Mechanical Characterization of Porcine Skin Starting Material

2021 ◽  
Author(s):  
Bin Zhang ◽  
Shawn Chester ◽  
Siva Nadimpalli ◽  
Justin Suriano ◽  
David Theis ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Medical Devices ◽  
Tensile Tests ◽  
Starting Material ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Porcine Skin ◽  
Curve Fit ◽  
Tensile Curve ◽  
Industrial Standards

Abstract Porcine skin has been used as a starting material in several released mesh medical devices. Although this controlled animal derived material is prevalent in tissue engineered medical devices, little is known about its mechanical properties. This study mechanically characterized Porcine Skin Starting Material (PSSM), provided by Midwest Research Swine. Uniaxial tensile tests were performed on samples cut from different regions (back and neck) and orientations (parallel and perpendicular to the spine) on the PSSM. The stress-stretch relationship was determined for each sample utilizing a load frame equipped with a Digital Image Correlation measurement system. The PSSM skin demonstrates the classic nonlinear and linear regions seen in other biologic tissues. A bilinear curve fit method was used to separate the nonlinear and linear regions of the tensile curve, and each region was analyzed with an Ogden and linear model respectively. The results show that the tensile curve is better described with this method as opposed to analyzing the full curve with one model. A comparison was made between samples cut from the different regions and orientations. There were significant differences between the failure measures and mechanical indices from the two regions, and on average the back behaved anisotropically and the neck isotropically. The PSSM mechanical properties from this study could serve as a preliminary guide for those exploring devices or processes in the tissue engineering field. The methods demonstrated in this study could also help characterize other biologic materials, and be used towards the development of tissue specific industrial standards.

Comprehensive study on mechanical properties of coated biaxial warp-knitted fabrics

2021 ◽  
pp. 073168442110204
Author(s):  
Bin Yang ◽  
Yingying Shang ◽  
Zeliang Yu ◽  
Minger Wu ◽  
Youji Tao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Failure Modes ◽  
Least Squares Method ◽  
Tensile Tests ◽  
Tensile Creep ◽  
Base Layer ◽  
Sustained Load ◽  
Uniaxial Tensile ◽  
Membrane Structures ◽  
Knitted Fabrics

In recent years, coated fabrics have become the major material used in membrane structures. Due to the special structure of base layer and mechanical properties, coated biaxial warp-knitted fabrics are increasingly applied in pneumatic structures. In this article, the mechanical properties of coated biaxial warp-knitted fabrics are investigated comprehensively. First, off-axial tensile tests are carried out in seven in-plane directions: 0°, 15°, 30°, 45°, 60°, 75°, and 90°. Based on the stress–strain relationship, tensile strengths are obtained and failure modes are studied. The adaptability of Tsai–Hill criterion is analyzed. Then, the uniaxial tensile creep test is performed under 24-h sustained load and the creep elongation is calculated. Besides, tearing strengths in warp and weft directions are obtained by tearing tests. Finally, the biaxial tensile tests under five different load ratios of 1:1, 2:1, 1:2, 1:0, and 0:1 are carried out, and the elastic constants and Poisson’s ratio are calculated using the least squares method based on linear orthotropic assumption. Moreover, biaxial specimens under four load ratios of 3:1, 1:3, 5:1, and 1:5 are further tensile tested to verify the adaptability of linear orthotropic model. These experimental data offer a deeper and comprehensive understanding of mechanical properties of coated biaxial warp-knitted fabrics and could be conveniently adopted in structural design.

scholarly journals Effect of PWHT on the Microstructure and Mechanical Properties of Friction Stir Welded DP780 Steel

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1097
Author(s):  
Umer Masood Chaudry ◽  
Seung-Chang Han ◽  
Fathia Alkelae ◽  
Tea-Sung Jun
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Tensile Elongation ◽  
Image Correlation ◽  
Frictional Heat ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Dp780 Steel

