Analysis of a Micro Gas Turbine Fed by Natural Gas and Synthesis Gas: Test Bench and Combustor CFD Analysis

2011 ◽  
Author(s):  
M. Cadorin ◽  
M. Pinelli ◽  
A. Vaccari ◽  
R. Calabria ◽  
F. Chiariello ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Gas Turbine ◽  
Synthesis Gas ◽  
Distribution System ◽  
Biomass Conversion ◽  
Operating Conditions ◽  
Outlet Temperature ◽  
Monitoring And Control ◽  
Micro Gas Turbine ◽  
Gaseous Fuels

In recent years, the interest in the research on energy production systems fed by biofuels is increased. Gaseous fuels obtained through biomass conversion processes such as gasification, pyrolysis and pyrogasification are generally defined as synthesis gas. The use of synthesis gas in small-size energy systems, such as those used for distributed micro-cogeneration, has not yet reached a level of technological maturity that could allow a large market diffusion. For this reason, further analyses (both experimental and numerical) have to be carried out to allow these technologies to achieve performance and reliability typical of established technologies based on traditional fuels. In this paper, an experimental and numerical analysis of a combustor of a 100-kW Micro Gas Turbine fed by synthesis gas is presented. The work has been developed in the framework of a collaboration among the Department of Engineering of the University of Ferrara, the Istituto Motori CNR of Naples, and Turbec SpA of Cento (FE). The main features of the microturbine MGT Turbec T100, located at the Istituto Motori CNR of Naples, are firstly described. A decompression and distribution system allows to feed the MGT with gaseous fuels characterized by different compositions. Moreover, a system of remote monitoring and control together with a data transfer system have been developed in order to set the operative parameters of the machine for the current test. The results of the tests performed under different operating conditions are then presented. Subsequently, the paper presents the numerical analysis of a model of the MGT combustor. The combustor model is validated against manufacturer performance data and experimental data with respect to steady state performance, i.e. average outlet temperature, emission levels, pressure drops. Then, a syngas, composed by different ratios of hydrogen, carbon monoxide, methane, carbon dioxide and water, is simulated and the results analyzed.

Analysis of a Micro Gas Turbine Fed by Natural Gas and Synthesis Gas: MGT Test Bench and Combustor CFD Analysis

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
M. Cadorin ◽  
M. Pinelli ◽  
A. Vaccari ◽  
R. Calabria ◽  
F. Chiariello ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Natural Gas ◽  
Gas Turbine ◽  
Synthesis Gas ◽  
Distribution System ◽  
Operating Conditions ◽  
Outlet Temperature ◽  
Monitoring And Control ◽  
Micro Gas Turbine ◽  
Gaseous Fuels

In recent years, the interest in the research on energy production systems fed by biofuels has increased. Gaseous fuels obtained through biomass conversion processes such as gasification, pyrolysis and pyrogasification are generally defined as synthesis gas (syngas). The use of synthesis gas in small-size energy systems, such as those used for distributed micro-cogeneration, has not yet reached a level of technological maturity that could allow a large market diffusion. For this reason, further analyses (both experimental and numerical) have to be carried out to allow these technologies to achieve performance and reliability typical of established technologies based on traditional fuels. In this paper, a numerical analysis of a combustor of a 100-kW micro gas turbine fed by natural gas and biomass-derived synthesis gas is presented. The work has been developed in the framework of a collaboration between the Engineering Department of the University of Ferrara, the Istituto Motori - CNR (Napoli), and Turbec S.p A. of Corporeno di Cento (FE). The main features of the micro gas turbine Turbec T100, located at the Istituto Motori - CNR, are firstly described. A decompression and distribution system allows the feeding of the micro gas turbine with gaseous fuels characterized by different compositions. Moreover, a system of remote monitoring and control together with a data transfer system has been developed in order to set the operative parameters of the machine. The results of the tests performed under different operating conditions are then presented. Subsequently, the paper presents the numerical analysis of a model of the micro gas turbine combustor. The combustor model is validated against manufacturer performance data and experimental data with respect to steady state performance, i.e., average outlet temperature and emission levels. A sensitivity analysis on the model capability to simulate different operating conditions is then performed. The combustor model is used to simulate the combustion of a syngas, composed of different ratios of hydrogen, carbon monoxide, methane, carbon dioxide and water. The results in terms of flame displacement, temperature and emission distribution and values are analyzed and compared to the natural gas simulations. Finally, some simple modifications to the combustion chamber are proposed and simulated both with natural gas and syngas feeding.

