Development of a Multiple Axis Robotic Platform for Ankle Studies

2016 ◽  
Author(s):  
Varun Nalam ◽  
Hyunglae Lee
Keyword(s):  
Degrees Of Freedom ◽  
Position Control ◽  
Sagittal Plane ◽  
Frontal Plane ◽  
Mechanical Impedance ◽  
Peak Torque ◽  
Angular Speed ◽  
Design Development ◽  
Robotic Platform ◽  
Prosthetic Devices

This paper describes the design, development, modeling, and control of a robotic platform developed for the characterization of mechanical impedance and reflex responses of the ankle in 2 degrees-of-freedom (DOF): sagittal (dorsiflexion-plantarflexion) and frontal plane (inversion-eversion). The platform, controlled actively along both DOFs, is capable of producing rapid and strong perturbations up to an angular speed of 200°/s and peak torque of 400 Nm. This enables study of ankle impedance characteristics even during extreme task conditions such as running. The platform is designed to provide perturbations to the ankle up to an angle of 20° in sagittal plane and 10° in frontal plane, which is sufficient for all possible configurations of the ankle during postural balance and stance phase of walking. These characteristics of the platform make it ideal for both impedance and reflex characterization along both DOFs of the ankle. The platform’s performance of position control is validated under varying loads simulating various conditions of posture and locomotion. The platform’s orientation accuracy in both sagittal and frontal planes is established for various input signals including slow sinusoid inputs and rapid ramp perturbations. Implications for future ankle studies to estimate neuro-mechanical characteristics and applications to assistive and prosthetic devices are discussed.

scholarly journals Biologically Inspired Design and Development of a Variable Stiffness Powered Ankle-Foot Prosthesis

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
Alexander Agboola-Dobson ◽  
Guowu Wei ◽  
Lei Ren
Keyword(s):  
Lower Limb ◽  
Degrees Of Freedom ◽  
Sagittal Plane ◽  
Frontal Plane ◽  
Variable Stiffness ◽  
Plane Motion ◽  
Biologically Inspired ◽  
Passive Rotation ◽  
Ground Conditions ◽  
Biologically Inspired Design

Recent advancements in powered lower limb prostheses have appeased several difficulties faced by lower limb amputees by using a series-elastic actuator (SEA) to provide powered sagittal plane flexion. Unfortunately, these devices are currently unable to provide both powered sagittal plane flexion and two degrees of freedom (2-DOF) at the ankle, removing the ankle’s capacity to invert/evert, thus severely limiting terrain adaption capabilities and user comfort. The developed 2-DOF ankle system in this paper allows both powered flexion in the sagittal plane and passive rotation in the frontal plane; an SEA emulates the biomechanics of the gastrocnemius and Achilles tendon for flexion while a novel universal-joint system provides the 2-DOF. Several studies were undertaken to thoroughly characterize the capabilities of the device. Under both level- and sloped-ground conditions, ankle torque and kinematic data were obtained by using force-plates and a motion capture system. The device was found to be fully capable of providing powered sagittal plane motion and torque very close to that of a biological ankle while simultaneously being able to adapt to sloped terrain by undergoing frontal plane motion, thus providing 2-DOF at the ankle. These findings demonstrate that the device presented in this paper poses radical improvements to powered prosthetic ankle-foot device (PAFD) design.

Muscle Contributions to Balance Control During Amputee and Nonamputee Stair Ascent

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Nicole G. Harper ◽  
Jason M. Wilken ◽  
Richard R. Neptune
Keyword(s):  
Angular Momentum ◽  
Lower Limb ◽  
Sagittal Plane ◽  
Balance Control ◽  
Dynamic Balance ◽  
Frontal Plane ◽  
Rate Of Change ◽  
Prosthetic Devices ◽  
Stair Ascent

