Numerical Studies on the Intrusive Influence of a Five-Hole Pressure Probe in a High-Speed Axial Compressor

2017 ◽  
Author(s):  
Christoph Sanders ◽  
Marius Terstegen ◽  
Magnus Hölle ◽  
Peter Jeschke ◽  
Harald Schönenborn ◽  
...  
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
High Speed ◽  
Axial Compressor ◽  
Forced Response ◽  
Rotor Blades ◽  
Pressure Probe ◽  
Maximum Deviation ◽  
Hole Pressure ◽  
Forcing Functions

In this investigation, CFD calculations are conducted to evaluate the differences between five-hole pressure probe-determined flow quantities and the unaffected flow quantities without the probe’s intrusive influence. The blockage effect of the probe is described and evaluated. Furthermore, the influence of this effect is used to estimate the error when using measured stator outflows as forcing functions for the following rotor blades. To compare the flow field, both with and without the probe’s influence, a five-hole pressure probe is traversed numerically at midspan behind each stator row of a 2.5-stage axial compressor. For reproducing the blockage of the probe accurately, the full annulus of the respective stator row has to be modeled. In order to minimize the calculation time, a study to reduce the number of stator passages was successfully performed. To evaluate the flow quantities using the probe, a calibration polynomial is set up numerically. CFD simulations of the probe geometry within a uniform flow field for each pitch and yaw angle, as well as Mach number combination, are performed for this purpose. Moreover, the pressure probe data for the numerical traverses are corrected to account for velocity gradients in the wake region. The comparison of Mach number, with and without the probe’s influence, shows differences both in the width and the depth of the wake. The results of the Fourier-transformed wake profile for both cases are compared and changes in the first harmonic of Mach number of up to −13% identified. Finally, the first harmonic of the flow quantities is used to perform linearized CFD calculations and to evaluate the influence of disturbed forcing functions on the aerodynamic work of the following rotor blade. The average difference in aerodynamic excitation is about −12% with a maximum deviation of more than −30%. The results presented aim to draw attention to intrusive probe influences and their consequences for validating numerical results against experiments. Special attention is given to the discrepancies of forced response calculations with varying gust boundary conditions.

Experimental Investigation of Turbine Stage Flow Field and Performance at Varying Cavity Purge Rates and Operating Speeds

2016 ◽  
Author(s):  
Johan Dahlqvist ◽  
Jens Fridh
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
High Speed ◽  
Control Volume ◽  
Spatial Average ◽  
Turbine Stage ◽  
Wide Range ◽  
Annulus Flow ◽  
Purge Flow ◽  
Secondary Air

The aspect of hub cavity purge has been investigated in a high-pressure axial low-reaction turbine stage. The cavity purge is an important part of the secondary air system, used to isolate the hot main annulus flow from cavities below the hub level. A full-scale cold-flow experimental rig featuring a rotating stage was used in the investigation, quantifying main annulus flow field impact with respect to purge flow rate as it was injected upstream of the rotor. Five operating speeds were investigated of which three with respect to purge flow, namely a high loading case, the peak efficiency, and a high speed case. At each of these operating speeds, the amount of purge flow was varied across a very wide range of ejection rates. Observing the effect of the purge rate on measurement plane averaged parameters, a minor outlet swirl decrease is seen with increasing purge flow for each of the operating speeds while the Mach number is constant. The prominent effect due to purge is seen in the efficiency, showing a similar linear sensitivity to purge for the investigated speeds. An attempt is made to predict the efficiency loss with control volume analysis and entropy production. While spatial average values of swirl and Mach number are essentially unaffected by purge injection, important spanwise variations are observed and highlighted. The secondary flow structure is strengthened in the hub region, leading to a generally increased over-turning and lowered flow velocity. Meanwhile, the added volume flow through the rotor leads to higher outlet flow velocities visible in the tip region, and an associated decreased turning. A radial efficiency distribution is utilized, showing increased impact with increasing rotor speed.

