scholarly journals Direct Heat Cogeneration Applications for Kaolin Producers

1990 ◽  
Author(s):  
Jane P. Hill
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Economic Benefits ◽  
Economic Viability ◽  
Heat Recovery Steam Generator ◽  
Thermal Output ◽  
End Products ◽  
One Step ◽  
Silicate Clay

Direct heat cogeneration using gas turbines presents an unusually attractive means of supplying two end products when both are required simultaneously. Most cogeneration applications involve steam as the thermal end product. While steam has many industrial and commercial uses, the conversion of thermal output to usable steam involves losses in the heat recovery steam generator (HRSG). When the heat rejected by a gas turbine can be used directly, system losses can be minimized. One such application exists in the kaolin industry. Kaolin is a white alumina-silicate clay used in many products, including paper, medicines, plastics and paints. One step in producing kaolin requires large spray dryers, the heat for which can be supplemented by cogeneration. This study outlines conditions necessary to achieve economic viability with cogeneration and suggests ways to maximize economic benefits. Risks associated with cogeneration ventures are also discussed.

Thermodynamic Performance of Wet Compression and Regenerative (WCR) Gas Turbine

2003 ◽  
Author(s):  
Qun Zheng ◽  
Minghong Li ◽  
Yufeng Sun
Keyword(s):  
Heat Exchanger ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Regenerative Process ◽  
Specific Power ◽  
Heat Recovery Steam Generator ◽  
Thermodynamic Performance ◽  
Wet Compression ◽  
Steam Heat

Thermodynamic performance of wet compression and regenerative (WCR) gas turbine are investigated in this paper. The regenerative process can be achieved by a gas/air (and steam) heat exchanger, a regenerator, or by a heat recovery steam generator and then the steam injected into the gas turbine. Several schemes of the above wet compression and regenerative cycles are computed and analyzed. The calculated results indicate that not only a significant specific power can be obtained, but also is the WCR gas turbine an economic competitive option of efficient gas turbines.

scholarly journals Repowering of a Small Utility: A Unique Solution to a Unique Problem

1979 ◽  
Author(s):  
L. F. Fougere ◽  
H. G. Stewart ◽  
J. Bell
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Electric Utility ◽  
Combined Cycle ◽  
Steam Boiler ◽  
Heat Recovery Steam Generator ◽  
Turbine Generator

Citizens Utilities Company’s Kauai Electric Division is the electric utility on the Island of Kauai, fourth largest and westernmost as well as northernmost of the Hawaiian Islands. As a result of growing load requirements, additional generating capacity was required that would afford a high level of reliability and operating flexibility and good fuel economy at reasonable capital investment. To meet these requirements, a combined cycle arrangement was completed in 1978 utilizing one existing gas turbine-generator and one new gas turbine-generator, both exhausting to a new heat recovery steam generator which supplies steam to an existing steam turbine-generator. Damper controlled ducting directs exhaust gas from either gas turbine, one at a time, through the heat recovery steam generator. The existing oil-fired steam boiler remains available to power the steam turbine-generator independently or in parallel with the heat recovery steam generator. The gas turbines can operate either in simple cycle as peaking units or in combined cycle, one at a time, as base load units. This arrangement provides excellent operating reliability and flexibility, and the most favorable economics of all generating arrangements for the service required.

Acceptance Criteria for Heat Recovery Steam Generators Behind Gas Turbines

1986 ◽  
Author(s):  
Akber Pasha
Keyword(s):  
Gas Turbine ◽  
Steam Generator ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Design Parameters ◽  
Heat Recovery Steam Generator ◽  
Exhaust Temperature ◽  
Input Parameters ◽  
Input Variables ◽  
Gas Turbine Exhaust

The design of a Heat Recovery Steam Generator behind a gas turbine depends upon various input parameters such as gas turbine exhaust flow, exhaust temperature, etc. Most of the input parameters are either measured with tolerances or calculated based on experimental correlations. The design of the heat recovery steam generator itself utilizes various correlations and empirical values. The errors or measurement tolerances in these variables affect the performance of the steam generator. This paper describes the various design parameters, the possible magnitude of errors in these parameters and the overall effect on the steam generator’s performance. By utilizing the information given in this paper, it is possible to develop a performance envelope based on the possible error margins of the input variables. The steam generator performance can be deemed acceptable if it is within this envelope.

