Combined First and Second-Law Analysis of Gas Turbine Cogeneration System With Inlet Air Cooling and Evaporative Aftercooling of the Compressor Discharge

2007 ◽  
Vol 129 (4) ◽  
pp. 1004-1011 ◽  
Author(s):  
A. Khaliq ◽  
K. Choudhary
Keyword(s):  
Relative Humidity ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Second Law ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Exergy Destruction ◽  
Turbine Inlet Temperature ◽  
Ambient Relative Humidity ◽  
Turbine Inlet

A conceptual gas turbine based cogeneration cycle with compressor inlet air cooling and evaporative aftercooling of the compressor discharge is proposed to increase the cycle performance significantly and render it practically insensitive to seasonal temperature fluctuations. Combined first and second-law approach is applied for a cogeneration system having intercooled reheat regeneration in a gas turbine as well as inlet air cooling and evaporative aftercooling of the compressor discharge. Computational analysis is performed to investigate the effects of the overall pressure ratio rp, turbine inlet temperature (TIT), and ambient relative humidity φ on the exergy destruction in each component, first-law efficiency, power-to-heat ratio, and second-law efficiency of the cycle. Thermodynamic analysis indicates that exergy destruction in various components of the cogeneration cycle is significantly affected by overall pressure ratio and turbine inlet temperature, and not at all affected by the ambient relative humidity. It also indicates that the maximum exergy is destroyed during the combustion process, which represents over 60% of the total exergy destruction in the overall system. The first-law efficiency, power-to-heat ratio, and second-law efficiency of the cycle significantly vary with the change in the overall pressure ratio and turbine inlet temperature, but the change in relative humidity shows small variations in these parameters. Results clearly show that performance evaluation based on first-law analysis alone is not adequate, and hence, more meaningful evaluation must include second-law analysis. Decision makers should find the methodology contained in this paper useful in the comparison and selection of advanced combined heat and power systems.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Performance analysis of an air humidifier integrated gas turbine with film air cooling of turbine blade

2013 ◽  
Vol 24 (4) ◽  
pp. 71-81 ◽  
Author(s):  
Alok K. Mahapatra ◽  
Sanjay Sanjay
Keyword(s):  
Relative Humidity ◽  
Ambient Temperature ◽  
Pressure Ratio ◽  
Temperature Drop ◽  
Inlet Temperature ◽  
Specific Work ◽  
Blade Cooling ◽  
Ambient Relative Humidity ◽  
Turbine Inlet ◽  
Compressor Pressure Ratio

A computational analysis to investigate the effects of compressor pressure ratio, turbine inlet temperature, ambient relative humidity and ambient temperature on the performance parameters of an air cooled gas turbine cycle with evaporative cooling of inlet air has been presented. The blade cooling method selected is film cooling. The analysis indicates that the mass of coolant required for blade cooling is reduced with increase in temperature drop across the humidifier. Both decrease in ambient temperature and ambient relative humidity results in an increase in plant efficiency and plant specific work. The highest efficiency is obtained at a turbine inlet temperature of 1500 K for all range of ambient relative humidity and ambient temperature, beyond which it decreases. The compressor pressure ratio corresponding to the maximum plant specific work, however, varies with both ambient relative humidity and ambient temperature. The increase in specific work due to drop in ambient relative humidity is more pronounced at higher pressure ratios. Similarly, the increase in efficiency due to ambient temperature drop is prominent at higher turbine inlet temperatures. Finally, a design nomograph is presented to select the design parameters corresponding to best efficiency and specific work.

A 2000-HP Military Vehicle Gas Turbine: A Study of Significant Thermodynamic and Mechanical Parameters

1968 ◽  
Author(s):  
A. F. Carter
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Overall Design ◽  
Blade Cooling ◽  
Turbine Inlet ◽  
Military Vehicle ◽  
Compressor Pressure Ratio ◽  
Selection Of

During a study of possible gas turbine cycles for a 2000-hp unit for tank propulsion, it has been established that the level of achievable specific fuel consumption (sfc) is principally determined by the combustor inlet temperature. If a regenerative cycle is selected, a particular value of combustor inlet temperature (and hence sfc) can be produced by an extremely large number of combinations of compressor pressure ratio, turbine inlet temperature, and heat exchanger effectiveness. This paper outlines the overall design considerations which led to the selection of a relatively low pressure ratio engine in which the turbine inlet temperature was sufficiently low that blade cooling was not necessary.

scholarly journals Exergy Efficiency Optimization for Gas Turbine Based Cogeneration Systems

2013 ◽  
Author(s):  
Ana C. Ferreira ◽  
Senhorinha F. Teixeira ◽  
José C. Teixeira ◽  
Manuel L. Nunes ◽  
Luís B. Martins
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Exergy Analysis ◽  
Exergy Efficiency ◽  
Plant Performance ◽  
System Component ◽  
Inlet Temperature ◽  
Exergy Destruction ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

