Nano-Scale Impact Characteristics of Rough Surfaces in Humid Atmosphere With Full or Partial SAM Protection

2008 ◽  
Author(s):  
Mircea Teodorescu ◽  
Stephanos Theodossiades ◽  
Homer Rahnejat
Keyword(s):  
Rough Surfaces ◽  
Negligible Effect ◽  
Impact Dynamics ◽  
Fundamental Physics ◽  
Humid Atmosphere ◽  
Micro Scale ◽  
Nano Scale ◽  
Fundamental Understanding ◽  
Impact Characteristics ◽  
The Impact

The impact dynamics of micro-scale mechanisms deviates from the classical theories applied to traditional macro-systems, This is because of multiplicity of forces acting in nano-scale contacts, which have negligible effect at the larger scale. A fundamental understanding of these forces and their interplay is required to advise design of such mechanisms based on fundamental physics. The paper highlights the significance of some of these forces and circumstances where their influence becomes significant.

scholarly journals A Rational Numerical Method for Simulation of Drop-Impact Dynamics of Oleo-Pneumatic Landing Gear

2021 ◽  
Vol 11 (9) ◽  
pp. 4136
Author(s):  
Rosario Pecora
Keyword(s):  
Numerical Method ◽  
Initial Conditions ◽  
Impact Load ◽  
Numerical Models ◽  
Landing Gear ◽  
Design Stage ◽  
Impact Dynamics ◽  
State Variables ◽  
Adopted Model ◽  
The Impact

Oleo-pneumatic landing gear is a complex mechanical system conceived to efficiently absorb and dissipate an aircraft’s kinetic energy at touchdown, thus reducing the impact load and acceleration transmitted to the airframe. Due to its significant influence on ground loads, this system is generally designed in parallel with the main structural components of the aircraft, such as the fuselage and wings. Robust numerical models for simulating landing gear impact dynamics are essential from the preliminary design stage in order to properly assess aircraft configuration and structural arrangements. Finite element (FE) analysis is a viable solution for supporting the design. However, regarding the oleo-pneumatic struts, FE-based simulation may become unpractical, since detailed models are required to obtain reliable results. Moreover, FE models could not be very versatile for accommodating the many design updates that usually occur at the beginning of the landing gear project or during the layout optimization process. In this work, a numerical method for simulating oleo-pneumatic landing gear drop dynamics is presented. To effectively support both the preliminary and advanced design of landing gear units, the proposed simulation approach rationally balances the level of sophistication of the adopted model with the need for accurate results. Although based on a formulation assuming only four state variables for the description of landing gear dynamics, the approach successfully accounts for all the relevant forces that arise during the drop and their influence on landing gear motion. A set of intercommunicating routines was implemented in MATLAB® environment to integrate the dynamic impact equations, starting from user-defined initial conditions and general parameters related to the geometric and structural configuration of the landing gear. The tool was then used to simulate a drop test of a reference landing gear, and the obtained results were successfully validated against available experimental data.

Measurement, analysis and prediction of amoxicillin oral dose stability from integrated molecular description approach and accelerated predictive stability (APS)

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Camille Merienne ◽  
Chloe Marchand ◽  
Samira Filali ◽  
Damien Salmon ◽  
Christine Pivot ◽  
...  
Keyword(s):  
Oral Dose ◽  
Shelf Life ◽  
Chromatographic Analysis ◽  
Water Adsorption ◽  
Degradation Mechanism ◽  
Oral Dosage ◽  
Hydroxyl Groups ◽  
Humid Atmosphere ◽  
Intramolecular Hydrogen ◽  
The Impact