Abstract Dynamic balance is controlled by lower-limb muscles and is more difficult to maintain during stair ascent compared to level walking. As a result, individuals with lower-limb amputations often have difficulty ascending stairs and are more susceptible to falls. The purpose of this study was to identify the biomechanical mechanisms used by individuals with and without amputation to control dynamic balance during stair ascent. Three-dimensional muscle-actuated forward dynamics simulations of amputee and nonamputee stair ascent were developed and contributions of individual muscles, the passive prosthesis, and gravity to the time rate of change of angular momentum were determined. The prosthesis replicated the role of nonamputee plantarflexors in the sagittal plane by contributing to forward angular momentum. The prosthesis largely replicated the role of nonamputee plantarflexors in the transverse plane but resulted in a greater change of angular momentum. In the frontal plane, the prosthesis and nonamputee plantarflexors contributed oppositely during the first half of stance while during the second half of stance, the prosthesis contributed to a much smaller extent. This resulted in altered contributions from the intact leg plantarflexors, vastii and hamstrings, and the intact and residual leg hip abductors. Therefore, prosthetic devices with altered contributions to frontal-plane angular momentum could improve balance control during amputee stair ascent and minimize necessary muscle compensations. In addition, targeted training could improve the force production magnitude and timing of muscles that regulate angular momentum to improve balance control.

scholarly journals The Spherical Inverted Pendulum: Exact Solutions of Gait and Foot Placement Estimation Based on Symbolic Computation

2021 ◽  
Vol 11 (4) ◽  
pp. 1588
Author(s):  
Giuseppe Menga
Keyword(s):  
Symbolic Computation ◽  
Degrees Of Freedom ◽  
Inverted Pendulum ◽  
Sagittal Plane ◽  
Frontal Plane ◽  
Biped Robot ◽  
Specific Form ◽  
Software Environment ◽  
Foot Placement ◽  
The Impact

The gait and the Foot Placement Estimation (FPE) has recently been extended to 3-D spaces by adopting a specific form of a spherical inverted pendulum (SIP). The approach is very attractive, as it does not involve dynamics, but it is based solely on energies and momenta, however the authors (DeHart et al.) introduced several questionable approximations, in order to reach a manageable solution. The scope of the present paper is to revisit this spherical inverted pendulum applied to biped walking, offering an exact solution to the gait and the FPE by using symbolic computation. This is facilitated by exploiting the Kane’s approach to dynamical modelling, and his software environment for symbolic manipulation, called Autolev. It generates explicit formulas describing the energies and angular momenta before/after the impact, along with the mechanics of the impact. As the resulting equations, function of (measurable) angular positions and velocities, are very compact, embedded in a numerical nonlinear solver, are suitable to be implemented in real time and used in practice to control biped robots or lower limb exoskeletons. The two main contributions of the paper are: the recovery of the balance by stepping, in the presence of a push in an arbitrary direction and omnidirectional walking. In this last respect, this specific form of SIP emphasizes the expenditure of energy in the walk. For the first time, at our knowledge, the walk of the SIP, based on energy, has been compared to the simulation of a 12 degrees of freedom biped robot tracking preview signals using the Zero Moment Point (ZMP) of the Linear Inverted Pendulum (LIPM). This quantitatively shows the inefficiency, in terms of energy, of the ZMP-based walk, and the gain due to the recovery of the collision of the flying foot. Similarity in the sagittal plane and differences in the frontal plane of the center of mass trajectories of the two approaches are shown, to open the road to an integration of fully actuated and underactuated controls, for an efficient full-dimensional robot gait to be developed in a future paper.

scholarly journals Using Biofeedback to Reduce Step Length Asymmetry Impairs Dynamic Balance in People Poststroke

2021 ◽  
pp. 154596832110193
Author(s):  
Sungwoo Park ◽  
Chang Liu ◽  
Natalia Sánchez ◽  
Julie K. Tilson ◽  
Sara J. Mulroy ◽  
...  
Keyword(s):  
Angular Momentum ◽  
Sagittal Plane ◽  
Dynamic Balance ◽  
Objective Measure ◽  
Frontal Plane ◽  
Step Length ◽  
Berg Balance Scale ◽  
Whole Body ◽  
Functional Gait ◽  
Full Body

Background People poststroke often walk with a spatiotemporally asymmetric gait, due in part to sensorimotor impairments in the paretic lower extremity. Although reducing asymmetry is a common objective of rehabilitation, the effects of improving symmetry on balance are yet to be determined. Objective We established the concurrent validity of whole-body angular momentum as a measure of balance, and we determined if reducing step length asymmetry would improve balance by decreasing whole-body angular momentum. Methods We performed clinical balance assessments and measured whole-body angular momentum during walking using a full-body marker set in a sample of 36 people with chronic stroke. We then used a biofeedback-based approach to modify step length asymmetry in a subset of 15 of these individuals who had marked asymmetry and we measured the resulting changes in whole-body angular momentum. Results When participants walked without biofeedback, whole-body angular momentum in the sagittal and frontal plane was negatively correlated with scores on the Berg Balance Scale and Functional Gait Assessment supporting the validity of whole-body angular momentum as an objective measure of dynamic balance. We also observed that when participants walked more symmetrically, their whole-body angular momentum in the sagittal plane increased rather than decreased. Conclusions Voluntary reductions of step length asymmetry in people poststroke resulted in reduced measures of dynamic balance. This is consistent with the idea that after stroke, individuals might have an implicit preference not to deviate from their natural asymmetry while walking because it could compromise their balance. Clinical Trials Number: NCT03916562.