Energy degradation can be calculated by the quantification of entropy and loss of work and is a common approach in power plant performance analysis. Information about the location, amount and sources of system deficiencies are determined by the exergy analysis, which quantifies the exergy destruction. Micro-gas turbines are prime movers that are ideally suited for cogeneration applications due to their flexibility in providing stable and reliable power. This paper presents an exergy analysis by means of a numerical simulation of a regenerative micro-gas turbine for cogeneration applications. The main objective is to study the best configuration of each system component, considering the minimization of the system irreversibilities. Each component of the system was evaluated considering the quantitative exergy balance. Subsequently the optimization procedure was applied to the mathematical model that describes the full system. The rate of irreversibility, efficiency and flaws are highlighted for each system component and for the whole system. The effect of turbine inlet temperature change on plant exergy destruction was also evaluated. The results disclose that considerable exergy destruction occurs in the combustion chamber. Also, it was revealed that the exergy efficiency is expressively dependent on the changes of the turbine inlet temperature and increases with the latter.

Comparative Thermodynamic Analysis of Gas Turbine Systems with Turbine Blade Film Cooling

2012 ◽  
Vol 505 ◽  
pp. 539-543
Author(s):  
Kyoung Hoon Kim ◽  
Kyoung Jin Kim ◽  
Chul Ho Han
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Thermodynamic Analysis ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Blade Cooling ◽  
Turbine Inlet

Since the gas turbine systems require active cooling to maintain high operating temperature while avoiding a reduction in the system operating life, turbine blade cooling is very important and essential but it may cause the performance losses in gas turbine. This paper deals with the comparative thermodynamic analysis of gas turbine system with and without regeneration by using the recently developed blade-cooling model when the turbine blades are cooled by the method of film cooling. Special attention is paid to investigating the effects of system parameters such as pressure ratio and turbine inlet temperature on the thermodynamic performance of the systems. In both systems the thermal efficiency increases with turbine inlet temperature, but its effect is less sensitive in simpler system

Exergy Analysis of an Indirectly-Fired Combined Cycle Power Generation System

2008 ◽  
Author(s):  
Kin F. Chui ◽  
Nirmal V. Gnanapragasam ◽  
Bale V. Reddy ◽  
Ramesh C. Prasad
Keyword(s):  
Natural Gas ◽  
Circulating Fluidized Bed ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Exergy Destruction ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Firing Mode ◽  
Fluidized Bed Combustor

A natural gas fired combined cycle power plant with indirectly-fired heating for additional work output is investigated in the current work. The mass flow rate of coal for the indirect firing mode in circulating fluidized bed combustor is estimated based on fixed natural gas input to the topping combustor. The effects of pressure ratio, gas turbine inlet temperature, inlet temperature to the topping combustor on the exergetic performance of the combined cycle configuration are analysed. The use of coal in indirect-firing mode reduces with increase in turbine inlet temperature due to increase in the use of natural gas. The exergetic efficiency increases with pressure ratio up to the optimum pressure and it also increase with gas turbine inlet temperature. The exergy destruction is highest for the circulating fluidized bed combustor (CFBC) followed by the topping combustor. The analyses show that the indirectly fired mode of the combined cycle offers better performance but with higher exergy destruction and the opportunity for additional net work output by using solid fuels (coal in this case) in existing natural gas based power plant is realized.

scholarly journals Exergy, economic and environmental (3E) analysis of a gas turbine power plant and optimization by MOPSO algorithm

2018 ◽  
Vol 22 (6 Part A) ◽  
pp. 2641-2651 ◽  
Author(s):  
Moein Shamoushaki ◽  
Mehdi Ehyaei
Keyword(s):  
Gas Turbine ◽  
Co2 Emission ◽  
Emission Rate ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Total Cost ◽  
Cost Rate ◽  
Turbine Inlet ◽  
Compressor Pressure Ratio

In this paper, exergy, exergoeconomic, and exergoenvironmental analysis of a gas turbine cycle and its optimization has been carried out by MOPSO algorithm. Three objective functions, namely, total cost rate, exergy efficiency of cycle, and CO2 emission rate have been considered. The design variables considered are: compressor pressure ratio, combustion chamber inlet temperature, gas turbine inlet temperature, compressor, and gas turbine isentropic efficiency. The impact of change in gas turbine inlet temperature and compressor pressure ratio on CO2 emission rate as well as impact of changes in gas turbine inlet temperature on exergy efficiency of the cycle has been investigated in different compressor pressure ratios. The results showed that with increase in compressor pressure ratio and gas turbine inlet temperature, CO2 emission rate decreases, that is this reduction is carried out with a steeper slope at lower pressure compressor ratio and gas turbine inlet temperature. The results showed that exergy efficiency of the cycle increases with increase in gas turbine inlet temperature and compressor pressure ratio. The sensitivity analysis of fuel cost changes was performed on objective functions. The results showed that at higher exergy efficiencies total cost rate is greater, and sensitivity of fuel cost optimum solutions is greater than Pareto curve with lower total cost rate. Also, the results showed that sensitivity of changes in fuel cost rate per unit of energy on total cost rate is greater than the rate of CO2 emission.