In the present study, the effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties of friction stir welded (FSW) DP780 steel sheets was investigated. FSW was carried out at a constant tool rotation speed of 400 rpm and different welding speeds (200 mm/min and 400 min/min). A defect free weld was witnessed for both of the welding conditions. The mutual effect of severe plastic deformation and frictional heat generation by pin rotation during the FSW process resulted in grain refinement due to dynamic recrystallization in the stir zone (SZ) and thermo-mechanically affected zone (TMAZ). Lower tensile elongation and higher yield and ultimate tensile strengths were recorded for welded-samples as compared to the base material (BM) DP780 steel. The joints were subsequently annealed at various temperatures at 450–650 °C for 1 h. At higher annealing temperature, the work hardening rate of joints gradually decreased and subsequently failed in the softened heat-affected zone (HAZ) during the uniaxial tensile test. Reduction in yield strength and tensile strength was found in all PWHT conditions, though improvement in elongation was achieved by annealing at 550 °C. The digital image correlation analysis showed that an inhomogeneous strain distribution occurred in the FSWed samples, and the strain was particularly highly localized in the advancing side of interface zone. The nanoindentation measurements covering the FSWed joint were consistent with an increase of the annealing temperature. The various grains size in the BM, TMAZ, and SZ is the main factor monitoring the hardness distribution in these zones and the observed discrepancies in mechanical properties.

scholarly journals Strength Enhancement of Superduplex Stainless Steel Using Thermomechanical Processing

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1094
Author(s):  
M. A. Lakhdari ◽  
F. Krajcarz ◽  
J. D. Mithieux ◽  
H. P. Van Landeghem ◽  
M. Veron
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Thermomechanical Processing ◽  
Tensile Tests ◽  
Image Correlation ◽  
Strength Enhancement ◽  
Industrial Material ◽  
Superduplex Stainless Steel ◽  
The Impact ◽  
Strength Improvement

The impact of microstructure evolution on mechanical properties in superduplex stainless steel UNS S32750 (EN 1.4410) was investigated. To this end, different thermomechanical treatments were carried out in order to obtain clearly distinct duplex microstructures. Optical microscopy and scanning electron microscopy, together with texture measurements, were used to characterize the morphology and the preferred orientations of ferrite and austenite in all microstructures. Additionally, the mechanical properties were assessed by tensile tests with digital image correlation. Phase morphology was not found to significantly affect the mechanical properties and neither were phase volume fractions within 13% of the 50/50 ratio. Austenite texture was the same combined Goss/Brass texture regardless of thermomechanical processing, while ferrite texture was mainly described by α-fiber orientations. Ferrite texture and average phase spacing were found to have a notable effect on mechanical properties. One of the original microstructures of superduplex stainless steel obtained here shows a strength improvement by the order of 120 MPa over the industrial material.

Effect of Polyvinyl Alcohol Concentration on the Mechanical Properties of Collagen/Polyvinyl Alcohol Blends

2015 ◽  
Vol 732 ◽  
pp. 161-164 ◽  
Author(s):  
Jan Vesely ◽  
Lukas Horny ◽  
Hynek Chlup ◽  
Milos Beran ◽  
Milan Krajicek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Stress ◽  
Polyvinyl Alcohol ◽  
Modulus Of Elasticity ◽  
Tensile Tests ◽  
Ultimate Tensile Stress ◽  
Alcohol Concentration ◽  
Uniaxial Tensile ◽  
Initial Modulus ◽  
Water Saturated

The effects of the polyvinyl alcohol (PVA) concentration on mechanical properties of hydrogels based on blends of native or denatured collagen / PVA were examined. Blends of PVA with collagen were obtained by mixing the solutions in different ratios, using glycerol as a plasticizer. The solutions were cast on polystyrene plates and the solvent was allowed to evaporate at room temperature. Uniaxial tensile tests were performed in order to obtain the initial modulus of elasticity (up to deformation 0.1), the ultimate tensile stress and the deformation at failure of the material in the water-saturated hydrogel form. It was found that the material was elastic and the addition of PVA helped to enhance both the ultimate tensile stress and modulus of elasticity of the films. Samples prepared from denaturated collagen showed the higher ultimate tensile stress and the deformation at failure in comparison with those prepared from native collagen. The results suggest that we could expect successful application of the collagen/PVA biomaterial for tissue engineering.

Mechanical properties of PVDF-coated fabric under tensile tests

2015 ◽  
Vol 35 (4) ◽  
pp. 377-390 ◽  
Author(s):  
Andrzej Ambroziak
Keyword(s):  
Mechanical Properties ◽  
Polyvinylidene Fluoride ◽  
Cyclic Load ◽  
Tensile Tests ◽  
Woven Fabrics ◽  
Uniaxial Tensile ◽  
Cyclic Tests ◽  
Comprehensive Investigation ◽  
Coated Fabric ◽  
Coated Fabrics

Abstract This article describes the laboratory tests necessary to identify the mechanical properties of the polyvinylidene fluoride (PVDF)-coated fabrics named Precontraint 1202S and Precontraint 1302S. First, a short survey of the literature concerning the description of coated woven fabrics is presented. Second, the material parameters for PVDF-coated fabrics are specified on the basis of biaxial tensile tests. A comparison of the 1:1 biaxial and the uniaxial tensile tests results is also given. Additionally, biaxial cyclic tests were performed to observe the change of immediate mechanical properties under cyclic load. The article is aimed as an introduction to a comprehensive investigation of the mechanical properties of coated fabrics.