Evaluation of a Flow Measurement Probe Influence on the Flow Field in High Speed Axial Compressors

2021 ◽  
Author(s):  
Ryosuke Seki ◽  
Satoshi Yamashita ◽  
Ryosuke Mito
Keyword(s):  
Flow Field ◽  
Approximation Method ◽  
High Speed ◽  
Static Pressure ◽  
Axial Compressor ◽  
Pressure Change ◽  
Operating Point ◽  
Blade Row ◽  
Probe Insertion ◽  
Probe Geometry

Abstract The aerodynamic effects of a probe for stage performance evaluation in a high-speed axial compressor are investigated. Regarding the probe measurement accuracy and its aerodynamic effects, the upstream/downstream effects on the probe and probe insertion effects are studied by using an unsteady computational fluid dynamics (CFD) analysis and by verifying in two types of multistage high-speed axial compressor measurements. The probe traverse measurements were conducted at the stator inlet and outlet in each case to evaluate blade row performance quantitatively and its flow field. In the past study, the simple approximation method was carried out which considered only the interference of the probe effect based on the reduction of the mass flow by the probe blockage for the compressor performance, but it did not agree well with the measured results. In order to correctly and quantitatively grasp the mechanism of the flow field when the probe is inserted, the unsteady calculation including the probe geometry was carried out in the present study. Unsteady calculation was performed with a probe inserted completely between the rotor and stator of a 4-stage axial compressor. Since the probe blockage and potential flow field, which mean the pressure change region induced by the probe, change the operating point of the upstream rotor and increase the work of the rotor. Compared the measurement result with probe to a kiel probe setting in the stator leading edge, the total pressure was increased about 2,000Pa at the probe tip. In addition, the developed wake by the probe interferes with the downstream stator row and locally changes the static pressure at the stator exit. To evaluate the probe insertion effect, unsteady calculations with probe at three different immersion heights at the stator downstream in an 8-stage axial compressor are performed. The static pressure value of the probe tip was increased about 3,000Pa in the hub region compared to tip region, this increase corresponds to the measurement trend. On the other hand, the measured wall static pressure showed that there is no drastic change in the radial direction. In addition, when the probe is inserted from the tip to hub region in the measurement, the blockage induced by the probe was increased. As a result, operating point of the stator was locally changed, and the rise of static pressure of the stator increased when the stator incidence changed. These typical results show that unsteady simulations including probe geometry can accurately evaluate the aerodynamic effects of probes in the high-speed axial compressor. Therefore, since the probe will pinpointed and strong affects the practically local flow field in all rotor upstream passage and stator downstream, as for the probe measurement, it is important to pay attention to design the probe diameter, the distance from the blade row, and its relative position to the downstream stator. From the above investigations, a newly simple approximation method which includes the effect of the pressure change evaluation by the probe is proposed, and it is verified in the 4-stage compressor case as an example. In this method, the effects of the distance between the rotor trailing edge (T.E.) and the probe are considered by the theory of the incompressible two-dimensional potential flow. The probe blockage decreases the mass flow rate and changes the operating point of the compressor. The verification results conducted in real compressor indicate that the correct blockage approximation enables designer to estimate aerodynamic effects of the probe correctly.

Characteristics of Stable Rotating Stall Cells in an Axial Compressor

2017 ◽  
Author(s):  
Adam R. Hickman ◽  
Scott C. Morris
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Axial Compressor ◽  
Field Measurements ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Stable Operation ◽  
Double Phase

Flow field measurements of a high-speed axial compressor are presented during pre-stall and post-stall conditions. The paper provides an analysis of measurements from a circumferential array of unsteady shroud static pressure sensors during stall cell development. At low-speed, the stall cell approached a stable size in approximately two rotor revolutions. At higher speeds, the stall cell developed within a short amount of time after stall inception, but then fluctuated in circumferential extent as the compressor transiently approached a stable post-stall operating point. The size of the stall cell was found to be related to the annulus average flow coefficient. A discussion of Phase-Locked Average (PLA) statistics on flow field measurements during stable operation is also included. In conditions where rotating stall is present, flow field measurements can be Double Phase-Locked Averaged (DPLA) using a once-per-revolution (1/Rev) pulse and the period of the stall cell. The DPLA method provides greater detail and understanding into the structure of the stall cell. DPLA data indicated that a stalled compressor annulus can be considered to contained three main regions: over-pressurized passages, stalled passages, and recovering passages. Within the over-pressured region, rotor passages exhibited increased blade loading and pressure ratio compared to pre-stall values.

