Experimental Study on Mechanical Properties of Epoxy/MWCNT Nanocomposites—Effects of Acid Treatment, Pressured Curing, and Liquid Rubber

2012 ◽  
Vol 3 (1) ◽  
Author(s):  
Yuan Li ◽  
Ning Hu ◽  
Takashi Kojima ◽  
Takaomi Itoi ◽  
Tomonori Watanabe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Nanotube ◽  
Acid Treatment ◽  
Tensile Tests ◽  
Type I ◽  
Multiwalled Carbon ◽  
Liquid Rubber ◽  
Type Iv ◽  
Positive Effect

The unique properties of carbon nanotube (CNT) have made it very attractive as reinforcement in polymer nanocomposites in the hope of effectively improving the mechanical properties. In order to explore the effects of three appealing influencing factors, i.e., acid treatment, pressured curing, and liquid rubber (LR) on mechanical properties of nanocomposites, tensile tests, and single-edge notched bending (SENB) tests are carried out for four types of CNT-reinforced nanocomposites. Compared with type I of nanocomposites using pristine multiwalled carbon nanotube (MWCNT) as reinforcement for epoxy, which are termed as Epoxy/MWCNT, type II of Epoxy/MWCNT-COOH nanocomposites with acid-treated MWCNTs as reinforcement, show obvious improvement on tensile properties and fracture toughness. This positive effect of acid treatment can be attributed to better dispersion of CNTs and stronger interface based on the corresponding fracture surfaces. For type III of P-Epoxy/MWCNT-COOH nanocomposites under pressured curing, although the voids in samples are decreased effectively and the interface is strengthened, there is no expected positive results because of severe CNTs agglomeration. For type IV of P-Epoxy/LR/MWCNT-COOH nanocomposites, addition of LR results in at least around a threefold increase in fracture toughness compared with that of P-Epoxy/MWCNT-COOH, indicating the amazing effect of LR. The present work provides much more choices for fabricating specific CNT-reinforced nanocomposites with desired properties by reasonably combining proper fabrication conditions including acid treatment, pressured curing, liquid rubber with polymer matrix, and reinforcement loading.

Rheological and mechanical properties of tape-casted zirconia-toughened alumina composite thick films reinforced with multiwalled carbon nanotubes

2019 ◽  
Vol 54 (17) ◽  
pp. 2353-2363
Author(s):  
SH Mussavi Rizi ◽  
M Ghatee
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Fracture Toughness ◽  
Carbon Nanotube ◽  
Phase Distribution ◽  
Thick Films ◽  
Tape Casting ◽  
Composite Films ◽  
Multiwalled Carbon ◽  
Zirconia Toughened Alumina

This paper reports the effects of adding carbon nanotubes on the mechanical properties of zirconia-toughened alumina thick films prepared by tape casting. Polyvinylpyrrolidone, polyvinyl alcohol, and glycerin were used as dispersant, binder, and plasticizer, respectively. The microstructure and phase content of the samples were studied using scanning electron microscopy and X-ray diffraction methods, respectively. Mechanical properties of thick composite films were investigated by microhardness and nanoindentation methods. It was determined that polyvinylpyrrolidone can be used as a dispersant for carbon nanotube, alumina, and zirconia particles; tape casting can produce thick films with homogeneous phase distribution, and that adding up to 0.01 wt.% carbon nanotube enhanced the zirconia-toughened alumina hardness by more than 30%, and fracture toughness about 40%. Increasing carbon nanotube content over 0.01 wt.% up to 0.1 wt.% increases microhardness and nanohardness but does not affect fracture toughness significantly.

Mechanical Properties Of Polyaniline / Multi-walled Carbon Nanotube Composite Films

2003 ◽  
Vol 791 ◽  
Author(s):  
P. C. Ramamurthy ◽  
W. R. Harrell ◽  
R. V. Gregory ◽  
B. Sadanadan ◽  
A. M. Rao
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Composite Films ◽  
Weight Percent ◽  
Organic Electronic Devices ◽  
Multiwalled Carbon ◽  
Multi Walled Carbon Nanotube ◽  
Contact Devices ◽  
Carbon Nanotube Composite

ABSTRACTHigh molecular weight polyaniline / multi-walled carbon nanotube composite films were fabricated using solution processing. Composite films with various weight percentages of multiwalled carbon nanotubes were fabricated. Physical properties of these composites were analyzed by thermogravimetric analysis, tensile testing, and scanning electron microscopy. These results indicate that the addition of multiwalled nanotubes to polyaniline significantly enhances the mechanical properties of the films. In addition, metal–semiconductor (composite) (MS) contact devices were fabricated, and it was observed that the current level in the films increased with increasing multiwalled nanotube content. Furthermore, it was observed that polyaniline containing one weight percent of carbon nanotubes appears to be the most promising composition for applications in organic electronic devices.

