Performance Desensitization for a High-Speed Axial Compressor

2018 ◽  
Author(s):  
Yassine Souleimani ◽  
Huu Duc Vo ◽  
Hong Yu
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Lower Sensitivity ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor

The increase in compressor tip clearance over the lifespan of an aero-engine leads to a long-term degradation in its fuel consumption and operating envelope. A highly promising recent numerical study on a theoretical high-speed axial compressor rotor proposed a novel casing treatment to decrease performance and stall margin sensitivity to tip clearance increase. This paper aims to apply and analyze, through CFD simulations, this casing treatment concept to a representative production axial compressor rotor with inherently lower sensitivity to tip clearance increase and complement the explanation on the mechanism behind the reduction in sensitivity. Simulations of the baseline rotor showed that the lower span region contribute as much to the pressure ratio sensitivity as the tip region which is dominated by tip leakage flow. In contrast, the efficiency sensitivity is mainly driven by losses occurring in the tip region. The novel casing treatment was successfully applied to the baseline rotor through a design refinement. Although the casing treatment causes some penalty in nominal performance, it completely reversed the pressure ratio sensitivity (i.e. pressure ratio increases with tip clearance) and reduced the efficiency sensitivity. The reversed pressure ratio sensitivity is explained by a rotation in the core flow in the lower span region indirectly induced by the flow injection from the casing treatment. The lower efficiency sensitivity comes from a reduction in the amount of fluid that crosses the tip clearance of two adjacent blades, known as double leakage. The casing treatment’s beneficial effect on stall margin sensitivity is less obvious because of the stall inception type of the baseline rotor and its change in the presence of the casing treatment.

Numerical Study on the Effects of Casing Treatment on Unsteadiness of Tip Leakage Flow in an Axial Compressor

2012 ◽  
Author(s):  
Yoojun Hwang ◽  
Shin-Hyoung Kang
Keyword(s):  
Numerical Study ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Operating Range ◽  
Compressor Rotor ◽  
Flow Through

A low speed axial compressor with casing treatment of axial slots was numerically investigated. Time-accurate numerical calculations were performed to simulate unsteady flow in the rotor tip region and the effects of casing treatment on the flow. Since the compressor rotor had a large tip clearance, it was found that the tip leakage flow had an inherent unsteady feature that was not associated with rotor rotation. The unsteadiness of the tip leakage flow was induced by changes in the blade loading due to the pressure distribution formed by the tip leakage flow. This characteristic is called rotating instability or self-induced unsteadiness. The frequency of the flow oscillation was found to decrease as the flow rate was reduced. On the other hand, as expected, the operating range was improved by casing treatment, as shown by calculations in good agreement with the experimentally measured data. The unsteadiness of the tip leakage flow was alleviated by the casing treatment. The interaction between the flow in the tip region and the re-circulated flow through the axial slots was observed in detail. The removal and injection of flow through the axial slots were responsible not only for the extension of the operating range but also for the alleviation of the unsteadiness. Analyses of instantaneous flow fields explained the mechanism of the interaction between the casing treatment and the unsteady oscillation of the tip leakage flow. Furthermore, the effects of changes in the amount of re-circulation and the location of the removal and injection flow on the unsteadiness of the tip leakage flow were examined.

Experimental and Numerical Investigation of Effect of Center Offset Degree on Compressor Stability With Circumferential Grooved Casing Treatment

2016 ◽  
Author(s):  
HaoGuang Zhang ◽  
Feng Tan ◽  
YanHui Wu ◽  
WuLi Chu ◽  
Wei Wang ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Groove Depth ◽  
Tip Clearance ◽  
Central Difference ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Blade Tip