Aerodynamic-Rotordynamic Interaction in Axial Compression Systems—Part I: Modeling and Analysis of Fluid-Induced Forces

2003 ◽  
Vol 125 (3) ◽  
pp. 405-415
Author(s):  
Ammar A. Al-Nahwi ◽  
James D. Paduano ◽  
Samir A. Nayfeh
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Essential Element ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Analytical Models ◽  
Modeling And Analysis ◽  
Equal Importance ◽  
Consistent Treatment

This paper presents a first principles-based model of the fluid-induced forces acting on the rotor of an axial compressor. These forces are primarily associated with the presence of a nonuniform flow field around the rotor, such as that produced by a rotor tip clearance asymmetry. Simple, analytical expressions for the forces as functions of basic flow field quantities are obtained. These expressions allow an intuitive understanding of the nature of the forces and—when combined with a rudimentary model of an axial compressor flow field (the Moore-Greitzer model)—enable computation of the forces as a function of compressor geometry, torque and pressure-rise characteristics, and operating point. The forces predicted by the model are also compared to recently published measurements and more complex analytical models, and are found to be in reasonable agreement. The model elucidates that the fluid-induced forces comprise three main contributions: fluid turning in the rotor blades, pressure distribution around the rotor, and unsteady momentum storage within the rotor. The model also confirms recent efforts in that the orientation of fluid-induced forces is locked to the flow nonuniformity, not to tip clearance asymmetry as is traditionally assumed. The turning and pressure force contributions are shown to be of comparable magnitudes—and therefore of equal importance—for operating points between the design point and the peak of the compressor characteristic. Within this operating range, both “forward” and “backward” rotor whirl tendencies are shown to be possible. This work extends recent efforts by developing a more complete, yet compact, description of fluid-induced forces in that it accounts for all relevant force contributions, both tangential and radial, that may influence the dynamics of the rotor. Hence it constitutes an essential element of a consistent treatment of rotordynamic stability under the action of fluid-induced forces, which is the subject of Part II of this paper.

Geometrical Variability Modelling of Axial Compressor Blisk Aerofoils and Evaluation of Impact on the Forced Response Problem

2020 ◽  
Author(s):  
Marco Gambitta ◽  
Arnold Kühhorn ◽  
Sven Schrape
Keyword(s):  
Computational Models ◽  
Axial Compressor ◽  
Principal Component ◽  
Forced Response ◽  
Rotor Blades ◽  
Civil Aviation ◽  
Mode Shapes ◽  
Stochastic Representation ◽  
Compressor Blades ◽  
Multiple Variable

Abstract The present work focuses on the effect of the manufacturing geometrical variability on the high-pressure compressor of a turbofan engine for civil aviation. The deviations of the geometry over the axial compressor blades are studied and modeled for the representation in the computational models. Such variability is of particular interest for the forced response problem, where small deviations of the geometry from the ideal nominal model can cause significant differences in the vibrational responses. The information regarding the geometrical mistuning is extracted from a set of manufactured components surface scans of a blade integrated disk (blisk) rotor. The optically measured geometries are parameterized, defining a set of opportune variables to describe the deviations. The dimension of the variables domain is reduced using the principal component analysis approach and a reconstruction of the modeled geometries is performed for the implementation in CFD and FEM solvers. The generated model allows a stochastic representation of the variability, providing an optimal set of variables to represent it. The aeroelastic analyses considering geometry based mistuning is carried out on a test-rig case, focusing on how such variability can affect the modal forcing generated on the blades. The force generated by the unsteady pressure field over the selected vibrational mode shapes of the rotor blades is computed through a validated CFD model. The uncertainty quantification of the geometrical variability effect on the modal forcing is performed employing Monte Carlo methods on a reduced model for the CFD solution, based on a single passage multi-blade row setup. The amplitude shift of the unsteady modal forcing is studied for different engine orders. In particular the scatter of the main engine orders forcing amplitudes for the manufactured blades can be compared with the nominal responses to predict the possible amplification due to the geometrical variability. Finally the results are compared to a full assembly computational model to assess the influence of multiple variable blades.

