Effects of Synchronous Vibration of Bearing on Stability of Externally Pressurized Air Journal Bearings

1999 ◽  
Vol 121 (4) ◽  
pp. 830-835 ◽  
Author(s):  
Jeong-Bae Lee ◽  
Kyung-Woong Kim
Keyword(s):  
Steady State ◽  
Phase Difference ◽  
High Speed ◽  
Control Algorithm ◽  
Journal Bearing ◽  
Stability Limit ◽  
Air Bearing ◽  
Synchronous Motion ◽  
Maximum Stability ◽  
The Stability

An active control of bearing is proposed as a new method to improve the stability characteristics of the externally pressurized air journal bearing and the results of numerical investigations of the stability characteristics of the actively controlled air journal bearing are presented. The synchronous control, where the bearing center whirls with the same frequency as the journal center with respect to the position in the steady state, is proposed as a control algorithm of the active air bearing. The step jump method is used to calculate the locus of the journal center which whirls or vibrates relative to the whirling bearing. The stability characteristics of the high speed rotor supported by actively controlled bearing system for zero steady-state eccentricity are investigated for various phase difference between the bearing and journal. It is shown that the stability of the air bearing can be greatly increased by the controlled synchronous motion of the bearing, and there is an optimum phase difference, which gives the maximum stability limit of the system.

Impedance Control of Gyroscopic Power Generator

2011 ◽  
Author(s):  
Tomoyuki Takahashi ◽  
Jun Iwasaki ◽  
Hiroshi Hosaka
Keyword(s):  
Steady State ◽  
Phase Difference ◽  
High Speed ◽  
Control Method ◽  
Impedance Control ◽  
Low Frequency ◽  
Power Generator ◽  
Communication Devices ◽  
High Speed Rotation ◽  
The Stability

The gyroscopic power generator produces a high-speed rotation of magnets from low-frequency vibrations and supplies electric power to information and communication devices that use human vibrations in daily life. In this paper, in order to increase the stability and the output power of the generator, a simple equation that indicates the steady state approximate solution of the phase difference is derived. From the derived solution, a control method for the steady state is verified by the simulations. In order to maintain the stability and high power generation for variable input vibrations, the impedance control method using the phase difference is developed and verified experimentally.

Analysis and comparison of steady-state performance characteristics of two-axial groove and multilobe hydrodynamic bearings lubricated with non-Newtonian fluids

2018 ◽  
Vol 232 (12) ◽  
pp. 1581-1596 ◽  
Author(s):  
Bhrigu Jyoti Das ◽  
Lintu Roy
Keyword(s):  
Steady State ◽  
High Speed ◽  
Journal Bearing ◽  
Maximum Flow ◽  
Maximum Load ◽  
Performance Characteristics ◽  
Flow Coefficient ◽  
Rotating Speed ◽  
The Stability ◽  
Steady State Performance

Rotating machines are one of the most important and widely used machineries in the modern engineering world. They are also the required to run at high rotating speed. The plain journal bearing is mostly replaced by some other bearing, as it does not suit the stability requirement of high-speed machines and precision machine tools. In order to improve the stability of a circular bearing, many researchers tried to change its geometrical configuration. In view of this, an attempt has been made in the present work to study the performance characteristics of four different bearing configurations using non-Newtonian lubricant and comparison of the results has been made with plain journal bearing. To calculate the steady-state performance characteristics, nondimensional form of the Reynolds equation using non-Newtonian lubricant has been written and solved for the steady-state nondimensional pressure distribution in a finite grid using finite difference method with successive over-relaxation technique satisfying appropriate boundary condition. From the study, it can be concluded that three-lobe bearing have maximum load-carrying capacity and minimum friction variable, whereas two-lobe bearing have maximum flow coefficient.

Effect of Current Waveform on Metal Transfer in Controlled Short Circuiting Gas Metal Arc Welding

2013 ◽  
Vol 718-720 ◽  
pp. 202-208 ◽  
Author(s):  
Mao Ai Chen ◽  
Yuan Ning Jiang ◽  
Chuan Song Wu
Keyword(s):  
Transfer Process ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Current ◽  
Metal Transfer ◽  
Arc Voltage ◽  
Metal Arc Welding ◽  
Maximum Stability ◽  
The Stability ◽  
Welding Inverter

With high-speed welding inverter and precisely controlling the welding current with arc-bridge state, advanced pulse current waveforms can be produced to optimize the transfer characteristics of short circuiting transfer welding. In this paper, the images of droplet/wire, and the transient data of welding current and arc voltage were simultaneously recorded to study the influence of peak arcing current, background arcing current and tail-out time on the stability of short circuiting transfer process. It was found that maximum short circuiting transfer stability is reached under specific welding conditions. Any deviation from these conditions will cause abnormal rises in arc voltage indicating instantaneous arc extinguishing and greater spatter. Optimal welding conditions were obtained to achieve the maximum stability of short circuiting metal transfer process.