AbstractBackgroundStability of low amoxicillin oral dosage form (5 mg) used in reintroduction drug test was not fully documented. Furthermore, the impact of (1) salt moiety of amoxicillin and (2) amoxicillin – excipient interactions upon the antibiotic formulation stability during the storage was not characterized so that the estimation of the pharmaceutical expiration date from shelf-life was uncertain. Thus, the main goal of this study was to estimate the shelf-life of two formulations of amoxicillin, using a semi-predictive methodology.MethodsAmoxicillin sodium (AS) and amoxicillin trihydrate (ATH), corresponding to 5-mg amoxicillin, were compounded with microcrystalline cellulose (MCC) in oral hard capsules which were, then, submitted to four environmental conditions (25 °C / 60% or 80% relative humidity (RH); 40 °C / 75% RH; 60 °C / 5% RH) in climatic chambers for 45 and 84 days. Therefore, the characterization of amoxicillin-MCC mixture was assessed by attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) The profiles of amoxicillin content (determined by stability indicating chromatographic method) as a function of storage time, temperature and RH were fitted to pre-defined kinetic models performed by accelerated predictive stability (APS).ResultsATR-FTIR analysis of AS, ATH, MCC and bulk specimens stored in heated and humid atmosphere confirmed water sorption to cellulose described by a broad and unresolved 3600 to 3000 cm−1 band associated with (1) general intramolecular and intermolecular hydrogen bonding between water and hydroxyl groups of the cellulose, and with (2) free hydroxyl in cellulose. Moreover, a dramatic decrease of absorption at 1776 and 1687 cm−1 respectively characteristic of the β-lactam ring (νC=O) and amide group (νC=O), was revealed as a consequence of AS and ATH degradation caused by moisturization of bulk. Amoxicillin degradation was established by chromatographic analysis showing faster AS degradation than ATH throughout time exposure. The combined effects of temperature – RH were successfully modeled by APS, where AS and ATH showed accelerated (auto-catalysis degradation mechanism) and linear degradation, respectively. The faster AS degradation was assumed to be linked to lower hydrogen donor to hydrogen acceptor count ratio and polar surface than ATH, increasing the probability of AS hydrolysis by water adsorption to AS-MCC solid dispersion (e.g., by reduction of protective intramolecular hydrogen bonds between AS molecules). Furthermore, the compounding which involved a drastic homogenization of solids may have affected the crystalline degree of MCC with an increase of amorphous phase more sensitive to water adsorption.ConclusionsThe improvement of amoxicillin compounding for oral dose forms might be rationalized by taking into account the molecular descriptors of salt moiety and excipients, improved by the choice of an appropriate process of production, characterized from infrared vibrational spectroscopy and chromatographic analysis and finally predicted from accelerated stability assays.

scholarly journals Ice Coverage Induced by Depositing a Water Drop onto the Supercooled Substrate at Extreme Low Vapor Pressure

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 691
Author(s):  
Yugang Zhao ◽  
Zichao Zuo ◽  
Haibo Tang ◽  
Xin Zhang
Keyword(s):  
Vapor Pressure ◽  
Substrate Temperature ◽  
Water Drop ◽  
Industrial Processes ◽  
Aircraft Icing ◽  
Ice Coverage ◽  
Fundamental Understanding ◽  
Order Of Magnitude ◽  
The Impact ◽  
Kinetics Of

Icing/snowing/frosting is ubiquitous in nature and industrial processes, and the accretion of ice mostly leads to catastrophic consequences. The existing understanding of icing is still limited, particularly for aircraft icing, where direct observation of the freezing dynamics is inaccessible. In this work, we investigate experimentally the impact and freezing of a water drop onto the supercooled substrate at extremely low vapor pressure, to mimic an aircraft passing through clouds at a relatively high altitude, engendering icing upon collisions with pendant drops. Special attention is focused on the ice coverage induced by an impinging drop, from the perimeter pointing outward along the radial direction. We observed two freezing regimes: (I) spread-recoil-freeze at the substrate temperature of Ts = −15.4 ± 0.2 °C and (II) spread (incomplete)-freeze at the substrate temperature of Ts = −22.1 ± 0.2 °C. The ice coverage is approximately one order of magnitude larger than the frozen drop itself, and counterintuitively, larger supercooling yields smaller ice coverage in the range of interest. We attribute the variation of ice coverage to the kinetics of vapor diffusion in the two regimes. This fundamental understanding benefits the design of new anti-icing technologies for aircraft.

scholarly journals The Impact of Microclimate on the Reproductive Phenology of Female Populus tomentosa in a Micro-Scale Urban Green Space in Beijing

2021 ◽  
Vol 13 (6) ◽  
pp. 3518
Author(s):  
Xiaoyi Xing ◽  
Li Dong ◽  
Cecil Konijnendijk ◽  
Peiyao Hao ◽  
Shuxin Fan ◽  
...  
Keyword(s):  
Seed Dispersal ◽  
Spatial Variation ◽  
Air Temperature ◽  
Green Space ◽  
Populus Tomentosa ◽  
Early Spring ◽  
Reproductive Phenology ◽  
Primary Role ◽  
Micro Scale ◽  
The Impact

The spatial variation of poplars’ reproductive phenology in Beijing’s urban area has aggravated the threat of poplar fluff (cotton-like flying seeds) to public health. This research explored the impact of microclimate conditions on the reproductive phenology of female Populus tomentosa in Taoranting Park, a micro-scale green space in Beijing (range <1 km). The observed phenophases covered flowering, fruiting, and seed dispersal, and ENVI-MET was applied to simulate the effect of the microclimate on SGS (start day of the growing season). The results showed that a significant spatial variation in poplar reproductive phenology existed at the research site. The variation was significantly affected by the microclimate factors DMT (daily mean temperature) and DMH (daily mean heat transfer coefficient), with air temperature playing a primary role. Specifically, the phenology of flowering and fruiting phenophases (BBB, BF, FF, FS) was negatively correlated with DMT (−0.983 ≤ r ≤ −0.908, p <0.01) and positively correlated with DMH (0.769 ≤ r ≤ 0.864, p < 0.05). In contrast, DSD (duration of seed dispersal) showed a positive correlation with DMT (r = 0.946, p < 0.01) and a negative correlation with DMH (r = −0.922, p < 0.01). Based on the findings, the increase in air convection with lower air temperature and decrease in microclimate variation in green space can be an effective way to shorten the seed-flying duration to tackle poplar fluff pollution in Beijing’s early spring.

