Experimental Investigation on Freezing of Water Falling Film on Vertical Bank of Cold Horizontal Tubes

2012 ◽  
Vol 4 (4) ◽  
Author(s):  
Hani H. Sait ◽  
Ahmed Hussain ◽  
Abduzahir M. Selim
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Ice Formation ◽  
Subzero Temperature ◽  
Falling Film ◽  
Stagnant Water ◽  
Overall Heat Transfer Coefficient ◽  
Horizontal Tubes ◽  
Internally Cooled

The heat exchangers for ice formation on tube essentially consists of cold pipes submersed in stagnant water or in a cross flow of water. The heat exchanger considered here is a falling film one. Water falling film falls down over a set of vertical in-line cold horizontal tubes. The falling film main modes are droplets, jets, and sheet depending on its flow rate. The tubes are internally cooled by a controlled subzero temperature coolant. The coolant passes through the pipes in parallel. Water falling film freezes gradually outside the test tubes. The quantity of ice formed on the test tubes is observed, photographed, and measured at different times for different falling film modes. It has been noticed that the rate of ice formation decreases with time as ice accumulates on the test tubes. The overall heat transfer coefficient decreases as more ice accumulates on the test tubes.

The Effect of Baffles in Shell and Tube Heat Exchangers

2009 ◽  
Vol 62-64 ◽  
pp. 694-699 ◽  
Author(s):  
E. Akpabio ◽  
I.O. Oboh ◽  
E.O. Aluyor
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Proper Position ◽  
Process Industries ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube ◽  
Optimal Values ◽  
Side Flow

Shell and tube heat exchangers in their various construction modifications are probably the most widespread and commonly used basic heat exchanger configuration in the process industries. There are many modifications of the basic configuration which can be used to solve special problems. Baffles serve two functions: Most importantly, they support the tubes in the proper position during assembly and operation and prevent vibration of the tubes caused by flow-induced eddies, and secondly, they guide the shell-side flow back and forth across the tube field, increasing the velocity and the heat transfer coefficient. The objective of this paper is to find the baffle spacing at fixed baffle cut that will give us the optimal values for the overall heat transfer coefficient. To do this Microsoft Excel 2003 package was employed. The results obtained from previous studies showed that to obtain optimal values for the overall heat transfer coefficient for the shell and tube heat exchangers a baffle cut of 20 to 25 percent of the diameter is common and the maximum spacing depends on how much support the tubes need. This was used to validate the results obtained from this study.

Analisis Perbandingan Jenis Material Penukar Kalor Plat Datar Aliran Silang Untuk Proses Pengeringan Kayu

2021 ◽  
Vol 9 (1) ◽  
pp. 60-71
Author(s):  
Abeth Novria Sonjaya ◽  
Marhaenanto Marhaenanto ◽  
Mokhamad Eka Faiq ◽  
La Ode M Firman
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Flat Plate ◽  
Heat Exchangers ◽  
Fluid Dynamic ◽  
Cross Flow ◽  
Plate Heat ◽  
Dry Air ◽  
Copper Material ◽  
Plate Type

The processed wood industry urgently needs a dryer to improve the quality of its production. One of the important components in a dryer is a heat exchanger. To support a durable heat transfer process, a superior material is needed. The aim of the study was to analyze the effectiveness of the application of cross-flow flat plate heat exchangers to be used in wood dryers and compare the materials used and simulate heat transfer on cross-flow flat plate heat exchangers using Computational Fluid Dynamic simulations. The results showed that there was a variation in the temperature out of dry air and gas on the flat plate heat exchanger and copper material had a better heat delivery by reaching the temperature out of dry air and gas on the flat plate type heat exchanger of successive cross flow and.   overall heat transfer coefficient value and the effectiveness value of the heat exchanger of the heat transfer characteristics that occur with the cross-flow flat plate type heat exchanger in copper material of 251.74725 W/K and 0.25.