Evolution of Gas Turbine Intake Air Filtration in a 420 MW Cogeneration Plant

2014 ◽  
Author(s):  
Steve Ingistov ◽  
Michael Milos ◽  
Rakesh K. Bhargava
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Economic Benefits ◽  
Cogeneration Plant ◽  
Air Filtration ◽  
Air Filter ◽  
Filter System ◽  
Turbine Performance ◽  
Filtration System ◽  
Operational Data

A suitable inlet air filter system is required for a gas turbine, depending on installation site and its environmental conditions, to minimize contaminants entering the compressor section in order to maintain gas turbine performance. This paper describes evolution of inlet air filter systems utilized at the 420 MW Watson Cogeneration Plant consisting of four GE 7EA gas turbines since commissioning of the plant in November 1987. Changes to the inlet air filtration system became necessary due to system limitations, a desire to reduce operational and maintenance costs, and enhance overall plant performance. Based on approximately 2 years of operational data with the latest filtration system combined with other operational experiences of more than 25 years, it is shown that implementation of the high efficiency particulate air filter system provides reduced number of crank washes, gas turbine performance improvement and significant economic benefits compared to the traditional synthetic media type filters. Reasons for improved gas turbine performance and associated economic benefits, observed via actual operational data, with use of the latest filter system are discussed in this paper.

scholarly journals Gas Turbine Heat Recovery Steam Generators for Combined Cycles Natural or Forced Circulation Considerations

1988 ◽  
Author(s):  
Akber Pasha
Keyword(s):  
Gas Turbine ◽  
Steam Generator ◽  
Heat Recovery ◽  
Power Plants ◽  
Natural Circulation ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Steam Generators ◽  
Forced Circulation ◽  
Gas Turbine Exhaust

In recent years the combined cycle has become a very attractive power plant arrangement because of its high cycle efficiency, short order-to-on-line time and flexibility in the sizing when compared to conventional steam power plants. However, optimization of the cycle and selection of combined cycle equipment has become more complex because the three major components, Gas Turbine, Heat Recovery Steam Generator and Steam Turbine, are often designed and built by different manufacturers. Heat Recovery Steam Generators are classified into two major categories — 1) Natural Circulation and 2) Forced Circulation. Both circulation designs have certain advantages, disadvantages and limitations. This paper analyzes various factors including; availability, start-up, gas turbine exhaust conditions, reliability, space requirements, etc., which are affected by the type of circulation and which in turn affect the design, price and performance of the Heat Recovery Steam Generator. Modern trends around the world are discussed and conclusions are drawn as to the best type of circulation for a Heat Recovery Steam Generator for combined cycle application.

New Concept of a Micro Gas Turbine Based Co-Generation Package for Performance Improvement in Practical Use

2005 ◽  
Author(s):  
Kenichiro Mochizuki ◽  
Satoshi Shibata ◽  
Umeo Inoue ◽  
Toshiaki Tsuchiya ◽  
Hiroko Sotouchi ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Steam Generator ◽  
Thermal Efficiency ◽  
Heat Recovery ◽  
Steam Injection ◽  
Operating Conditions ◽  
Market Potential ◽  
Injection System ◽  
Heat Recovery Steam Generator ◽  
Micro Gas Turbine

As the energy consumption has been increasing rapidly in the commercial sector in Japan, the market potential for the micro gas turbine is significant and it will be realized substantially if the thermal efficiency is improved. One of measures is to introduce the steam injection system using the steam generated by the heat recovery steam generator. Steam injection tests have been carried out using a micro gas turbine (Capstone C60). Test results showed that key performance parameters such as power output, thermal efficiency and emissions were improved by the steam injection. The stable operation of micro gas turbine with steam injection was confirmed under various operating conditions. Consequently, a micro gas turbine based co-generation package with steam injection driven by a heat recovery steam generator (HRSG) with supplementary firing is proposed.

Gas Turbine Combined Cycle Optimized for Postcombustion Carbon Capture

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
S. Can Gülen ◽  
Chris Hall
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Co2 Capture ◽  
Carbon Capture ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Heat Recovery Steam Generator ◽  
Gas Temperature ◽  
Design Challenges ◽  
Stack Gas

This paper describes a gas turbine combined cycle (GTCC) power plant system, which addresses the three key design challenges of postcombustion CO2 capture from the stack gas of a GTCC power plant using aqueous amine-based scrubbing method by offering the following: (i) low heat recovery steam generator (HRSG) stack gas temperature, (ii) increased HRSG stack gas CO2 content, and (iii) decreased HRSG stack gas O2 content. This is achieved by combining two bottoming cycle modifications in an inventive manner, i.e., (i) high supplementary (duct) firing in the HRSG and (ii) recirculation of the HRSG stack gas. It is shown that, compared to an existing natural gas-fired GTCC power plant with postcombustion capture, it is possible to reduce the CO2 capture penalty—power diverted away from generation—by almost 65% and the overall capital cost ($/kW) by about 35%.