Correlation among Microstructure, Texture, and Properties along the Thickness Direction in As-Hot-Rolled and As-Solution-Quenched Al7055 Thick Plates

2021 ◽  
Vol 1026 ◽  
pp. 65-73
Author(s):  
Kai Zhu ◽  
Hong Wei Yan
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Tensile Tests ◽  
Rolled Plate ◽  
Uniaxial Tensile ◽  
Thickness Direction ◽  
Electron Backscattered Diffraction ◽  
Thick Plates ◽  
Aluminum Plates ◽  
Hot Rolled

Both microstructure inhomogeneity and mechanical property diversity along the thickness direction in rolled thick aluminum plates have been considered to have a remarkable impact on the performance and properties of the products made from the plates. In this study, scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD) characterizations of microstructure and texture types along the thickness directions of Al7055 thick plate specimens prepared using two conditions, hot-rolling and solution-quenching, were performed. To examine the mechanical properties, uniaxial tensile tests were also carried out on specimens machined from both types of thick plates, using a layered strategy along the thickness direction. The results indicate that both the microstructure and mechanical properties are inhomogeneous under the two conditions. Furthermore, it is evident that there is a hereditary relationship between the mechanical properties of the two plates—areas with higher yield strength in the as-hot-rolled plate correspond to areas with the higher yield strength in the as-solution-quenched plate

The tensile behaviour of biaxial and triaxial braided fabrics

2016 ◽  
Vol 47 (8) ◽  
pp. 2184-2204 ◽  
Author(s):  
Duchamp Boris ◽  
Legrand Xavier ◽  
Soulat Damien
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Mechanical Behaviour ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Tensile Behaviour ◽  
Linear Mass ◽  
Double Peak ◽  
Specific Behaviour ◽  
Braiding Angle

The tensile behaviour of braid reinforcement is classically described by the behaviour of composite elaborated from these reinforcements. Few studies concern the tensile behaviour of braided fabrics. In this paper biaxial and triaxial braids are manufactured on a braiding loom. The evolution of key parameters as linear mass and braiding angle in function of process parameters is presented. Braid reinforcements are characterized in uniaxial tensile. The mechanical behaviour is analysed and compared in function of the braiding angle, but also different kinds of braid are considered. A specific behaviour called “double-peak” is identified for triaxial braids which have a higher braiding angle. The evolution of the braiding angle measured during tensile tests gives a comprehension on the mechanical behaviour of dry braids. Associated with this experimental study, an analytical model is also proposed, to predict mechanical properties of braid reinforcements.

Cellulose Whiskers Micro-Fibers Effect in the Mechanical Proprieties of PP and PLA Composites Fibers Obtained by Spinning Process

2011 ◽  
Vol 146 ◽  
pp. 12-26 ◽  
Author(s):  
A. Gherissi ◽  
R.Ben Cheikh ◽  
E. Dévaux ◽  
Fethi Abbassi
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Tensile Tests ◽  
Advanced Materials ◽  
Uniaxial Tensile ◽  
Failure Resistance ◽  
Cellulose Whiskers ◽  
Limit Strength

In this study, we present the manufacturing process of two new composites materials in the form of long fibers of polylactic-acid (PLA) or polypropylene (PP), reinforced by cellulose whiskers micro-fibers loads. In order to evaluate the mechanical properties of these advanced materials, a several uniaxial tensile tests were carried out. The PP and the PLA have initially been spinning without the addition of cellulose whiskers micro-fibers. In order to study the effects of cellulose whiskers micro-fibers reinforcements in the Mechanical behavior of the PLA and PP filaments, we determinate the proprieties of these advanced material from the tensile results. For the PP composite filaments material case, the whiskers reinforcement increases Young's modulus and failure resistance, but it reduces the limit strength failure. For the PLA composites the addition of 1% wt of cellulose whiskers from the total volume fraction of the material, increase the Young’s modulus more than 50% and a decrease of the failure resistance and the limit strength of composite. The obtained composites fibers are very rigid and brittle. What follows, that the addition of cellulose whiskers micro fibers in PP matrix, provides mechanical properties more convenient compared to the PLA matrix.

Sign in / Sign up

Export Citation Format

Share Document