scholarly journals A Comparative Study on Fault Detection Methods for Gas Turbine Combustion Systems

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 389
Author(s):  
Jinfu Liu ◽  
Zhenhua Long ◽  
Mingliang Bai ◽  
Linhai Zhu ◽  
Daren Yu
Keyword(s):  
Fault Detection ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Detection Methods ◽  
Distribution Model ◽  
Outlet Temperature ◽  
Combustion System ◽  
Comparison Results ◽  
Gas Turbine Combustion

As one of the core components of gas turbines, the combustion system operates in a high-temperature and high-pressure adverse environment, which makes it extremely prone to faults and catastrophic accidents. Therefore, it is necessary to monitor the combustion system to detect in a timely way whether its performance has deteriorated, to improve the safety and economy of gas turbine operation. However, the combustor outlet temperature is so high that conventional sensors cannot work in such a harsh environment for a long time. In practical application, temperature thermocouples distributed at the turbine outlet are used to monitor the exhaust gas temperature (EGT) to indirectly monitor the performance of the combustion system, but, the EGT is not only affected by faults but also influenced by many interference factors, such as ambient conditions, operating conditions, rotation and mixing of uneven hot gas, performance degradation of compressor, etc., which will reduce the sensitivity and reliability of fault detection. For this reason, many scholars have devoted themselves to the research of combustion system fault detection and proposed many excellent methods. However, few studies have compared these methods. This paper will introduce the main methods of combustion system fault detection and select current mainstream methods for analysis. And a circumferential temperature distribution model of gas turbine is established to simulate the EGT profile when a fault is coupled with interference factors, then use the simulation data to compare the detection results of selected methods. Besides, the comparison results are verified by the actual operation data of a gas turbine. Finally, through comparative research and mechanism analysis, the study points out a more suitable method for gas turbine combustion system fault detection and proposes possible development directions.

Development and Integration of the Dual Fuel Combustion System for the MGT Gas Turbine Family

2021 ◽  
Author(s):  
Bernhard Ćosić ◽  
Frank Reiss ◽  
Marc Blümer ◽  
Christian Frekers ◽  
Franklin Genin ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Distribution System ◽  
Gas Turbines ◽  
Liquid Fuel ◽  
Fuel Injection ◽  
Liquid Fuels ◽  
Dual Fuel ◽  
Gaseous Fuels ◽  
Supply And Distribution ◽  
Industrial Gas Turbines

Abstract Industrial gas turbines like the MGT6000 are often operated as power supply or as mechanical drives. In these applications, liquid fuels like 'Diesel Fuel No.2' can be used either as main fuel or as backup fuel if natural gas is not reliably available. The MAN Gas Turbines (MGT) operate with the Advanced Can Combustion (ACC) system, which is capable of ultra-low NOx emissions for gaseous fuels. This system has been further developed to provide dry dual fuel capability. In the present paper, we describe the design and detailed experimental validation process of the liquid fuel injection, and its integration into the gas turbine package. A central lance with an integrated two-stage nozzle is employed as a liquid pilot stage, enabling ignition and start-up of the engine on liquid fuel only. The pilot stage is continuously operated, whereas the bulk of the liquid fuel is injected through the premixed combustor stage. The premixed stage comprises a set of four decentralized nozzles based on fluidic oscillator atomizers, wherein atomization of the liquid fuel is achieved through self-induced oscillations. We present results illustrating the spray, hydrodynamic, and emission performance of the injectors. Extensive testing of the burner at atmospheric and full load high-pressure conditions has been performed, before verification within full engine tests. We show the design of the fuel supply and distribution system. Finally, we discuss the integration of the dual fuel system into the standard gas turbine package of the MGT6000.

