Effects of CVS Tunnel, Ambient and Instrument Dilution on Characteristics of Nano Diesel Particulate Matter Evolution

2012 ◽  
Author(s):  
Yuebin Wu ◽  
Nigel N. Clark ◽  
Daniel K. Carder
Keyword(s):  
Particle Size ◽  
Particulate Matter ◽  
Diesel Engine ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Diesel Particulate Matter ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Diesel Particulate ◽  
Exhaust Plume

In 2007, U.S. certification standards for heavy duty on-road diesel engine particulate matter (PM) emissions were reduced from 0.1g/bhp-hr to 0.01g/bhp-hr, representing an order of magnitude reduction in pollutant level. The Tier 4 standards for nonroad diesel engines, being phased in from 2008 through 2015, also require similar level of reduction in PM. Most conventional diesel engines could meet these low PM standards, once equipped with a diesel particulate filter (DPF). However, accurate, repeatable measurements of this PM may pose significant challenges. Gravimetric PM measurement involves diluting exhaust, then collecting the resultant aerosol sample on approved filter media. Few data exist to characterize the evolution of particulate matter (PM) in dilution tunnels, particularly at very low PM mass levels. Data are lacking as well, for PM evolution in portable dilution instruments and in exhaust plumes downstream of the tailpipe. Size distributions of ultra-fine particles in the diesel exhaust from a naturally aspirated ISUZU C240 diesel engine, equipped with a DPF, were studied. Particle size distribution data, during steady-state engine operations, were collected using a Cambustion DMS500 Fast Particulate Spectrometer. The effects of dilution ratios, dilution rates, and residence times on the diesel particulate matter (DPM) size distributions were analyzed and discussed. Measurements were made for three dilution methods: dilution in standard primary and secondary-dilution tunnels with a full scale Constant Volume Sampler (CVS) system, instrument dilution with a Portable Particulate Measurement Device (PPMD), and ambient dilution at the post-tailpipe exhaust plume centerline. Gaseous emissions measurements were utilized as surrogate confirmation of adequate mixing at the various measurement locations, as well as an indicator of dilution ratios. Tunnel sample results indicated varying size distributions at tunnel cross sections where the flow was still developing. Evolution of particle-size distributions was observed even for fully mixed primary flow conditions. Size distributions at the end of the secondary dilution tunnel were observed to vary with different secondary-dilution ratios. Particle-size distributions of post-tailpipe and PPMD test results were analyzed and compared with those results collected from the full-flow tunnel. Results from post-tailpipe sampling indicate that nucleation was the dominant process when the exhaust plume was diluted along the post-tailpipe centerline. Results from PPMD dilution measurements indicate that change of particle-size-distribution curves, including number count and mass concentration levels, were not as strongly correlated to dilution ratios as were the results from the other two sampling methods. This study shows that particle-size distributions measured inside full-flow dilution tunnel can adequately mimic freshly emitted exhaust sampled immediately post-tailpipe.

scholarly journals Spatial and Seasonal Variations of PM Concentration and Size Distribution in Manure-Belt Poultry Layer Houses

2019 ◽  
Vol 62 (2) ◽  
pp. 415-427 ◽  
Author(s):  
Reyna M. Knight ◽  
Xinjie Tong ◽  
Zhenyu Liu ◽  
Sewoon Hong ◽  
Lingying Zhao
Keyword(s):  
Particle Size ◽  
Particulate Matter ◽  
Size Distribution ◽  
Seasonal Variations ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Potential Health ◽  
Significant Difference ◽  
Autumn And Winter ◽  
Mass Concentrations

Abstract. Poultry layer houses are a significant source of particulate matter (PM) emissions, which potentially affect worker and animal health. Particulate matter characteristics, such as concentration and size distribution inside layer houses, are critical information for assessment of the potential health risks and development of effective PM mitigation technologies. However, this information and its spatial and seasonal variations are lacking for typical layer facilities. In this study, two TSI DustTrak monitors (DRX 8533) and an Aerodynamic Particle Sizer (APS 3321) were used to measure PM mass concentrations and number-weighted particle size distributions in two typical manure-belt poultry layer houses in Ohio in three seasons: summer, autumn, and winter. Bimodal particle size distributions were consistently observed. The average count median diameters (mean ±SD) were 1.68 ±0.25, 2.16 ±0.31, and 1.87 ±0.07 µm in summer, autumn, and winter, respectively. The average geometric standard deviations of particle size were 2.16 ±0.23, 2.16 ±0.18, and 1.74 ±0.17 in the three seasons, respectively. The average mass concentrations were 67.4 ±54.9, 289.9 ±216.2, and 428.1 ±269.9 µg m-3 for PM2.5; 73.6 ±59.5, 314.6 ±228.9, and 480.8 ±306.5 µg m-3 for PM4; and 118.8 ±99.6, 532.5 ±353.0, and 686.2 ±417.7 µg m-3 for PM10 in the three seasons, respectively. Both statistically significant (p < 0.05) and practically significant (difference of means >20% of smaller value) seasonal variations were observed. Spatial variations were only practically significant for autumn mass concentrations, likely due to external dust infiltration from nearby agricultural activities. The OSHA-mandated permissible exposure limit for respirable PM was not exceeded in any season. Keywords: Air quality, Particulate matter, Poultry housing, Seasonal variation, Spatial variation.