scholarly journals Design and Calibration of a Hall Effect System for Measurement of Six-Degree-of-Freedom Motion within a Stacked Column

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3740
Author(s):  
Olafur Oddbjornsson ◽  
Panos Kloukinas ◽  
Tansu Gokce ◽  
Kate Bourne ◽  
Tony Horseman ◽  
...  
Keyword(s):  
Hall Effect ◽  
Degrees Of Freedom ◽  
Reactor Core ◽  
Degree Of Freedom ◽  
Life Extension ◽  
Scale Model ◽  
Design Development ◽  
Seismic Safety ◽  
Six Degrees Of Freedom ◽  
Six Degree Of Freedom

This paper presents the design, development and evaluation of a unique non-contact instrumentation system that can accurately measure the interface displacement between two rigid components in six degrees of freedom. The system was developed to allow measurement of the relative displacements between interfaces within a stacked column of brick-like components, with an accuracy of 0.05 mm and 0.1 degrees. The columns comprised up to 14 components, with each component being a scale model of a graphite brick within an Advanced Gas-cooled Reactor core. A set of 585 of these columns makes up the Multi Layer Array, which was designed to investigate the response of the reactor core to seismic inputs, with excitation levels up to 1 g from 0 to 100 Hz. The nature of the application required a compact and robust design capable of accurately recording fully coupled motion in all six degrees of freedom during dynamic testing. The novel design implemented 12 Hall effect sensors with a calibration procedure based on system identification techniques. The measurement uncertainty was ±0.050 mm for displacement and ±0.052 degrees for rotation, and the system can tolerate loss of data from two sensors with the uncertainly increasing to only 0.061 mm in translation and 0.088 degrees in rotation. The system has been deployed in a research programme that has enabled EDF to present seismic safety cases to the Office for Nuclear Regulation, resulting in life extension approvals for several reactors. The measurement system developed could be readily applied to other situations where the imposed level of stress at the interface causes negligible material strain, and accurate non-contact six-degree-of-freedom interface measurement is required.

scholarly journals DOES BRAIN ACTIVATION DURING FUNCTIONAL MOVEMENT TASKS DIFFERENTIATE BETWEEN GOOD AND BAD MOVERS? AN INTEGRATED NEUROIMAGING ASSESSMENT OF MOTOR CONTROL IN YOUNG ATHLETES

2021 ◽  
Vol 9 (7_suppl3) ◽  
pp. 2325967121S0013
Author(s):  
Manish Anand ◽  
Jed A. Diekfuss ◽  
Dustin R. Grooms ◽  
Alexis B. Slutsky-Ganesh ◽  
Scott Bonnette ◽  
...  
Keyword(s):  
Motor Control ◽  
Range Of Motion ◽  
Brain Function ◽  
Sagittal Plane ◽  
Brain Activity ◽  
Frontal Plane ◽  
Acl Injury ◽  
Timing Error ◽  
Lingual Gyrus ◽  
Increased Activity