Electrical and mechanical properties of flexible multiwalled carbon nanotube/poly (dimethylsiloxane) based nanocomposite sheets

2021 ◽  
pp. 106550
Author(s):  
Leema Rose Viannie ◽  
N.R. Banapurmath ◽  
Manzoore Elahi M. Soudagar ◽  
Anilkumar V. Nandi ◽  
Nazia Hosain ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotube ◽  
Multiwalled Carbon Nanotube ◽  
Multiwalled Carbon

Fabrication of Carbon Nanotube Reinforced Boron Carbide Composite by Hot-Pressing Following Extrusion Molding

2014 ◽  
Vol 616 ◽  
pp. 27-31 ◽  
Author(s):  
Tomohiro Kobayashi ◽  
Katsumi Yoshida ◽  
Toyohiko Yano
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Elastic Modulus ◽  
Carbon Nanotube ◽  
Boron Carbide ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Bending Strength ◽  
Extrusion Direction ◽  
Sem Observation

The CNT/B4C composite with Al2O3 additive was fabricated by hot-pressing following extrusion molding of a CNT/B4C paste, and mechanical properties of the obtained composite were investigated. Many CNTs in the composite aligned along the extrusion direction from SEM observation. 3-points bending strength of the composite was slightly lower than that of the monolithic B4C. Elastic modulus and Vickers hardness of the composite drastically decreased with CNT addition. Fracture toughness of the composite was higher than that of the monolithic B4C.

Structural and mechanical properties of free-standing multiwalled carbon nanotube paper prepared by an aqueous mediated process

2017 ◽  
Vol 52 (12) ◽  
pp. 7503-7515 ◽  
Author(s):  
Sushant Sharma ◽  
Bhanu Pratap Singh ◽  
Arun Singh Babal ◽  
Satish Teotia ◽  
Jeevan Jyoti ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotube ◽  
Multiwalled Carbon Nanotube ◽  
Free Standing ◽  
Multiwalled Carbon

scholarly journals Silicon Nitride-Based Composites with the Addition of CNTs—A Review of Recent Progress, Challenges, and Future Prospects

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2799
Author(s):  
Awais Qadir ◽  
Péter Pinke ◽  
Ján Dusza
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Nanotube ◽  
Silicon Nitride ◽  
Wear Rate ◽  
Recent Progress ◽  
Bending Strength ◽  
Microstructure Development ◽  
Future Prospects ◽  
Microstructure Characteristics

In this overview, the results published to date concerning the development, processing, microstructure characteristics, and properties of silicon nitride/carbon nanotube (Si3N4 + CNTs) composites are summarized. The influence of the different processing routes on the microstructure development of the Si3N4 + CNTs is discussed. The effects of the CNTs addition on the mechanical properties—hardness, bending strength and fracture toughness—and tribological characteristics—wear rate and coefficient of friction—are summarized. The characteristic defects, fracture origins, toughening and damage mechanisms occurring during the testing are described. The influence of the CNTs’ addition on the thermal and functional properties of the composites is discussed as well. New trends in the development of these composites with significant potential for future applications are outlined.

Mechanical and thermal properties of PP/compatibilized PP/acid treated SWNTs nanocomposites: Effect of different acid treatment times

e-Polymers ◽  
2008 ◽  
Vol 8 (1) ◽  
Author(s):  
Morteza Ghorbanzadeh Ahangari ◽  
Abdolhosein Fereidoon ◽  
Seyfolah Saedodin
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Acid Treatment ◽  
Treatment Process ◽  
Tensile Tests ◽  
Acid Mixture ◽  
Mechanical And Thermal Properties ◽  
Thermal And Mechanical Properties ◽  
Maleated Polypropylene ◽  
Carboxylic Groups

AbstractIn the present work, the effect of different acid treatment times of singlewalled carbon nanotubes (SWNTs) on the mechanical and thermal properties of polypropylene (PP)/maleated polypropylene (PP-g-MA) nanocomposites was investigated. The acid treatment process was based on a mixture of concentrated sulphuric and nitric acids. The SWNTs were treated with the acid mixture for 1, 3, and 6 h. FTIR, Raman spectroscopy and TEM revealed the values of carboxylic groups, graphitization and morphology of acid treated SWNTs, respectively. The thermal and mechanical properties and the morphology of nanocomposites were investigated by tensile tests, DMTA, DSC, and SEM.

Effect of Carbon Nanotube on Electrical, Thermal and Mechanical Properties of Epoxy

2007 ◽  
Author(s):  
Yuanxin Zhou ◽  
Peixuan Wu ◽  
Zhongyang Cheng ◽  
Biddut Kanti Dey ◽  
Shaik Jeelani
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Nanotube ◽  
High Speed ◽  
Mechanical Test ◽  
High Vacuum ◽  
Mechanical Analysis ◽  
Thermal And Mechanical Properties ◽  
Multi Walled Carbon Nanotubes ◽  
Mechanical Agitator

In this study, electrical, thermal and mechanical properties of multi-walled carbon nanotubes (CNTs) reinforced Epon 862 epoxy have been evaluated. Firstly, 0.1 wt%, 0.2 wt%, 0.3 wt%, and 0.4 wt% CNT were infused into epoxy through a high intensity ultrasonic liquid processor and then mixed with EpiCure curing agent W using a high speed mechanical agitator. The trapped air and reaction volatiles were removed from the mixture using a high vacuum. Neat epoxy sample also was made as reference. Electrical conductivity, dynamic mechanical analysis (DMA, three point bending tests and fracture tests were performed on unfilled, CNT-filled epoxy to identify the loading effect on the properties of composites. Experimental results show significant improvement in electric conductivity. The resistivity of epoxy decreased to 15Ωm with 0.4% CNT. DMA studies revealed that filling the carbon nanotube into epoxy can produce a 90% enhancement in storage modulus and a 17° C increase in Tg, but CNT has little effect on decomposing temperature. Mechanical test results showed that modulus increased with higher CNT loading percentages, but the 0.3 wt% CNT-infusion system showed the maximum strength and fracture toughness enhancement. The decrease in strength and fracture toughness in 0.4% CNT/epoxy was attributed to poor dispersions of nanotubes in the composite.

Sign in / Sign up

Export Citation Format

Share Document