown that the calibration factor required to drive the simulation results toward the experimental measurements has the same value for all settings of the laser power and scanning speed. Representative combinations of the laser power and scanning speed are, thus, chosen using the circle packing design method and supplied as inputs to the validated simulation framework to predict the corresponding cantilever beam curvature and density. The simulation results are then used to train artificial neural network models to predict the curvature and solid cooling rate of the cantilever beam for any combination of the laser power and scanning speed within the input design space. The resulting processing maps are screened in accordance with three quality criteria, namely, the part density, the radius of curvature and the solid cooling rate, to determine the optimal processing parameters for the LPBF process. Findings It is shown that the parameters lying within the optimal region of the processing map reduce the curvature of the cantilever beam by 17.9% and improve the density by as much as 99.97%. Originality/value The present study proposes a computational framework, which could find the parameters that not only yield the lowest distortion but also produce fully dense components in the LPBF process.

scholarly journals Effect of Process Parameters and Layer Thickness on the Quality and Performance of Ti-6Al-4V Fabricated by Selective Laser Melting

Coatings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1323
Author(s):  
Yanlong Jing ◽  
Peng Wang ◽  
Xiaoling Yan
Keyword(s):  
Surface Quality ◽  
Selective Laser Melting ◽  
Exposure Time ◽  
Process Parameters ◽  
Laser Power ◽  
Single Track ◽  
Laser Melting ◽  
Powder Bed ◽  
Point Distance

To improve the quality of thick powder bed and realize the matching of thick powder bed and thin powder bed in the later stage, the influence of process parameters for the single-track, multi-layer fabrication, relative density, surface quality, defect, remelting, and boundary optimization performance of different layer thicknesses of Ti-6Al-4V fabricated by selective laser melting were investigated. It is more conducive to the stable forming of single-track when the point distance is half the diameter of the laser beam, and the exposure time is appropriately extended. The thin powder bed needs the corresponding point distance and exposure time under the laser power of 280–380 W to obtain high-density specimens. The thick powder bed needs to be able to ensure the formation of high-quality specimens under the smaller point distance and longer exposure time under higher laser power of 380 W. Both thick powder bed and thin powder bed will cause un-melted defects between molten pools, spheroidization defects caused by splashing, and microporous defects. The remelting process can significantly improve the surface quality of the formed specimen, but the surface quality of the thick powder bed is worse than that of the thin powder bed. The boundary quality of thick powder bed is worse than that of thin powder bed, and the boundary shape has a greater influence on the quality of the SLM forming boundary. Different strategies should be adopted to form the boundary of different shapes. Increasing the boundary count and increasing the laser power are more conducive to the improvement of boundary quality.

scholarly journals Face Grinding Surface Quality of High Volume Fraction SiCp/Al Composite Materials

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Xu Zhao ◽  
Yadong Gong ◽  
Guiqiang Liang ◽  
Ming Cai ◽  
Bing Han
Keyword(s):  
Friction Coefficient ◽  
Surface Morphology ◽  
Surface Quality ◽  
Volume Fraction ◽  
High Volume ◽  
Spindle Speed ◽  
High Volume Fraction ◽  
Machining Parameters ◽  
Al Composite

AbstractThe existing research on SiCp/Al composite machining mainly focuses on the machining parameters or surface morphology. However, the surface quality of SiCp/Al composites with a high volume fraction has not been extensively studied. In this study, 32 SiCp/Al specimens with a high volume fraction were prepared and their machining parameters measured. The surface quality of the specimens was then tested and the effect of the grinding parameters on the surface quality was analyzed. The grinding quality of the composite specimens was comprehensively analyzed taking the grinding force, friction coefficient, and roughness parameters as the evaluation standards. The best grinding parameters were obtained by analyzing the surface morphology. The results show that, a higher spindle speed should be chosen to obtain a better surface quality. The final surface quality is related to the friction coefficient, surface roughness, and fragmentation degree as well as the quantity and distribution of the defects. Lower feeding amount, lower grinding depth and appropriately higher spindle speed should be chosen to obtain better surface quality. Lower feeding amount, higher grinding depth and spindle speed should be chosen to balance grind efficiently and surface quality. This study proposes a systematic evaluation method, which can be used to guide the machining of SiCp/Al composites with a high volume fraction.

Improvement of Build Speed and Quality of H13 Tool Steel Processed by Laser-Beam Powder Bed Fusion with a High-Power Laser

2021 ◽  
Vol 68 (10) ◽  
pp. 415-421
Author(s):  
Takashi MIZOGUCHI ◽  
Takaya NAGAHAMA ◽  
Makoto TANO ◽  
Shigeru MATSUNAGA ◽  
Takayuki YOSHIMI ◽  
...  
Keyword(s):  
Laser Beam ◽  
Tool Steel ◽  
High Power ◽  
Powder Bed Fusion ◽  
High Power Laser ◽  
Power Laser ◽  
Powder Bed ◽  
H13 Tool Steel