For compressor blade tip stall, one effective way of extending stable operating range is with the application of circumferential grooved casing treatment and its validity was proved by a lot of experimental and numerical investigations. The emphases of most circumferential grooved investigations are focused on the influence of groove depth and groove number on compressor stability, and there is few investigations dealt with the center offset degree of circumferential grooves casing treatment. Hence, an axial compressor rotor with casing treatment (CT) was investigated with experimental and numerical methods to explore the effect of center offset degree on compressor stability and performance. In the work reported here, The center offset degree is defined as the ratio of the central difference between rotor tip axial chord and CT to the axial chord length of rotor tip. When the center of CT is located within the upstream direction of the center of rotor tip axial chord, the value of center offset degree is positive. The experimental and numerical results show that stall margin improvement gained with CT is reduced as the value of center offset degree varies from 0 to 0.33 or −0.33, and the CT with −0.33 center offset degree achieves the lowest value of stall margin improvement at 53% and 73% design rotational speed. The detailed analysis of the flow-field in compressor tip indicates that there is not positive effect made by grooves on leading edge of rotor blade tip when the value of center offset degree is −0.33. As the mass flow of compressor reduces further, tip clearance leakage flow results in the outlet blockage due to the absence of the positive action of grooves near blade tip tail when the value of center offset degree is 0.33. Blockage does not appear in rotor tip passage owing to utilizing the function of all grooves with CT of 0 center offset degree.

The Effects of Tip Leakage Flow on the Performance of Multistage Compressors Used in Small Core Engine Applications

2015 ◽  
Vol 138 (5) ◽  
Author(s):  
Reid A. Berdanier ◽  
Nicole L. Key
Keyword(s):  
Experimental Data ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Tip Leakage ◽  
Small Core ◽  
Thermal Growth

Large rotor tip clearances and the associated tip leakage flows are known to have a significant effect on overall compressor performance. However, detailed experimental data reflecting these effects for a multistage compressor are limited in the open literature. As design trends lead to increased overall compressor pressure ratio for thermal efficiency benefits and increased bypass ratios for propulsive benefits, the rear stages of the high-pressure compressor will become physically small. Because rotor tip clearances cannot scale exactly with blade size due to the margin needed for thermal growth considerations, relatively large tip clearances will be a reality for these rear stages. Experimental data have been collected from a three-stage axial compressor to assess performance with three-tip clearance heights representative of current and future small core machines. Trends of overall pressure rise, stall margin, and efficiency are evaluated using clearance derivatives, and the summarized data presented here begin to narrow the margin of tip clearance sensitivities outlined by previous studies in an effort to inform future compressor designs. Furthermore, interstage measurements show stage matching changes and highlight specific differences in the performance of rotor 1 and stator 2 compared to other blade rows in the machine.

Casing Treatment for Desensitization of Compressor Performance and Stability to Tip Clearance

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Mert Cevik ◽  
Huu Duc Vo ◽  
Hong Yu
Keyword(s):  
Pressure Ratio ◽  
Tip Clearance ◽  
Design Strategies ◽  
Tip Leakage Flow ◽  
Cfd Simulations ◽  
Stall Margin ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Compressor Performance ◽  
Nominal Performance

This paper presents the development of a novel casing treatment to reduce compressor performance and stall margin sensitivities to tip clearance increase. A linked research project on blade design strategies for desensitization had discovered two flow features that reduce sensitivity to tip clearance, namely increased incoming meridional momentum in the rotor tip region and reduction/elimination of double tip leakage flow. Double tip leakage flow is the flow that exits one tip clearance and enters the tip clearance of the circumferentially adjacent blade instead of convecting downstream out of the blade passage. A new and practical casing treatment was developed and analyzed through Reynolds-averaged Navier–Stokes (RANS) computational fluid dynamics (CFD) simulations to decrease double tip leakage and reduce or even eliminate performance and stall margin sensitivity to tip clearance size. The casing treatment design consists of sawtooth-shaped circumferential indentations placed on the shroud over the rotor with a depth on the order of the tip clearance size. A detailed analysis of the flow field allowed for the elucidation of the flow mechanism associated with this casing treatment. A computational parametric study gave preliminary design rules for minimizing both performance/stall margin sensitivity to tip clearance and nominal performance loss. An improved casing indentation design was produced for which CFD simulations showed a complete desensitization of pressure ratio and stall margin while reducing efficiency sensitivity significantly for the tip clearance range studied with only a very small penalty in nominal pressure ratio. Further simulations showed that this casing treatment can be combined with desensitizing blade design strategies to further reduce tip sensitivity and reduce/eliminate/reverse nominal performance penalty. Lastly, preliminary CFD simulations on an axial compressor stage indicate that this shallow indentations' casing treatment strategy remains effective in a stage environment.