Background: Aberrant frontal and sagittal plane knee motor control biomechanics contribute to increased anterior cruciate ligament (ACL) injury risk. Emergent data further indicates alterations in brain function may underlie ACL injury high risk biomechanics and primary injury. However, technical limitations have limited our ability to assess direct linkages between maladaptive biomechanics and brain function. Hypothesis/Purpose: (1) Increased frontal plane knee range of motion would associate with altered brain activity in regions important for sensorimotor control and (2) increased sagittal plane knee motor control timing error would associate with altered activity in sensorimotor control brain regions. Methods: Eighteen female high-school basketball and volleyball players (14.7 ± 1.4 years, 169.5 ± 7 cm, 65.8 ± 20.5 kg) underwent brain functional magnetic resonance imaging (fMRI) while performing a bilateral, combined hip, knee, and ankle flexion/extension movements against resistance (i.e., leg press) Figure 1(a). The participants completed this task to a reference beat of 1.2 Hz during four movement blocks of 30 seconds each interleaved in between 5 rest blocks of 30 seconds each. Concurrent frontal and sagittal plane range of motion (ROM) kinematics were measured using an MRI-compatible single camera motion capture system. Results: Increased frontal plane ROM was associated with increased brain activity in one cluster extending over the occipital fusiform gyrus and lingual gyrus ( p = .003, z > 3.1). Increased sagittal plane motor control timing error was associated with increased brain activity in multiple clusters extending over the occipital cortex (lingual gyrus), frontal cortex, and anterior cingulate cortex ( p < .001, z > 3.1); see Figure 1 (b). Conclusion: The associations of increased knee frontal plane ROM and sagittal plane timing error with increased activity in regions that integrate visuospatial information may be indicative of an increased propensity for knee injury biomechanics that are, in part, driven by reduced spatial awareness and an inability to adequately control knee abduction motion. Increased activation in these regions during movement tasks may underlie an impaired ability to control movements (i.e., less neural efficiency), leading to compromised knee positions during more complex sports scenarios. Increased activity in regions important for cognition/attention associating with motor control timing error further indicates a neurologically inefficient motor control strategy. [Figure: see text]

scholarly journals Habitual Physical Activity as a Determinant of the Effect of Moderate Physical Exercise on Postural Control in Older Men

2012 ◽  
Vol 7 (1) ◽  
pp. 58-65 ◽  
Author(s):  
Rafał Stemplewski ◽  
Janusz Maciaszek ◽  
Maciej Tomczak ◽  
Robert Szeklicki ◽  
Dorota Sadowska ◽  
...  
Keyword(s):  
Physical Activity ◽  
Postural Control ◽  
Sagittal Plane ◽  
Center Of Pressure ◽  
Force Plate ◽  
Frontal Plane ◽  
Habitual Physical Activity ◽  
Similar Reaction ◽  
Mean Velocity ◽  
Ergometer Exercise

The aim of the study was to compare the effect of exercise on postural control (PC) among the elderly with lower or higher level of habitual physical activity (HPA). The study involved 17 elderly men (mean age 72.9 ± 4.79 years). Mean velocity of the center of pressure (COP) displacements was measured using a force plate both before and after cycle ergometer exercise. A significantly higher increase in mean velocity of COP displacements and its component in the sagittal plane were observed in the group with lower level of HPA in comparison with the group with higher HPA level. Simultaneously, a relatively similar reaction to the exercise in the frontal plane was observed in both groups, possibly connected to the specific type of used exercise, which mainly activated the sagittal muscles.

Correlation between craniovertebral angle in the sagittal plane and angles and indices measured in the frontal plane at the moment of inducing forward head posture

Work ◽  
2021 ◽  
pp. 1-7
Author(s):  
Samira Molaeifar ◽  
Farzaneh Yazdani ◽  
Amin Kordi Yoosefinejad ◽  
Mohammad Taghi Karimi
Keyword(s):  
Head And Neck ◽  
Negative Correlation ◽  
Sagittal Plane ◽  
Frontal Plane ◽  
Forward Head Posture ◽  
Head Posture ◽  
Digital Devices ◽  
Moderate Negative Correlation ◽  
The Moment ◽  
Craniovertebral Angle

BACKGROUND: Forward head posture (FHP) is the most common malposition in the head and neck area. With the growing use of digital devices, the prevalence of FHP may be expected to increase dramatically. Thus far, FHP has been evaluated only in the sagittal plane. OBJECTIVE: The objective of this study was to measure angles and indices from anatomical landmarks in the frontal plane and determine the possible correlations between these variables and craniovertebral angle (CVA) as an index of FHP in the sagittal plane. METHODS: Fifty eight healthy individuals (29 men, 29 women) between 18 and 40 years old participated in this cross-sectional study. Participants were evaluated with an 8-camera motion analysis system. After markers were placed on predetermined landmarks, the participants were asked to maintain their head and neck in the neutral position for 5 seconds. Then participants induced FHP by flexing and lowering their head. The correlation between CVA and a set of angles and indices was calculated at the moment of FHP induction. RESULTS: A moderate correlation was observed between 3-D CVA and the angle formed between the sternum and both tragi for the whole sample and separately in both sexes. A moderate negative correlation was observed between 3-D CVA and height, weight, and BMI in women. A moderate negative correlation was observed between 3-D CVA and height, weight, BMI, and hours on digital devices in men. CONCLUSIONS: Changes in CVA in the sagittal plane can be predicted from changes in the angle formed between the midpoint of the sternum and the left and right tragi in the frontal plane.