Active Stabilization of Rotating Stall in a Three-Stage Axial Compressor

1993 ◽  
Author(s):  
Joel M. Haynes ◽  
Gavin J. Hendricks ◽  
Alan H. Epstein
Keyword(s):  
High Speed ◽  
Travelling Waves ◽  
Axial Compressor ◽  
Open Loop ◽  
Rotating Stall ◽  
Forced Response ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Time Lags ◽  
Active Stabilization

A three-stage, low speed axial research compressor has been actively stabilized by damping low amplitude circumferentially travelling waves which can grow into rotating stall. Using a circumferential array of hot wire sensors, and an array of high speed individually positioned control vanes as the actuator, the first and second spatial harmonics of the compressor were stabilized down to a characteristic slope of 0.9, yielding an 8% increase in operating flow range. Stabilization of the third spatial harmonic did not alter the stalling flow coefficient. The actuators were also used open loop to determine the forced response behavior of the compressor. A system identification procedure applied to the forced response data then yielded the compressor transfer function. The Moore-Greitzer, 2-D, stability model was modified as suggested by the measurements to include the effect of blade row time lags on the compressor dynamics. This modified Moore-Greitzer model was then used to predict both the open and closed loop dynamic response of the compressor. The model predictions agreed closely with the experimental results. In particular, the model predicted both the mass flow at stall without control and the design parameters needed by, and the range extension realized from, active control.

Aerodynamic-Rotordynamic Interaction in Axial Compression Systems: Part I — Modeling and Analysis of Fluid-Induced Forces

2002 ◽  
Author(s):  
Ammar A. Al-Nahwi ◽  
James D. Paduano ◽  
Samir A. Nayfeh
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Essential Element ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Analytical Models ◽  
Modeling And Analysis ◽  
Equal Importance ◽  
Consistent Treatment

This paper presents a first principles-based model of the fluid-induced forces acting on the rotor of an axial compressor. These forces are primarily associated with the presence of a nonuniform flow field around the rotor, such as that produced by a rotor tip clearance asymmetry. Simple, analytical expressions for the forces as functions of basic flow field quantities are obtained. These expressions allow an intuitive understanding of the nature of the forces and—when combined with a rudimentary model of an axial compressor flow field (the Moore-Greitzer model)—enable computation of the forces as a function of compressor geometry, torque and pressure-rise characteristics, and operating point. The forces predicted by the model are also compared to recently published measurements and more complex analytical models, and are found to be in reasonable agreement. The model elucidates that the fluid-induced forces comprise three main contributions: fluid turning in the rotor blades, pressure distribution around the rotor, and unsteady momentum storage within the rotor. The model also confirms recent efforts in that the orientation of fluid-induced forces is locked to the flow nonuniformity, not to tip clearance asymmetry as is traditionally assumed. The turning and pressure force contributions are shown to be of comparable magnitudes—and therefore of equal importance—for operating points between the design point and the peak of the compressor characteristic. Within this operating range, both “forward” and “backward” rotor whirl tendencies are shown to be possible. This work extends recent efforts by developing a more complete, yet compact, description of fluid-induced forces in that it accounts for all relevant force contributions, both tangential and radial, that may influence the dynamics of the rotor. Hence it constitutes an essential element of a consistent treatment of rotordynamic stability under the action of fluid-induced forces, which is the subject of Part II of this paper.

scholarly journals Controlled-Endwall-Flow Blading for Multistage Axial Compressor Rotor

1997 ◽  
Author(s):  
M. Inoue ◽  
M. Kuroumaru ◽  
M. Furukawa ◽  
Y. Kinoue ◽  
T. Tanino ◽  
...  
Keyword(s):  
High Speed ◽  
High Efficiency ◽  
Axial Compressor ◽  
Internal Flow ◽  
Leading Edge ◽  
Rotor Blades ◽  
Advanced Technology ◽  
Low Flow ◽  
Surge Margin ◽  
Highly Loaded