A Variable Viscosity Approach for the Analysis of Steady State and Dynamic Characteristics of Two-Lobe Journal Bearing With TiO2 Based Nanolubricant

2017 ◽  
Author(s):  
Ashutosh Kumar ◽  
Sashindra Kumar Kakoty
Keyword(s):  
Steady State ◽  
Dynamic Characteristics ◽  
Journal Bearing ◽  
Volume Fraction ◽  
Variable Viscosity ◽  
Flow Coefficient ◽  
Viscosity Model ◽  
Nano Lubricant ◽  
The Stability ◽  
Stiffness And Damping

Steady-state and dynamic characteristics of two-lobe journal bearing, operating on TiO2 based Nano-lubricant has been obtained. The effective viscosity is obtained by using Krieger-Dougherty viscosity model for a given volume fraction of nanoparticle in the base fluid. Various bearing performance characteristics are then obtained by solving modified Reynolds equation for variable viscosity model and couple stress model. The stiffness and damping coefficients are also determined for various values of the volume fraction of the nanoparticle in the nanofluid. Results reveal that load carrying capacity and flow coefficient increase whereas friction variable decreases without affecting the stability condition of two-lobe journal bearing operating on TiO2 based nanolubricant. On the other hand attitude angle and dynamic coefficients remains constant for all the values of volume fraction of nanoparticle.

Criteria for the Stability Limit Prediction of High Speed Centrifugal Compressors With Vaneless Diffuser: Part I — Flow Structure Analysis

2020 ◽  
Author(s):  
Carlo Cravero ◽  
Davide Marsano
Keyword(s):  
Rotational Speed ◽  
High Speed ◽  
Stability Limit ◽  
Vaneless Diffuser ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
High Rotational Speed ◽  
Lower Accuracy ◽  
The Stability ◽  
Computational Resources

Abstract High-speed centrifugal compressor requirements include a wide operating range between choking and stall especially for turbocharging applications. The prediction of the stability limit at different speeds is still challenging. In literature, several studies have been published on the phenomena that trigger the compressor instability. However, a comprehensive analysis of criteria that can be used in the first steps of centrifugal compressors design to predict the stability limit is still missing. In previous work the authors have already presented a criterion, so called “Stability Parameter”, to predict the surge line of centrifugal compressors based on a simplified CFD approach that does not require excessive computational resources and that can be efficiently used in the preliminary design phases. The above methodology has demonstrated its accuracy for centrifugal compressors with vaned diffuser, but a lower accuracy has been detected for vaneless diffusers. Before proceeding to identify additional criteria focused on compressors with vaneless diffuser, an in-depth fluid dynamics analysis has been necessary. This analysis has been also carried out through fully 3D unsteady simulations to allow identifying the real phenomena linked to the trigger of the instability of centrifugal compressors. It has been found how these phenomena are strongly related to the rotational speed, in particular have been shown the key role of the volute at high rotational speed.

scholarly journals Simulation analysis of efficiency and stability for vehicle’s ABS control on combined steering and braking maneuvers

2019 ◽  
Vol 272 ◽  
pp. 01024 ◽  
Author(s):  
Feng YU ◽  
Jun XIE
Keyword(s):  
High Speed ◽  
Control Algorithm ◽  
Degrees Of Freedom ◽  
Simulation Analysis ◽  
Stability Control ◽  
Vehicle Stability ◽  
Slip Ratio ◽  
Braking Performance ◽  
Braking System ◽  
The Stability

Eight degrees of freedom vehicle model was established. Using the method of fuzzy control, the ABS control algorithm was designed based on slip ratio. Simulation analysis was done at speed of 15m/s, 20m/s, 25m/s under turning braking. The results show that the vehicle braking performance and vehicle stability at middle or low speed was improved by using the ABS controller, but qualitative analysis shows that phenomenon of vehicle instability was appeared at high-speed conditions. The turning braking stability under ABS controller was judged quantificationally by the stability judging formula. The results show that the requirements of stability control could not meet with only Anti-lock Braking System.