Combustion Characteristics of Small Size Gas Turbine Combustor Fueled by Biomass Gas Employing Flameless Combustion

2007 ◽  
Author(s):  
Masato Hiramatsu ◽  
Yoshifumi Nakashima ◽  
Sadamasa Adachi ◽  
Yudai Yamasaki ◽  
Shigehiko Kaneko
Keyword(s):  
Gas Turbine ◽  
Combustion Efficiency ◽  
Combustion Characteristics ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Gas Turbine Combustor ◽  
Flameless Combustion ◽  
Engine Exhaust ◽  
Micro Gas Turbine

One approach to achieving 99% combustion efficiency (C.E.) and 10 ppmV or lower NOx (at 15%O2) in a micro gas turbine (MGT) combustor fueled by biomass gas at a variety of operating conditions is with the use of flameless combustion (FLC). This paper compares experimentally obtained results and CHEMKIN analysis conducted for the developed combustor. As a result, increase the number of stage of FLC combustion enlarges the MGT operation range with low-NOx emissions and high-C.E. The composition of fuel has a small effect on the characteristics of ignition in FLC. In addition, NOx in the engine exhaust is reduced by higher levels of CO2 in the fuel.

Towards Improved Prediction of Aero-Engine Combustor Performance Using Large Eddy Simulations

2008 ◽  
Author(s):  
S. James ◽  
M. S. Anand ◽  
B. Sekar
Keyword(s):  
Gas Turbine ◽  
Radial Profile ◽  
Design Tool ◽  
Operating Conditions ◽  
Outlet Temperature ◽  
Gas Turbine Combustor ◽  
Systematic Assessment ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Aero Engine

The paper presents an assessment of large eddy simulation (LES) and conventional Reynolds averaged methods (RANS) for predicting aero-engine gas turbine combustor performance. The performance characteristic that is examined in detail is the radial burner outlet temperature (BOT) or fuel-air ratio profile. Several different combustor configurations, with variations in airflows, geometries, hole patterns and operating conditions are analyzed with both LES and RANS methods. It is seen that LES consistently produces a better match to radial profile as compared to RANS. To assess the predictive capability of LES as a design tool, pretest predictions of radial profile for a combustor configuration are also presented. Overall, the work presented indicates that LES is a more accurate tool and can be used with confidence to guide combustor design. This work is the first systematic assessment of LES versus RANS on industry-relevant aero-engine gas turbine combustors.

New Concept of a Micro Gas Turbine Based Co-Generation Package for Performance Improvement in Practical Use

2005 ◽  
Author(s):  
Kenichiro Mochizuki ◽  
Satoshi Shibata ◽  
Umeo Inoue ◽  
Toshiaki Tsuchiya ◽  
Hiroko Sotouchi ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Steam Generator ◽  
Thermal Efficiency ◽  
Heat Recovery ◽  
Steam Injection ◽  
Operating Conditions ◽  
Market Potential ◽  
Injection System ◽  
Heat Recovery Steam Generator ◽  
Micro Gas Turbine

As the energy consumption has been increasing rapidly in the commercial sector in Japan, the market potential for the micro gas turbine is significant and it will be realized substantially if the thermal efficiency is improved. One of measures is to introduce the steam injection system using the steam generated by the heat recovery steam generator. Steam injection tests have been carried out using a micro gas turbine (Capstone C60). Test results showed that key performance parameters such as power output, thermal efficiency and emissions were improved by the steam injection. The stable operation of micro gas turbine with steam injection was confirmed under various operating conditions. Consequently, a micro gas turbine based co-generation package with steam injection driven by a heat recovery steam generator (HRSG) with supplementary firing is proposed.

Experimental and numerical study of flame structure and emissions in a micro gas turbine combustor

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Vedant Dwivedi ◽  
Srikanth Hari ◽  
S. M. Kumaran ◽  
B. V. S. S. S. Prasad ◽  
Vasudevan Raghavan
Keyword(s):  
Gas Turbine ◽  
Rural Areas ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
Numerical Study ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Nitric Oxides ◽  
Gas Turbine Combustor ◽  
Micro Gas Turbine

Abstract Experimental and numerical study of flame and emission characteristics in a tubular micro gas turbine combustor is reported. Micro gas turbines are used for distributed power (DP) generation using alternative fuels in rural areas. The combustion and emission characteristics from the combustor have to be studied for proper design using different fuel types. In this study methane, representing fossil natural gas, and biogas, a renewable fuel that is a mixture of methane and carbon-dioxide, are used. Primary air flow (with swirl component) and secondary aeration have been varied. Experiments have been conducted to measure the exit temperatures. Turbulent reactive flow model is used to simulate the methane and biogas flames. Numerical results are validated against the experimental data. Parametric studies to reveal the effects of primary flow, secondary flow and swirl have been conducted and results are systematically presented. An analysis of nitric-oxides emission for different fuels and operating conditions has been presented subsequently.

