Influence of Intermetallic Characteristics on the Solder Joint Strength of Halogen-Free Printed Circuit Board Assembly

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Hung-Jen Chang ◽  
Jung-Hua Chou ◽  
Tao-Chih Chang ◽  
Chau-Jie Zhan ◽  
Min-Hsiung Hon ◽  
...  
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Solder Paste ◽  
Sac305 Solder ◽  
Printed Circuit ◽  
Pull Strength ◽  
Free Solder ◽  
Halogen Free ◽  
Electroless Ni

Five halogen-free (HF) dummy plastic ball grid array (PBGA) components with daisy-chains and Sn4.0Ag0.5Cu (SAC405) Pb-free solder balls were assembled on a HF high density interconnection (HDI) printed circuit board (PCB) using Sn1.0Ag0.5Cu (SAC105) and Sn3.0Ag0.5Cu (SAC305) Pb-free solder pastes, respectively. The above compositions were in weight percent. The assemblies were then experienced to moisture sensitive level testing with three times reflow at a peak temperature of 260 °C; no delamination was found present in both the component and PCB laminates. The microstructure showed that the utilization of SAC105 solder paste was beneficial in refining the Ag3Sn intermetallic compound (IMC) within the solder joint and the intermetallic layers formed at various interfaces with different Ni contents and thicknesses due to different metal finishes. The IMC spalling was found at the BGA-side interface within the solder joints formed with SAC105 solder paste but not discovered within the ones made of SAC305 solder paste. The pull strength of the solder joint formed with SAC305 solder paste was always higher than that made from SAC105 no matter on Cu or electroless Ni. Moreover, the fracture was found at the interface between the Cu foil and epoxy in the halogen-free test device. Numerical analysis showed that the thickness of IMC layer dominated the pull strength of the solder joint because the Z-axial normal stress applied to the solder joints formed with Cu and electroless Ni were 752.0 and 816.6 MPa, respectively, and a thicker IMC layer was beneficial to provide a higher pull strength of solder joint.

Site Redressing Techniques and Rework of Lead-Free Chip Scale Packages

2003 ◽  
Author(s):  
Arun Gowda ◽  
Anthony Primavera ◽  
K. Srihari
Keyword(s):  
Printed Circuit Board ◽  
Circuit Board ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
Printed Circuit ◽  
Free Solder ◽  
The Individual ◽  
Component Assembly ◽  
Free Area

The implementation of lead-free solder into an electronics assembly process necessitates the reassessment of the individual factors involved in component attachment and rework. A component assembly undergoes multiple thermal cycles during rework. With the use of lead-free solder, the assemblies are subjected to higher assembly and rework temperatures than those required for eutectic tin-lead assemblies. The rework of lead-free area array components involves the removal of defective component, preparation of the printed circuit board attachment pad (site redressing), solder paste replenishment or flux deposition, and component placement and reflow. This paper primarily focuses on the site redressing aspect of lead-free rework, followed by the development of rework processes for lead-free chip scale packages utilizing the knowledge gained in the site redressing studies.

scholarly journals The Effect of Epoxy Polymer Addition in Sn-Ag-Cu and Sn-Bi Solder Joints

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 960 ◽  
Author(s):  
Min-Soo Kang ◽  
Do-Seok Kim ◽  
Young-Eui Shin
Keyword(s):  
Solder Joint ◽  
Strain Energy ◽  
Printed Circuit Board ◽  
Solder Joints ◽  
Circuit Board ◽  
Solder Paste ◽  
Element Analysis ◽  
Printed Circuit ◽  
Shock Testing ◽  
Polymer Addition

To analyze the reinforcement effect of adding polymer to solder paste, epoxies were mixed with two currently available Sn-3.0Ag-0.5Cu (wt.% SAC305) and Sn-59Bi (wt.%) solder pastes and specimens prepared by bonding chip resistors to a printed circuit board. The effect of repetitive thermal stress on the solder joints was then analyzed experimentally using thermal shock testing (−40 °C to 125 °C) over 2000 cycles. The viscoplastic stress–strain curves generated in the solder were simulated using finite element analysis, and the hysteresis loop was calculated. The growth and propagation of cracks in the solder were also predicted using strain energy formulas. It was confirmed that the epoxy paste dispersed the stress inside the solder joint by externally supporting the solder fillet, and crack formation was suppressed, improving the lifetime of the solder joint.