This research aims to develop an advanced technology of highly loaded axial compressor stages with high efficiency and sufficient surge margin. To improve endwall boundary layer flows which lead to energy loss and instability at an operation of low flow rate, the Controlled-Endwall-Flow (CEF) rotor blades were designed and tested in the low speed rotating cascade facility of Kyushu University. The CEF rotor blades have three distinctive features: the leading-edge sweep near hub and casing wall, the leading-edge bend near the casing, and the same exit metal angle of blade evaluated by a conventional design method. Mechanical strength of the blade was verified by a numerical simulation at a high speed condition. The baseline rotor blades were designed under the same design condition and tested to compare with the CEF rotor. The results showed that the maximum stage efficiency of the CEF rotor was higher by 0.7 percent and the increase in surge margin was more than 20 percent in comparison with the baseline rotor. The results of both internal flow survey and 3D Navier-Stokes analysis showed that improvement of the overall stage performance resulted from activation of the endwall boundary layers, and suggested that further improvement might be expected by combination of end-bend stator blades and a highly loaded axial compressor stage could be developed by use of the CEF rotor.

Experimental Investigation of Aspiration in a Multi-Stage High-Speed Axial-Compressor

2016 ◽  
Author(s):  
Jan Siemann ◽  
Ingolf Krenz ◽  
Joerg R. Seume
Keyword(s):  
Flow Field ◽  
Total Pressure ◽  
High Speed ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Reference Configuration ◽  
Corner Separation ◽  
Part Load ◽  
Total Pressure Ratio ◽  
Isentropic Efficiency

Reducing the fuel consumption is a main objective in the development of modern aircraft engines. Focusing on aircraft for mid-range flight distances, a significant potential to increase the engines overall efficiency at off-design conditions exists in reducing secondary flow losses of the compressor. For this purpose, Active Flow Control (AFC) by aspiration or injection of fluid at near wall regions is a promising approach. To experimentally investigate the aerodynamic benefits of AFC by aspiration, a 4½-stage high-speed axial-compressor at the Leibniz Universitaet Hannover was equipped with one AFC stator row. The numerical design of the AFC-stator showed significant hub corner separations in the first and second stator for the reference configuration at the 80% part-load speed-line near stall. Through the application of aspiration at the first stator, the numerical simulations predict the complete suppression of the corner separation not only in the first, but also in the second stator. This leads to a relative increase in overall isentropic efficiency of 1.47% and in overall total pressure ratio of 4.16% compared to the reference configuration. To put aspiration into practice, the high-speed axial-compressor was then equipped with a secondary air system and the AFC stator row in the first stage. All experiments with AFC were performed for a relative aspiration mass flow of less than 0.5% of the main flow. Besides the part-load speed-lines of 55% and 80%, the flow field downstream of each blade row was measured at the AFC design point. Experimental results are in good agreement with the numerical predictions. The use of AFC leads to an increase in operating range at the 55% part-load speed-line of at least 19%, whereas at the 80% part-load speed-line no extension of operating range occurs. Both speed-lines, however, do show a gain in total pressure ratio and isentropic efficiency for the AFC configuration compared to the reference configuration. Compared to the AFC design point, the isentropic efficiency ηis rises by 1.45%, whereas the total pressure ratio Πtot increases by 1.47%. The analysis of local flow field data shows that the hub corner separation in the first stator is reduced by aspiration, whereas in the second stator the hub corner separation slightly increases. The application of AFC in the first stage further changes the stage loading in all downstream stages. While the first and third stage become unloaded by application of AFC, the loading in terms of the De-Haller number increases in the second and especially in the fourth stage. Furthermore, in the reference as well as in the AFC configuration, the fourth stator performs significantly better than predicted by numerical results.

Considerations for Using 3D Pneumatic Probes in High Speed Axial Compressors

2002 ◽  
Author(s):  
Simon Coldrick ◽  
Paul Ivey ◽  
Roger Wells
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Pressure Probe ◽  
Probe Type ◽  
Calibration Data ◽  
Axial Compressors ◽  
Close Proximity ◽  
Multistage Axial Compressor ◽  
Preparatory Work

This paper describes preparatory work towards three dimensional flowfield measurements downstream of the rotor in an industrial, multistage, axial compressor, using a pneumatic pressure probe. The probe is of the steady state four hole cobra probe type. The design manufacture and calibration of the probe is described. CFD calculations have been undertaken in order to assess the feasability of using such a probe in the high speed compressor environment where space is limited. This includes effects of mounting the probe in close proximity to the downstream stator blades and whether it is necessary to adjust the calibration data to compensate for these effects.

Sign in / Sign up

Export Citation Format

Share Document