Combined Heat and Power: Gas Turbine Operational Flexibility

2013 ◽  
Author(s):  
James DiCampli
Keyword(s):  
Gas Turbine ◽  
Urban Areas ◽  
Gas Turbines ◽  
Heat Recovery ◽  
National Fire Protection Association ◽  
Combined Heat And Power ◽  
Combined Cycle ◽  
Electricity Production ◽  
Exhaust Heat ◽  
Gas Fuel

Combined heat and power (CHP) is an application that utilizes the exhaust heat generated from a gas turbine and converts it into a useful energy source for heating & cooling, or additional electric generation in combined cycle configurations. Compared to simple-cycle plants with no heat recovery, CHP plants emit fewer greenhouse gasses and other emissions, while generating significantly more useful energy per unit of fuel consumed. Clean plants are easier to permit, build and operate. Because of these advantages, projections show CHP capacity is expected to double and account for 24% of global electricity production by 2030. An aeroderivative power plant has distinct advantages to meet CHP needs. These include high thermal efficiency, low cost, easy installation, proven reliability, compact design for urban areas, simple operation and maintenance, fuel flexibility, and full power generation in a very short time period. There has been extensive discussion and analyses on modifying purge requirements on cycling units for faster dispatch. The National Fire Protection Association (NFPA) has required an air purge of downstream systems prior to startup to preclude potentially flammable or explosive conditions. The auto ignition temperature of natural gas fuel is around 800°F. Experience has shown that if the exhaust duct contains sufficient concentrations of captured gas fuel, and is not purged, it can ignite immediately during light off causing extensive damage to downstream equipment. The NFPA Boiler and Combustion Systems Hazards Code Committee have developed new procedures to safely provide for a fast-start capability. The change in the code was issued in the 2011 Edition of NFPA 85 and titled the Combustion Turbine Purge Credit. For a cycling plant and hot start conditions, implementation of purge credit can reduce normal start-to-load by 15–30 minutes. Part of the time saving is the reduction of the purge time itself, and the rest is faster ramp rates due to a higher initial temperature and pressure in the heat recovery steam generator (HRSG). This paper details the technical analysis and implementation of the NFPA purge credit recommendations on GE Power and Water aeroderivative gas turbines. This includes the hardware changes, triple block and double vent valve system (or drain for liquid fuels), and software changes that include monitoring and alarms managed by the control system.

Study on Gas Turbine-Based CCHP System with Multi-Objective Evaluation Index

2013 ◽  
Vol 860-863 ◽  
pp. 1366-1369 ◽  
Author(s):  
Dan Dan Sun ◽  
Cheng Yang ◽  
Fei Zeng
Keyword(s):  
Gas Turbine ◽  
Steam Generator ◽  
Heat Recovery ◽  
Objective Evaluation ◽  
Evaluation Index ◽  
Heat Recovery Steam Generator ◽  
Evaluation Indexes ◽  
Multi Objective ◽  
Combined Cooling ◽  
Weight Coefficients

Currently, there are many evaluation indexes for gas turbine-based combined cooling, heating and power （CCHP）. In this paper, a multi-objective evaluation index (MEI) model was suggested and weight coefficients were considered in the model. The CCHP system evaluated in this study was composed of gas turbine + heat recovery steam generator (HRSG ) + LiBr absorption chiller. The gas turbine-based CCHP system was evaluated and the component capacity was optimized with the proposed MEI. The study provides a reference for the allocation and operation of gas turbine-based CCHP.

scholarly journals Waste Heat Recovery for Offshore Applications

2012 ◽  
Author(s):  
Leonardo Pierobon ◽  
Rambabu Kandepu ◽  
Fredrik Haglind
Keyword(s):  
Gas Turbine ◽  
Thermal Energy ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Oil And Gas ◽  
Waste Heat ◽  
Offshore Platforms ◽  
Organic Rankine Cycles ◽  
Heat Loads

With increasing incentives for reducing the CO2 emissions offshore, optimization of energy usage on offshore platforms has become a focus area. Most of offshore oil and gas platforms use gas turbines to support the electrical demand on the platform. It is common to operate a gas turbine mostly under part-load conditions most of the time in order to accommodate any short term peak loads. Gas turbines with flexibility with respect to fuel type, resulting in low turbine inlet and exhaust gas temperatures, are often employed. The typical gas turbine efficiency for an offshore application might vary in the range 20–30%. There are several technologies available for onshore gas turbines (and low/medium heat sources) to convert the waste heat into electricity. For offshore applications it is not economical and practical to have a steam bottoming cycle to increase the efficiency of electricity production, due to low gas turbine outlet temperature, space and weight restrictions and the need for make-up water. A more promising option for use offshore is organic Rankine cycles (ORC). Moreover, several oil and gas platforms are equipped with waste heat recovery units to recover a part of the thermal energy in the gas turbine off-gas using heat exchangers, and the recovered thermal energy acts as heat source for some of the heat loads on the platform. The amount of the recovered thermal energy depends on the heat loads and thus the full potential of waste heat recovery units may not be utilized. In present paper, a review of the technologies available for waste heat recovery offshore is made. Further, the challenges of implementing these technologies on offshore platforms are discussed from a practical point of view. Performance estimations are made for a number of combined cycles consisting of a gas turbine typically used offshore and organic Rankine cycles employing different working fluids; an optimal media is then suggested based on efficiency, weight and space considerations. The paper concludes with suggestions for further research within the field of waste heat recovery for offshore applications.

Sign in / Sign up

Export Citation Format

Share Document