Binary Particle Mixtures as a Heat Transfer Media in Shell-and-Plate Moving Packed Bed Heat Exchangers

2021 ◽  
Author(s):  
Chase Ellsworth Christen
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Particle Size ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Packed Bed ◽  
Particle Sizes ◽  
Overall Heat Transfer Coefficient ◽  
Solid Media

Solid particles are being considered in several high temperature thermal energy storage systems and as heat transfer media in concentrated solar power (CSP) plants. The downside of such an approach is the low overall heat transfer coefficients in shell-and-plate moving packed bed heat exchangers caused by the inherently low packed bed thermal conductivity values of the low-cost solid media. Choosing the right particle size distribution of currently available solid media can make a substantial difference in packed bed thermal conductivity, and thus, a substantial difference in the overall heat transfer coefficient of shell-and-plate moving packed bed heat exchangers. Current research exclusively focuses on continuous unimodal distributions of alumina particles. The drawback of this approach is that larger particle sizes require wider particle channels to meet flowability requirements. As a result, only small particle sizes with low packed bed thermal conductivities have been considered for the use in the falling-particle Gen3 CSP concepts. Here, binary particle mixtures, which are defined in this thesis as a mixture of two continuous unimodal particle distributions leading to a continuous bimodal particle distribution, are considered to increase packed bed thermal conductivity, decrease packed bed porosity, and improve moving packed bed heat exchanger performance. This is the first study related to CSP solid particle heat transfer that has considered the packed bed thermal conductivity and moving packed bed heat exchanger performance of bimodal particle size distributions at room and elevated temperatures. Considering binary particle mixtures that meet particle sifting segregation criteria, the overall heat transfer coefficient of shell-and-plate moving packed bed heat exchangers can be increased by 23% when compared to a monodisperse particle system. This work demonstrates that binary particle mixtures should be seriously considered to improve shell-and-plate moving packed bed heat exchangers.

Heat transfer enhancement using alumina and fly ash nanofluids in parallel and cross-flow concentric tube heat exchangers

2016 ◽  
Vol 89 (3) ◽  
pp. 414-424 ◽  
Author(s):  
Adnan Sözen ◽  
H. İbrahim Variyenli ◽  
M. Bahadır Özdemir ◽  
Metin Gürü ◽  
İpek Aytaç
Keyword(s):  
Heat Transfer ◽  
Fly Ash ◽  
Heat Transfer Enhancement ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Transfer Enhancement

Wettability Effects on Falling Film Flow and Heat Transfer Over Horizontal Tubes in Jet Flow Mode

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Avijit Karmakar ◽  
Sumanta Acharya
Keyword(s):  
Heat Transfer ◽  
Contact Angle ◽  
Nusselt Number ◽  
Film Flow ◽  
Jet Flow ◽  
Equilibrium Contact Angle ◽  
Flow Mode ◽  
Falling Film ◽  
Tube Surface ◽  
Horizontal Tubes

Abstract The performance of a falling-film heat exchanger is strongly linked to the surface characteristics and the heat transfer processes that take place over the tubes. The primary aim of this numerical study is to characterize the influence of surface wettability on the film flow behavior and its associated surface heat transfer in the jet-flow mode. Volume of fluid (VOF) based simulations are carried out for horizontal tubes with different surface wettabilities. The wettability of the tube surfaces is represented using the Kistler's dynamic contact angle model. Surface wettability effects ranging from superhydrophilic to superhydrophobic are studied by varying the equilibrium contact angle from 2 deg to 175 deg. Two different liquid mass flow rates of 0.06 and 0.18 kg/m-s corresponding to the inline and staggered jet flow modes are studied. Results are presented in terms of the liquid film thickness, the contact areas between the different phases (solid–liquid and liquid–air), and the heat transfer coefficient or Nusselt number. The resistance imposed by the increasing contact angles inhibits the extent of the liquid spreading over the tube surface, and this, in turn, influences the liquid film thickness, and the wetted area of the tube surface. A significant decrement in the heat transfer rate from the tube surfaces was observed as the equilibrium contact angle increased from 2 deg to 175 deg. The local distributions of the Nusselt number over the tube surface are strongly influenced by the flow recirculation in the liquid bulk.

Sign in / Sign up

Export Citation Format

Share Document