Track evolution and surface characteristics of selective laser melting Ti6Al4V

2018 ◽  
Vol 24 (9) ◽  
pp. 1554-1562 ◽  
Author(s):  
Luo Zhang ◽  
Haihong Zhu ◽  
Jiahe Liu ◽  
Xiaoyan Zeng
Keyword(s):  
Surface Morphology ◽  
Selective Laser Melting ◽  
Surface Characteristics ◽  
Scanning Speed ◽  
Bulk Sample ◽  
Three Dimension ◽  
Single Track ◽  
Heat Accumulation ◽  
Laser Melting ◽  
Content Type

Purpose The purpose of this paper is to investigate the track evolution and surface characteristics of selective laser melting Ti6Al4V. Design/methodology/approach In the present paper, Ti6Al4V single-track, multi-track and bulk sample were formed at different scanning speed by selective laser melting (SLM). Then, the surface morphology, three-dimension profile and surface roughness were evaluated. The width of the single and multi-track was measured and compared. Findings The results showed that the heat accumulation played a great role on the evolution of tracks and surface characteristics from single-track to multi-track and to bulk. The surface morphology of the subsequent tracks became more regular when the single-track was irregular at the same high scanning speed. The width of last track Wn was always larger than that of the first track W1. The Ra of the top of the bulk increased with the increase of the scanning speed, this trend was as same as the Ra of the single-track, but the trend of Ra of the side was opposite. Originality/value The effect of heat accumulation on the track evolution and surface characteristics is obtained. The results can help to derive a smooth surface with a regular and continuous track in SLM.

scholarly journals Effect of Laser Parameters on Sequential Laser Beam Micromachining and Micro Electro-Discharge Machining

2021 ◽  
Author(s):  
Mir Akmam Noor Rashid ◽  
Tanveer Saleh ◽  
Wazed Ibne Noor ◽  
Mohamed Sultan Mohamed Ali
Keyword(s):  
Laser Beam ◽  
Laser Power ◽  
Short Circuit ◽  
Scanning Speed ◽  
Hole Drilling ◽  
Machining Time ◽  
Research Attention ◽  
Pilot Hole ◽  
Electro Discharge Machining ◽  
Input Parameters

Abstract Laser beam micromachining (LBMM) and micro electro-discharge machining (µEDM) based sequential micromachining technique, LBMM-µEDM has drawn significant research attention to utilizing the advantages of both methods, i.e. LBMM and µEDM. In this process, a pilot hole is machined by the LBMM and subsequently finishing operation of the hole is carried out by the µEDM. This paper presents an experimental investigation on the stainless steel (type SS304) to observe the effects of laser input parameters (namely laser power, scanning speed, and pulse frequency) on the performance of the finishing technique that is the µEDM in this case. The scope of the work is limited to 1-D machining, i.e. drilling micro holes. It was found that laser input parameters mainly scanning speed and power influenced the output performance of µEDM significantly. Our study suggests that if an increased scanning speed at a lower laser power is used for the pilot hole drilling by the LBMM process, it could result in significantly slower µEDM machining time. On the contrary, if the higher laser power is used with even the highest scanning speed for the pilot hole drilling, then µEDM processing time was faster than the previous case. Similarly, µEDM time was also quicker for LBMMed pilot holes machined at low laser power and slow scanning speed. Our study confirms that LBMM-µEDM based sequential machining technique reduces the machining time, tool wear and instability (in terms of short circuit count) by a margin of 2.5 x, 9 x and 40 x respectively in contrast to the pure µEDM process without compromising the quality of the holes.

Experimental study on the accuracy and surface quality of printed versus machined holes in PEI Ultem 9085 FDM specimens

2021 ◽  
Vol 27 (11) ◽  
pp. 1-12
Author(s):  
Giovanni Gómez-Gras ◽  
Marco A. Pérez ◽  
Jorge Fábregas-Moreno ◽  
Guillermo Reyes-Pozo
Keyword(s):  
Surface Quality ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
Technological Parameters ◽  
Content Type ◽  
Fused Deposition ◽  
Comparison Of The Results ◽  
Through Hole

Purpose This paper aims to investigate the quality of printed surfaces and manufacturing tolerances by comparing the cylindrical cavities machined in parts obtained by fused deposition modeling (FDM) with the holes manufactured during the printing process itself. The comparison focuses on the results of roughness and tolerances, intending to obtain practical references when making assemblies. Design/methodology/approach The experimental approach focuses on the comparison of the results of roughness and tolerances of two manufacturing strategies: geometric volumes with a through-hole and the through-hole machined in volumes that were initially printed without the hole. Throughout the study, both alternates are explained to make appropriate recommendations. Findings The study shows the best combinations of technological parameters, both machining and three-dimensional printing, which have been decisive for obtaining successful results. These conclusive results allow enunciating recommendations for use in the industrial environment. Originality/value This paper fulfills an identified need to study the dimensional accuracy of the geometries obtained by additive manufacturing, as no experimental evidence has been found of studies that directly address the problem of the FDM-printed part with geometric and dimensional tolerances and desirable surface quality for assembly.

Sign in / Sign up

Export Citation Format

Share Document