Materials Characterization of Lead Free Compositions for Minimum Temperature SMT Processes at the SLI-Second Level Interconnect Solder Joint

2004 ◽  
Author(s):  
Norman J. Armendariz ◽  
Prawin Paulraj
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Gold Surface ◽  
Circuit Board ◽  
Lead Free ◽  
Processing Temperature ◽  
The European Union ◽  
Printed Circuit ◽  
Higher Temperature ◽  
Tin Silver Copper

Abstract The European Union is banning the use of Pb in electronic products starting July 1st, 2006. Printed circuit board assemblies or “motherboards” require that planned CPU sockets and BGA chipsets use lead-free solder ball compositions at the second level interconnections (SLI) to attach to a printed circuit board (PCB) and survive various assembly and reliability test conditions for end-use deployment. Intel is pro-actively preparing for this anticipated Pb ban, by evaluating a new lead free (LF) solder alloy in the ternary Tin- Silver-Copper (Sn4.0Ag0.5Cu) system and developing higher temperature board assembly processes. This will be pursued with a focus on achieving the lowest process temperature required to avoid deleterious higher temperature effects and still achieve a metallurgically compatible solder joint. One primary factor is the elevated peak reflow temperature required for surface mount technology (SMT) LF assembly, which is approximately 250 °C compared to present eutectic tin/lead (Sn37Pb) reflow temperatures of around 220 °C. In addition, extended SMT time-above-liquidus (TAL) and subsequent cooling rates are also a concern not only for the critical BGA chipsets and CPU BGA sockets but to other components similarly attached to the same PCB substrate. PCBs used were conventional FR-4 substrates with organic solder preservative on the copper pads and mechanical daisychanged FCBGA components with direct immersion gold surface finish on their copper pads. However, a materials analysis method and approach is also required to characterize and evaluate the effect of low peak temperature LF SMT processing on the PBA SLI to identify the absolute limits or “cliffs” and determine if the minimum processing temperature and TAL could be further lowered. The SLI system is characterized using various microanalytical techniques, such as, conventional optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and microhardness testing. In addition, the SLI is further characterized using macroanalytical techniques such as dye penetrant testing (DPT) with controlled tensile testing for mechanical strength in addition to disbond and crack area mapping to complete the analysis.

Experimental Investigation by Speckle Interferometry of Solder Joint Failure Under Thermomechanical Load Aggravated by Boundary Conditions at Board Level

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
D. N. Borza ◽  
I. T. Nistea
Keyword(s):  
Solder Joint ◽  
Fundamental Frequency ◽  
Printed Circuit Board ◽  
Speckle Interferometry ◽  
Circuit Board ◽  
Joint Failure ◽  
Printed Circuit ◽  
Out Of Plane ◽  
Fringe Patterns ◽  
Board Level

Reliability of electronic assemblies at board level and solder joint integrity depend upon the stress applied to the assembly. The stress is often of thermomechanical or of vibrational nature. In both cases, the behavior of the assembly is strongly influenced by the mechanical boundary conditions created by the printed circuit board (PCB) to casing fasteners. In many previously published papers, the conditions imposed to the fasteners are mostly aiming at an increase of the fundamental frequency and a decrease of static or dynamic displacement values characterizing the deformation. These conditions aim at reducing the fatigue in different parts of these assemblies. In the photomechanics laboratory of INSA Rouen, the origins of solder joint failure have been investigated by means of full-field measurements of the flexure deformation induced by vibrations or by forced thermal convection. The measurements were done both at a global level for the whole printed circuit board assembly (PCBA) and at a local level at the solder joints where failure was reported. The experimental technique used was phase-stepped laser speckle interferometry. This technique has a submicrometer sensitivity with respect to out-of-plane deformations induced by bending and its use is completely nonintrusive. Some of the results were comforted by comparison with a numerical finite elements model. The experimental results are presented either as time-average holographic fringe patterns, as in the case of vibrations, or as wrapped phase patterns, as in the case of deformation under thermomechanical stress. Both types of fringe patterns may be processed so as to obtain the explicit out-of-plane static deformation (or vibration amplitude) maps. Experimental results show that the direct cause of solder joint failure may be a high local PCB curvature produced by a supplementary fastening screw intended to reduce displacements and increase fundamental frequency. The curvature is directly responsible for tensile stress appearing in the leads of a large quad flat pack (QFP) component and for shear in the corresponding solder joints. The general principle of increasing the fundamental frequency and decreasing the static or dynamic displacement values has to be checked against the consequences on the PCB curvature near large electronic devices having high stiffness.