Microstructure and Mechanical Properties of Multi-Scale Titanium Diboride Matrix Nanocomposite Ceramic Tool Materials

2010 ◽  
Vol 431-432 ◽  
pp. 523-526
Author(s):  
Han Lian Liu ◽  
Chuan Zhen Huang ◽  
Shou Rong Xiao ◽  
Hui Wang ◽  
Ming Hong
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Transgranular Fracture ◽  
Ceramic Tool ◽  
Tool Materials ◽  
Micro Scale ◽  
Multi Scale ◽  
Nano Scale ◽  
Matrix Nanocomposite

Under the liquid-phase hot-pressing technique, the multi-scale titanium diboride matrix nanocomposite ceramic tool materials were fabricated by adding both micro-scale and nano-scale TiN particles into TiB2 with Ni and Mo as sintering aids. The effect of content of nano-scale TiN and sintering temperature on the microstructure and mechanical properties was studied. The result showed that flexural strength and fracture toughness of the composites increased first, and then decreased with an increase of the content of nano-scale TiN, while the Vickers hardness decreased with an increase of the content of nano-scale TiN. The optimal mechanical properties were flexural strength 742 MPa, fracture toughness 6.5 MPa•m1/2 and Vickers hardness 17GPa respectively. The intergranular and transgranular fracture mode were observed in the composites. The metal phase can cause ductility toughening and crack bridging, while crack deflection and transgranular fracture mode could be brought by micro-scale TiN and nano-scale TiN respectively.

scholarly journals A Static Friction Model for Unlubricated Contact of Random Rough Surfaces at Micro/Nano Scale

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 368
Author(s):  
Shengguang Zhu ◽  
Liyong Ni
Keyword(s):  
Rough Surfaces ◽  
Static Friction ◽  
Friction Model ◽  
Elastic Contact ◽  
Nano Scale ◽  
Random Rough Surfaces ◽  
Proposed Model ◽  
Dissipation Mechanism ◽  
Rigid Plane ◽  
Contact Situation

A novel static friction model for the unlubricated contact of random rough surfaces at micro/nano scale is presented. This model is based on the energy dissipation mechanism that states that changes in the potential of the surfaces in contact lead to friction. Furthermore, it employs the statistical theory of two nominally flat rough surfaces in contact, which assumes that the contact between the equivalent rough peaks and the rigid flat plane satisfies the condition of interfacial friction. Additionally, it proposes a statistical coefficient of positional correlation that represents the contact situation between the equivalent rough surface and the rigid plane. Finally, this model is compared with the static friction model established by Kogut and Etsion (KE model). The results of the proposed model agree well with those of the KE model in the fully elastic contact zone. For the calculation of dry static friction of rough surfaces in contact, previous models have mainly been based on classical contact mechanics; however, this model introduces the potential barrier theory and statistics to address this and provides a new way to calculate unlubricated friction for rough surfaces in contact.

scholarly journals The role of drop shape in impact and splash

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Qingzhe Liu ◽  
Jack Hau Yung Lo ◽  
Ye Li ◽  
Yuan Liu ◽  
Jinyu Zhao ◽  
...  
Keyword(s):  
Electromagnetic Field ◽  
Spherical Geometry ◽  
Impact Dynamics ◽  
Helmholtz Instability ◽  
Liquid Drops ◽  
Drop Shape ◽  
Spreading Dynamics ◽  
Solid Substrates ◽  
The Impact

AbstractThe impact and splash of liquid drops on solid substrates are ubiquitous in many important fields. However, previous studies have mainly focused on spherical drops while the non-spherical situations, such as raindrops, charged drops, oscillating drops, and drops affected by electromagnetic field, remain largely unexplored. Using ferrofluid, we realize various drop shapes and illustrate the fundamental role of shape in impact and splash. Experiments show that different drop shapes produce large variations in spreading dynamics, splash onset, and splash amount. However, underlying all these variations we discover universal mechanisms across various drop shapes: the impact dynamics is governed by the superellipse model, the splash onset is triggered by the Kelvin-Helmholtz instability, and the amount of splash is determined by the energy dissipation before liquid taking off. Our study generalizes the drop impact research beyond the spherical geometry, and reveals the potential of using drop shape to control impact and splash.

Sign in / Sign up

Export Citation Format

Share Document