Determination of Particle Size Distribution of Nano-TiO2 Coating Film by AFM and Image Analysis

2010 ◽  
Vol 177 ◽  
pp. 22-24
Author(s):  
Zheng Min Li ◽  
Zhi Wei Chen ◽  
Min Tan ◽  
Ke Jing Xu ◽  
Bing Jiang
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Coating Film ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Nano Tio2 ◽  
Tio2 Particles ◽  
Atom Force Microscope

Nano-TiO2 coating film is one of the efficient photocatalysts. The particle size distribution of TiO2 has important influence on photocatalytic activity. A new method to determine the particle size distribution of TiO2 nano-film coated on ceramic was developed, by which the images of film acquired by Atom force microscope (AFM) were processed, and TiO2 particles contacted with others were separated and detected. The particle size distributions of two TiO2 nano-films were determined.

scholarly journals Factors influencing particle size distributions in finely ground forage

1994 ◽  
Vol 74 (2) ◽  
pp. 383-385 ◽  
Author(s):  
R. Soofi-Siawash ◽  
G. W. Mathison
Keyword(s):  
Particle Size ◽  
Moisture Content ◽  
Particle Size Distribution ◽  
Key Words ◽  
Size Distribution ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Routine Procedure ◽  
Factors Influencing

Two studies were conducted to assess the possibility of using particle size distribution following grinding as a routine procedure of forage evaluation. It was concluded that although differences in particle size distribution could be detected when different feeds were ground, it would be difficult to standardize the technique since particle size distributions were influenced by type of mill used for grinding, particle size of forage before grinding, and moisture content of the forage. Key words: Forages, grinding, particle size, moisture, mill

Influence of particle-size distribution homogeneity on shearing of soils subjected to internal erosion

2020 ◽  
Vol 57 (11) ◽  
pp. 1684-1694
Author(s):  
Shijin Li ◽  
Adrian R. Russell ◽  
David Muir Wood
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Soil Sample ◽  
Size Distribution ◽  
Fine Particles ◽  
Internal Erosion ◽  
Triaxial Tests ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Homogeneous Particle

Internal erosion (suffusion) is caused by water seeping through the matrix of coarse soil and progressively transporting out fine particles. The mechanical strength and stress–strain behavior of soils within water-retaining structures may be affected by internal erosion. Some researchers have set out to conduct triaxial erosion tests to study the mechanical consequences of erosion. Prior to conducting a triaxial test they subject a soil sample, which has an initially homogeneous particle-size distribution and density throughout, to erosion by causing water to enter one end of a sample and wash fine particles out the other. The erosion and movement of particles causes heterogeneous particle-size distributions to develop along the sample length. In this paper, a new soil sample formation procedure is presented that results in homogeneous particle-size distributions along the length of an eroded sample. Triaxial tests are conducted on homogeneous samples formed using the new procedure as well as heterogeneous samples created by the more commonly used approach. Results show that samples with homogeneous post-erosion particle-size distributions exhibit slightly higher peak deviator stresses than those that were heterogeneous. The results highlight the importance of ensuring homogeneity of post-erosion particle-size distributions when assessing the mechanical consequences of erosion. Forming samples using the new procedure enables the sample’s response to triaxial loading to be interpreted against a measure of its initially homogenous state.

Effect of particle size distribution of UiO-67 nano/microcrystals on the adsorption of organic dyes from aqueous solution

CrystEngComm ◽  
2018 ◽  
Vol 20 (38) ◽  
pp. 5672-5676 ◽  
Author(s):  
Run-Zhi Zhang ◽  
Yong-qing Huang ◽  
Wei Zhang ◽  
Ji-Min Yang
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Solvothermal Method ◽  
Organic Dyes ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Effect Of Particle Size

UiO-67 nano/microcrystals with different particle size distributions (PSDs) were successfully obtained by a simple solvothermal method.