Analysis of Integrated Cooling Systems for Gas Turbine Power Plants

2017 ◽  
Author(s):  
Waleed El-Damaty ◽  
Mohamed Gadalla
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Turbine Inlet Temperature ◽  
Current Increase ◽  
Turbine Inlet ◽  
Compact Size

With the current increase in electricity consumption and energy demand, most of the research focus is shifted towards the means of increasing the power plants efficiency in order to produce more electricity by using as less fuel as possible. Gas turbine power plants specifically have been under the study in the recent years due to its feasibility, low capital cost, simple design, compact size and higher efficiency compared to steam turbine power plants. There are a lot of operating conditions that affect the performance of the gas turbine which includes the inlet air climatic conditions, mass flow rate and the turbine inlet temperature. Many improvements and enhancements became applicable through the advancement in the material and cooling technologies. Cooling techniques could be used to cool the inlet air entering the compressor by utilizing evaporative coolers and mechanical chillers, and to cool the turbine blades in order to avoid a decline in the life of turbine blades due to unwanted exposure to thermal stresses and oxidation. Internal convection cooling, film cooling and transpiration cooling are the three main techniques that can be used in the process of turbine blades cooling. The main objective of this proposal is to improve the durability and performance of gas turbine power plants by proposing the usage of integrated system of solid desiccant with Maisotsenko cooler in the turbine blade cooling and inlet air cooling processes. Four configurations were presented and the results were an increase in the efficiency of the gas turbine cycle for all the cases specially the two stage Maisotsenko desiccant cooling system where the efficiency increased from 33.33% to 34.17% as well as maintaining the turbine inlet temperature at a desired level of 1500°K.

Performance Analysis of a 50KW Turbogenerator Gas Turbine Engine

1998 ◽  
Author(s):  
S. Y. Kim ◽  
M. R. Park ◽  
S. Y. Cho
Keyword(s):  
Performance Analysis ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Hybrid Vehicle ◽  
Gas Turbine Engine ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Design Point ◽  
Turbine Inlet

This paper describes on/off design performance of a 50KW turbogenerator gas turbine engine for hybrid vehicle application. For optimum design point selection, a relevant pa4rameter study is carried out. The turbogenerator gas turbine engine for a hybrid vehicle is expected to be designed for maximum fuel economy, ultra low emissions, and very low cost. A compressor, combustor, turbine, and a permanent-magnet generator will be mounted on a single high speed (80,000 rpm) shaft that will be supported on air bearings. As the generator is built into the shaft, gearbox and other moving parts become unnecessary and thus will increase the system’s reliability and reduce the manufacturing cost. The engine has a radial compressor and turbine with design point pressure ratio of 4.0. This pressure ratio was set based on calculation of specific fuel consumption and specific power variation with pressure ratio. For the turbine inlet temperature, a rather conservative value of 1100K was selected. Designed mass flow rate was 0.5 kg/sec. Parametric study of the cycle indicates that specific work and efficiency increase at a given pressure ratio and turbine inlet temperature. Off design analysis shows that the gas turbine system reaches self operating condition at about N/NDP = 0.48. Bleeding air for a turbine stator cooling is omitted considering the low TIT in the present engine and to enable the simple geometric configuration for manufacturing purpose. Various engine performance simulations including ambient temperature influence, surging at part load condition; transient analysis were performed to secure the optimum engine operating characteristics. Surge margin throughout the performance analysis were maintained to be over 50% approximately. Present analysis will be compared with performance test result which is scheduled at the end of 1998.

A Comparative Study on the Options in Combining Solid Oxide Fuel Cell With Gas Turbine

2015 ◽  
Author(s):  
Ji Hye Yi ◽  
Ju Hwan Choi ◽  
Tong Seop Kim
Keyword(s):  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Solid Oxide ◽  
Inlet Temperature ◽  
Oxide Fuel ◽  
System Efficiency ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

Various options in combining a solid oxide fuel cell (SOFC) with a gas turbine (GT) were compared in this study. The combination of an SOFC with either a simple gas turbine or a gas/steam turbine combined cycle was investigated. For each combined system, the effect of using a recuperative heat exchanger was examined. The design parameters of a state-of-the-art gas turbine for central power stations were used. The GT modeling included modulation of turbine coolant flow depending on turbine working conditions. An SOFC temperature of 900°C was used. Given a currently available reference voltage, pressure-dependent SOFC cell voltage was used. The analysis was divided into two parts. In the first part, the turbine inlet temperature of the reference gas turbine was given and the influence of pressure ratio was analyzed. In the second part, the influence of varying turbine inlet temperature was analyzed to search for optimal design conditions. The results showed that the SOFC/GTCC systems would provide considerably higher efficiencies than the SOFC/GT systems. The optimal pressure ratio in terms of system efficiency is over 30 for non-recuperated systems but is around 10 for recuperated systems. Reducing the extra fuel to the gas turbine combustor improves system efficiency, especially in the SOFC/GT systems. With zero extra fuel, efficiencies of all of the four systems exceed 70%, the highest of which is obtained by the recuperated SOFC/GTCC layout.

Sign in / Sign up

Export Citation Format

Share Document