scholarly journals Effect of Partial Span Aspiration on the Performance of a Transonic Axial Compressor Rotor: A Numerical Study

2015 ◽  
Vol 2015 ◽  
pp. 1-13
Author(s):  
Vijaykumar Jain ◽  
Quamber H. Nagpurwala ◽  
Abdul Nassar
Keyword(s):  
Boundary Layer ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Surface Boundary ◽  
Suction Surface ◽  
Stall Margin ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

Aspiration in an axial compressor is normally regarded as sucking out the low momentum boundary layer from blade suction surface, thus lowering the chances of flow separation and consequently that of stall under off-design operation. However, the suction mass flow does not take part in useful work and leads to loss of engine power output. This paper deals with a new concept of natural aspiration to energize blade suction surface boundary layer by injecting some fluid from pressure to suction side through a part span slot on the blade. The energized boundary layer has lesser tendency to separate, thus enhancing stall margin. Numerical simulations were carried out to study the effect of aspiration slot location and geometry on the performance and stall margin of a transonic axial compressor rotor. The computational results without aspiration slot were in fair agreement with the published experimental data. The modified rotor, with part span aspiration, showed ~3.2% improvement in stall margin at design rotational speed. The pressure ratio and efficiency of the aspirated rotor dropped by ~1.42% and ~2.0%, respectively, whereas the structural analysis did not indicate any adverse effect on the blade stress distribution in the presence of aspiration slot.

Mechanism of the Interaction Between Casing Treatment and Tip Leakage Flow in a Subsonic Axial Compressor

2006 ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yanhui Wu
Keyword(s):  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through

The use of slots and grooves in the shroud over the tips of compressor blades, known as casing treatment, is known as a powerful method to control tip leakage flow through the clearance gap and enhance the flow stability in compressors. This paper present a detailed steady and unsteady numerical studies of the coupled flow through rotor blade passages and two different types of casing treatment for a modern subsonic axial-flow compressor rotor. Particular attention was given to examining the interaction between the tip leakage flow and the casing treatment. In order to validate the multi block model applied in the rotor blade end-wall region, the computational results for the modern subsonic compressor rotor both with and without casing treatment were correlated with available experimental test data for estimation of the global performance. Detailed analyses of the flow visualization at the tip have exposed the different tip flow topologies between the cases with casing treatment and with untreated smooth wall. It was found that the primary stall margin enhancement afforded by the casing treatment is a result of the tip clearance flow manipulation. The repositioning of the tip clearance vortex further towards the trailing edge of the blade passage and delaying the movement of incoming/tip clearance flow interface to the leading edge plane are the physical mechanisms responsible for extending the compressor stall margin.

Impact of Sinusoidal Tip Gaps on Axial Compressor Rotor Performance: A Flow Field Investigation

2019 ◽  
Author(s):  
Shraman Goswami ◽  
Ashima Malhotra
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Field Investigation ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Stall Margin ◽  
Tip Leakage ◽  
Compressor Rotor

Abstract Performance of an axial compressor rotor depends largely on the tip leakage flow. Tip leakage flow results in tip leakage vortex which is a source of loss. This has an impact on the compressor efficiency as well as stall margin. A lot of work has been done to understand the tip leakage flow and controlling the same. Active and passive stall margin improvement methods mainly target the tip leakage vortex. In the current study, numerical investigations are carried out to understand flow fields near tip region of rotors. The blade tip designed to have a tip gap as sine and cosine waves (single and double waves). Numerical methodology is validated with NASA Rotor37 test results. The performance parameters of the rotors with modified tip gap shapes are compared with constant tip clearance rotor. A detailed flow field investigation is presented to compare the tip flow structure and its impact on overall performance of the compressor.