Linear stability analysis of finite hydrodynamic journal bearing under turbulent lubrication with coupled-stress fluid

2016 ◽  
Vol 68 (3) ◽  
pp. 386-391 ◽  
Author(s):  
Abhishek Ghosh ◽  
Sisir Kumar Guha
Keyword(s):  
Stability Analysis ◽  
Newtonian Fluid ◽  
High Speed ◽  
Journal Bearing ◽  
Slenderness Ratio ◽  
Linear Perturbation ◽  
Content Type ◽  
Hydrodynamic Journal Bearing ◽  
The Stability ◽  
Coupled Stress

Purpose Several researchers have observed that to satisfy modern day’s need, it is essential to enhance the characteristics of journal bearing, which is used in numerous applications. Moreover, the use of Newtonian fluid as a lubricant is diminishing day by day, and the use of Non-Newtonian fluids is coming more into picture. Furthermore, if turbo-machinery applications are taken into account, then it can be seen that journal bearings are used for high speed applications as well. Thus, neglecting turbulent conditions may lead to erroneous results. Hence, this paper aims to present focuses on studying the stability characteristics of finite hydrodynamic journal bearing under turbulent coupled-stress lubrication. Design/methodology/approach First, the governing equation relevant to the problem is generated. Then, the dynamic analysis is carried out by linear perturbation technique, leading to three perturbed equations, which are again discretized by finite difference method. Finally, these discretized equations are solved with the help of Gauss-Seidel Iteration technique with successive over relaxation scheme. Consequently, the film response coefficients and the stability parameters are evaluated at different parametric conditions. Findings It has been concluded from the study that with increase in value of the coupled-stress parameter, the stability of the journal may increase. Whereas, with increase in Reynolds number, the stability of the journal decreases. On the other hand, stability increases with increasing values of slenderness ratio. Originality/value Researches have been performed to study the dynamic characteristics of journal bearing with non-Newtonian fluid as the lubricant. But in the class of non-Newtonian lubricants, the use of coupled-stress fluid has not yet been properly investigated. So, an attempt has been made to perform the stability analysis of bearings with coupled-stress fluid as the advanced lubricant.

Numerical and Experimental Investigation of the CeCOST Swirl Burner

2018 ◽  
Author(s):  
Erdzan Hodzic ◽  
Senbin Yu ◽  
Arman Ahamed Subash ◽  
Xin Liu ◽  
Xiao Liu ◽  
...  
Keyword(s):  
High Speed ◽  
Swirling Flow ◽  
Combustion Process ◽  
Stability Limit ◽  
Swirl Burner ◽  
Current Configuration ◽  
Stable Case ◽  
Eddy Simulation ◽  
Computational Fluid Dynamics Cfd ◽  
The Stability

Clean technology has become a key feature due to increasing environmental concerns. Swirling flows, being directly associated with combustion performance and hence minimized pollutant formation, are encountered in most propulsion and power-generation combustion devices. In this study, the development process of the conceptual swirl burner developed at the Swedish National Centre for Combustion and Technology (CeCOST), is presented. Utilizing extensive computational fluid dynamics (CFD) analysis, both the lead time and cost in manufacturing of the different burner parts were significantly reduced. The performance maps bounded by the flashback and blow-off limits for the current configuration were obtained and studied in detail using advanced experimental measurements and numerical simulations. Utilizing high speed OH-chemiluminescence, OH/CH2O-PLIF and Large Eddy Simulation (LES), details of the combustion process and flame-flow interaction are presented. The main focus is on three different cases, a stable case, a case close to blow-off and flashback condition. We show the influence of the flame on the core flow and how an increase in swirl may extend the stability limit of the anchored flame in swirling flow burners.

Deficiencies in Turbulence Modelling for the Prediction of the Stability Boundary in Highly Loaded Compressors

2019 ◽  
Author(s):  
Jose Moreno ◽  
John Dodds ◽  
Mehdi Vahdati ◽  
Sina Stapelfeldt
Keyword(s):  
High Speed ◽  
Stability Boundary ◽  
Turbulence Models ◽  
Stability Limit ◽  
Major Effect ◽  
Navier Stokes ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Multi Stage ◽  
The Stability

Abstract Reynolds-averaged Navier-Stokes (RANS) equations are employed for aerodynamic and aeroelastic modelling in axial compressors. Their solutions are highly dependent on the turbulence models for closure. The main objective of this work is to assess the widely used Spalart-Allmaras model’s suitability for compressor flows. For this purpose, an extensive investigation of the sources of uncertainties in a high-speed multi-stage compressor rig was carried out. The grid resolution near the casing end wall, which affects the tip leakage flow and casing boundary layer, was found to have a major effect on the stability limit prediction. Refinements in this region led to a stall margin loss prediction. It was found that this loss was exclusively due to the destruction term in the SA model.

Sign in / Sign up

Export Citation Format

Share Document