Numerical Model to Simulate the Drop Test of Printed Circuit Board (PCB)

2011 ◽  
Vol 423 ◽  
pp. 26-30
Author(s):  
S. Assif ◽  
M. Agouzoul ◽  
A. El Hami ◽  
O. Bendaou ◽  
Y. Gbati
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Drop Test ◽  
Dynamic Responses ◽  
Circuit Board ◽  
Joint Stress ◽  
Printed Circuit ◽  
Increasing Demand ◽  
Improved Model ◽  
Board Level

Increasing demand for smaller consumer electronic devices with multi-function capabilities has driven the packaging architectures trends for the finer-pitch interconnects, thus increasing chances of their failures. A simulation of the Board Level Drop-Test according to JEDEC (Joint Electron Device Council) is performed to evaluate the solder joint reliability under drop impact test. After good insights to the physics of the problem, the results of the numerical analysis on a simple Euler-Bernoulli beam were validated against analytical analysis. Since the simulation has to be performed on ANSYS Mechanical which is an implicit software, two methods were proposed, the acceleration-input and the displacement-input. The results are the same for both methods. Therefore, the simulation is carried on the real standard model construction of the board package level2. Then a new improved model is proposed to satisfy shape regular element and accuracy. All the models are validated to show excellent first level correlation on the dynamic responses of Printed Circuit Board, and second level correlation on solder joint stress. Then a static model useful for quick design analysis and optimization’s works is proposed and validated. Finally, plasticity behavior is introduced on the solder ball and a non-linear analysis is performed.

Failure Analysis of Halogen-Free Printed Circuit Board Assembly Under Board-Level Drop Test

2012 ◽  
Vol 134 (1) ◽  
Author(s):  
Hung-Jen Chang ◽  
Chau-Jie Zhan ◽  
Tao-Chih Chang ◽  
Jung-Hua Chou
Keyword(s):  
Printed Circuit Board ◽  
Drop Test ◽  
Circuit Board ◽  
Printed Circuit Board Assembly ◽  
Printed Circuit ◽  
Plastic Ball ◽  
Circuit Board Assembly ◽  
Halogen Free ◽  
Board Level ◽  
The Impact

In this study, a lead-free dummy plastic ball grid array component with daisy-chains and Sn4.0Ag0.5Cu Pb-free solder balls was assembled on an halogen-free high density interconnection printed circuit board (PCB) by using Sn1.0Ag0.5Cu solder paste on the Cu pad surfaces of either organic solderable preservative (OSP) or electroless nickel immersion gold (ENIG). The assembly was tested for the effect of the formation extent of Ag3Sn intermetallic compound. Afterward a board-level pulse-controlled drop test was conducted on the as-reflowed assemblies according to the JESD22-B110 and JESD22-B111 standards, the impact performance of various surface finished halogen-free printed circuit board assembly was evaluated. The test results showed that most of the fractures occurred around the pad on the test board first. Then cracks propagated across the outer build-up layer. Finally, the inner copper trace was fractured due to the propagated cracks, resulting in the failure of the PCB side. Interfacial stresses numerically obtained by the transient stress responses supported the test observation as the simulated initial crack position was the same as that observed.

Printed Circuit Board Pad Crater Test Methods and Sample Design

2012 ◽  
Author(s):  
Todd Embree ◽  
Deassy Novita ◽  
Gary Long ◽  
Satish Parupalli
Keyword(s):  
Test Data ◽  
Printed Circuit Board ◽  
Test Methods ◽  
Circuit Board ◽  
Lead Free ◽  
Sample Design ◽  
Printed Circuit ◽  
Highly Sensitive ◽  
Halogen Free ◽  
Lead Free Solders

The continual drive toward smaller second level interconnect dimensions, along with the introduction of Halogen-Free circuit board materials and increased process temperatures of Lead-Free solders, have all contributed to a more frequent occurrence of Pad Crater damage in circuit board materials during manufacturing and test processes. This paper addresses the methodology and test data of some common industry methods used to evaluate Pad Crater strength in circuit board materials. Pad Crater test data is highly sensitive to sample design; as a result a discussion of sample design criteria is also included.

Sign in / Sign up

Export Citation Format

Share Document