Part-Circumference Casing Treatment and the Effect on Compressor Stall

1989 ◽  
Author(s):  
N. A. Cumpsty
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Start Time ◽  
Stall Inception ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Stall Margin Improvement

Results are presented and discussed from an axial compressor rotor operated with an axial skewed slot casing treatment over part of the circumference. The compressor was one for which stall was initiated in the tip region and for this type there is some potential for stall margin improvement with lower loss using this. The main significance of the experiments is, however, the possibility of looking at aspects of stall inception. Normally stall inception is a brief transient with an unknown start time and is difficult to study but with the partial casing treatment it was possible to make the untreated section operate continuously in such a way that it underwent the processes normally leading to stall. For a tip stalling rotor the experiments identify the annulus boundary layer as the crucial region of the flow and spillage of the tip-clearance flow forward of the blades as a process leading to the rapid build up of blockage prior to instability and stall.

scholarly journals Axial Flow Compressor Stability Enhancement: Circumferential T-Shape Grooves Performance Investigation

Aerospace ◽  
2021 ◽  
Vol 8 (1) ◽  
pp. 12
Author(s):  
Marco Porro ◽  
Richard Jefferson-Loveday ◽  
Ernesto Benini
Keyword(s):  
Vortex Breakdown ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Suction Side ◽  
Treatment Technique ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement

This work focuses its attention on possibilities to enhance the stability of an axial compressor using a casing treatment technique. Circumferential grooves machined into the case are considered and their performances evaluated using three-dimensional steady state computational simulations. The effects of rectangular and new T-shape grooves on NASA Rotor 37 performances are investigated, resolving in detail the flow field near the blade tip in order to understand the stall inception delay mechanism produced by the casing treatment. First, a validation of the computational model was carried out analysing a smooth wall case without grooves. The comparisons of the total pressure ratio, total temperature ratio and adiabatic efficiency profiles with experimental data highlighted the accuracy and validity of the model. Then, the results for a rectangular groove chosen as the baseline case demonstrated that the groove interacts with the tip leakage flow, weakening the vortex breakdown and reducing the separation at the blade suction side. These effects delay stall inception, improving compressor stability. New T-shape grooves were designed keeping the volume as a constant parameter and their performances were evaluated in terms of stall margin improvement and efficiency variation. All the configurations showed a common efficiency loss near the peak condition and some of them revealed a stall margin improvement with respect to the baseline. Due to their reduced depth, these new configurations are interesting because they enable the use of a thinner light-weight compressor case as is desirable in aerospace applications.

A Proposal for Passive Wall Treatment Applied in High Performance Axial Flow Compressors

2020 ◽  
Author(s):  
Rubén Bruno Díaz ◽  
Jesuino Takachi Tomita ◽  
Cleverson Bringhenti ◽  
Francisco Carlos Elizio de Paula ◽  
Luiz Henrique Lindquist Whitacker
Keyword(s):  
Stokes Equations ◽  
Axial Compressor ◽  
Axial Flow ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Smooth Wall ◽  
Tip Leakage Flow ◽  
Viscous Effects ◽  
Stall Margin ◽  
Tip Leakage

Abstract Numerical simulations were carried out with the purpose of investigating the effect of applying circumferential grooves at axial compressor casing passive wall treatment to enhance the stall margin and change the tip leakage flow. The tip leakage flow is pointed out as one of the main contributors to stall inception in axial compressors. Hence, it is of major importance to treat appropriately the flow in this region. Circumferential grooves have shown a good performance in enhancing the stall margin in previous researches by changing the flow path in the tip clearance region. In this work, a passive wall treatment with four circumferential grooves was applied in the transonic axial compressor NASA Rotor 37. Its effect on the axial compressor performance and the flow in the tip clearance region was analyzed and set against the results attained for the smooth wall case. A 2.63% increase in the operational range of the axial compressor running at 100%N, was achieved, when compared with the original smooth wall casing configuration. The grooves installed at compressor casing, causes an increase in the flow entropy generation due to the high viscous effects in this gap region, between the rotor tip surface and casing with grooves. These viscous effects cause a drop in the turbomachine efficiency. For the grooves configurations used in this work, an efficiency drop of 0.7% was observed, compared with the original smooth wall. All the simulations were performed based on 3D turbulent flow calculations using Reynolds Averaged Navier-Stokes equations, and the flow eddy viscosity was determined using the two-equation SST turbulence model. The details of the grooves geometrical dimensions and its implementation are described in the paper.

Sign in / Sign up

Export Citation Format

Share Document