scholarly journals Investigation of Micro Gas Turbine Systems for High Speed Long Loiter Tactical Unmanned Air Systems

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 55 ◽  
Author(s):  
James Large ◽  
Apostolos Pesyridis
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
High Speed ◽  
Engine Performance ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Micro Gas Turbine ◽  
Fan Speed ◽  
Relative Design ◽  
Design Simplicity

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for its application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines into turbofans with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving the propulsive performance. The BMT 120 KS micro turbojet engine is selected for the performance evaluation of the conversion process using the gas turbine performance software GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis that is carried out, an improvement in the converted micro gas turbine engine performance, in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, the fan speed operation may be adjusted independently of the core, allowing an increased thrust generation or better fuel consumption. This therefore enables a wider gamut of operating conditions and enhances the performance and scope of the tactical UAV.

Micro Gas Turbine With Ceramic Nozzle and Rotor

2005 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiro Yoshida ◽  
Norihiko Iki ◽  
Takumi Ebara ◽  
Satoshi Sodeoka ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Total Power ◽  
Inlet Temperature ◽  
Present System ◽  
Outlet Temperature ◽  
Micro Gas Turbine ◽  
Buffer Material ◽  
Inconel 713C

A series of operation tests of a ceramic micro gas turbine has been successfully carried out. The baseline machine is a small single-shaft turbojet engine (J-850, Sophia Precision Corp.) with a centrifugal compressor, an annular type combustor, and a radial turbine. As a first step, an Inconel 713C alloy turbine rotor of 55 mm in diameter was replaced with a ceramic rotor (SN-235, Kyocera Corporation). A running test was conducted at rotational speeds of up to 140,000 rpm in atmospheric air. At this rotor speed, the compression pressure ratio and the thrust were 3 and 100 N, respectively. The total energy level (enthalpy and kinetic energy) of the exhaust gas jet was 240 kW. If, for example, it is assumed that 10% of the total power of the exhaust jet gas was converted into electricity, the present system would correspond to a generator with 24 kW output power. The measured turbine outlet temperature was 950°C (1,740°F) and the turbine inlet temperature was estimated to be 1,280°C (2,340°F). Although the ceramic rotor showed no evidence of degradation, the Inconel nozzle immediately in front of the turbine rotor partially melted in this rotor condition. As a second step, the Inconel turbine nozzle and casing were replaced with ceramic parts (SN-01, Ohtsuka Ceramics Inc.). The ceramic nozzle and case were supported by metal parts. Through tests with the ceramic nozzle, it became evident that one of the key technologies for the development of ceramic gas turbines is the design of the interface between the ceramic components and the metallic components, because the difference between the coefficients of linear thermal expansion of the ceramic and metal produces large thermal stress at their interface in the high-temperature condition. A buffer material made of alumina fiber was therefore introduced at the interface between the ceramic and metal.

Impact of Different Volume Sizes on Dynamic Stability of a Gas Turbine Fuel Cell Hybrid System

2019 ◽  
Author(s):  
Alessio Abrassi ◽  
Alberto Traverso ◽  
David Tucker ◽  
Eric Liese
Keyword(s):  
Fuel Cell ◽  
Gas Turbine ◽  
Cell System ◽  
Open Loop ◽  
Operating Conditions ◽  
Micro Gas Turbine ◽  
Performance Pressure ◽  
Lumped Parameter ◽  
Turbine Shaft ◽  
And Performance

Abstract A dynamic model is developed for a Micro Gas Turbine (MGT), characterized by an intrinsic free-spool configuration, coupled to large volumes. This is inspired by an experimental facility at the National Energy Technology Laboratory (NETL) called Hyper, which emulates a hybrid MGT and Fuel Cell system. The experiment and model can simulate stable and unstable operating conditions. The model is used to investigate the effects of different volumes on surge events, and to test possible strategies to safely avoid or recover from unstable compressor working conditions. The modelling approach started from the Greitzer lumped parameter approach, and it has been improved with integration of empirical methods and simulated components to better match the real Hyper plant layout and performance. Pressure, flow rate, and frequency plots are shown for the surge behavior comparing two different volume sizes, for cases where gas turbine shaft speed is uncontrolled (open loop) and controlled (closed loop). The ability to recover from a surge event is also demonstrated.

Sign in / Sign up

Export Citation Format

Share Document