scholarly journals Static Range of Motion of the First Metatarsal in the Sagittal and Frontal Planes

2018 ◽  
Vol 7 (11) ◽  
pp. 456 ◽  
Author(s):  
Sandra Tavara-Vidalón ◽  
Manuel Monge-Vera ◽  
Guillermo Lafuente-Sotillos ◽  
Gabriel Domínguez-Maldonado ◽  
Pedro Munuera-Martínez
Keyword(s):  
Range Of Motion ◽  
Least Squares Method ◽  
Sagittal Plane ◽  
Frontal Plane ◽  
Neutral Position ◽  
Future Design ◽  
First Metatarsal ◽  
Medial Cuneiform ◽  
First Ray ◽  
Degree Equation

The first metatarsal and medial cuneiform form an important functional unit in the foot, called “first ray”. The first ray normal range of motion (ROM) is difficult to quantify due to the number of joints that are involved. Several methods have previously been proposed. Controversy exists related to normal movement of the first ray frontal plane accompanying that in the sagittal plane. The objective of this study was to investigate the ROM of the first ray in the sagittal and frontal planes in normal feet. Anterior-posterior radiographs were done of the feet of 40 healthy participants with the first ray in a neutral position, maximally dorsiflexed and maximally plantarflexed. They were digitalized and the distance between the tibial malleolus and the intersesamoid crest in the three positions mentioned was measured. The rotation of the first ray in these three positions was measured. A polynomic function that fits a curve describing the movement observed in the first ray was obtained using the least squares method. ROM of the first ray in the sagittal plane was 6.47 (SD 2.59) mm of dorsiflexion and 6.12 (SD 2.55) mm of plantarflexion. ROM in the frontal plane was 2.69 (SD 4.03) degrees of inversion during the dorsiflexion and 2.97 (SD 2.72) degrees during the plantarflexion. A second-degree equation was obtained, which represents the movement of the first ray. Passive dorsiflexion and plantarflexion of the first ray were accompanied by movements in the frontal plane: 0.45 degrees of movement were produced in the frontal plane for each millimeter of displacement in the sagittal plane. These findings might be useful for the future design of instruments for clinically quantifying first ray mobility.

scholarly journals 3D kinematic analysis of patients’ gait before and after unilateral total hip replacement

2020 ◽  
Vol 22 (2) ◽  
Author(s):  
Kateřina Kolářová ◽  
Tomáš Vodička ◽  
Michal Bozděch ◽  
Martin Repko
Keyword(s):  
Range Of Motion ◽  
Total Hip Replacement ◽  
Kinematic Analysis ◽  
Hip Replacement ◽  
Sagittal Plane ◽  
Frontal Plane ◽  
Step Length ◽  
Total Hip ◽  
Before And After ◽  
Analysis System

Purpose: The purpose of the study was to describe changes in the kinematic parameters in the patients’ gait after total hip replacement. Methods: Research group of men in the end stage of osteoarthritis indicated to the THR (n = 10; age 54.1 ± 7.5 years; weight 92.2 ± 9.6 kg; height 179.7 ± 5.9 cm). All participants underwent a total of three measurements: before surgery, 3 and 6 months after the surgery. Using the 3D kinematic analysis system, the patients’ gait was recorded during each measurement session and kinematic analysis was carried out. The parameters that were monitored included the sagittal range of motion while walking in the ankle, the knee and the hip joints of the operated and the unoperated limb, and the range in the hip joint’s frontal plane, the rotation of pelvis in the frontal and transverse planes, as well as the speed of walking and the walking step length. Results: Significant increases were found in sagittal range of motion in the operated hip joint, sagittal range of motion in the ankle joint on the unoperated side and in the walking step length of the unoperated limb. Conclusions: During walking after a THR, the sagittal range of motion in the ankle of the unoperated limb increases. Also, the range of motion in the sagittal plane on the operated joint increases, which is related to the lengthening of the step of the unoperated lower limb.

Sign in / Sign up

Export Citation Format

Share Document