Combustion Synthesis of β-SiAlON Using 3D Ball Milling

2017 ◽  
Vol 898 ◽  
pp. 1717-1723 ◽  
Author(s):  
Xue Mei Yi ◽  
Shota Suzuki ◽  
Xiong Zhang Liu ◽  
Ran Guo ◽  
Tomohiro Akiyama
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Combustion Synthesis ◽  
Ball Mill ◽  
Raw Materials ◽  
Raw Material ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Material Particle

Combustion synthesis (CS) of β-SiAlON was conducted using a 3D ball mill, with a focus on the effect of the 2D/3D ball mill premixing conditions on the CS raw material particle size as well as on the yield and grain shape of the final products. The results showed that the particle size distribution of the raw materials was significantly affected by the premixing conditions. Various particle sizes and particle size distributions could easily be obtained by using a 3D mill instead of a 2D mill due to the complex biaxial rotation movement of 3D milling. The particle size was more sensitive to the rotation ratio (vertical spin/horizontal spin, Vv/Vh) than the rotation rate when using 3D milling. Finally, β-SiAlON with less than 5 mass% unreacted Si was obtained using premix milling conditions of 135×200 [vertical spin (rpm) × horizontal spin (rpm)]. The grain shapes of the final products were clearly influenced by the particle size distribution of the raw mixtures.

Combination of 47Ti and 48Ti for the determination of highly polydisperse TiO2 particle size distributions by spICP-MS

2019 ◽  
Vol 34 (7) ◽  
pp. 1380-1386 ◽  
Author(s):  
Guillaume Bucher ◽  
François Auger
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Tio2 Particle ◽  
Size Distributions ◽  
Particle Size Distributions

Particle size distribution (PSD) of a highly polydisperse TiO2 sample determined by spICP-MS.

scholarly journals Monte Carlo simulation of coagulation in discrete particle-size distributions. Part 2. Interparticle forces and the quasi-stationary equilibrium hypothesis

1984 ◽  
Vol 143 ◽  
pp. 387-411 ◽  
Author(s):  
I. A. Valioulis ◽  
E. J. List ◽  
H. J. Pearson
Keyword(s):  
Monte Carlo Simulation ◽  
Particle Size ◽  
Monte Carlo ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Dimensional Analysis ◽  
Spherical Particles ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Coagulation Rate

Hunt (1982) and Friedlander (1960a, b) used dimensional analysis to derive expressions for the steady-state particle-size distribution in aerosols and hydrosols. Their results were supported by the Monte Carlo simulation of a non-interacting coagulating population of suspended spherical particles developed by Pearson, Valioulis & List (1984). Here the realism of the Monte Carlo simulation is improved by accounting for the modification to the coagulation rate caused by van der Waals', electrostatic and hydrodynamic forces acting between particles. The results indicate that the major hypothesis underlying the dimensional reasoning, that is, collisions between particles of similar size are most important in determining the shape of the particle size distribution, is valid only for shear-induced coagulation. It is shown that dimensional analysis cannot, in general, be used to predict equilibrium particle-size distributions, mainly because of the strong dependence of the interparticle force on the absolute and relative size of the interacting particles.

Comparison of functions for evaluating the effect of Fe and Al oxides on the particle size distribution of kaolin and quartz

Clay Minerals ◽  
1997 ◽  
Vol 32 (1) ◽  
pp. 3-11 ◽  
Author(s):  
M. Arias ◽  
E. Lopez ◽  
M. T. Barral
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Probability Density ◽  
Size Distribution ◽  
Probability Density Functions ◽  
Density Functions ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Soil Particles ◽  
Quartz Substrates

AbstractAlthough it is generally agreed that Fe and Al can act to bind soil particles, their relative efficiencies as aggregants are still disputed. In this work, the aggregating efficiencies of both aged and non-aged Fe and Al oxides precipitated on kaolin or quartz substrates were characterized by comparing their effects on particle size distributions (PSD). To facilitate comparison of PSD data, these were parameterized by fitting them with five different probability density functions (the normal, lognormal, Jaky, fractal and Rosin-Rammler functions). The best fits were given by the Rosin-Rammler function (R2 = 0.997), whose α parameter was used to compare the aggregating efficiency of Fe and Al oxides: in order of decreasing efficiency, non-aged Al > non-aged Fe ≈ aged Fe > aged Al-precipitates.

scholarly journals Particle size distributions from laboratory-scale biomass fires using fast response instruments

2010 ◽  
Vol 10 (16) ◽  
pp. 8065-8076 ◽  
Author(s):  
S. Hosseini ◽  
Q. Li ◽  
D. Cocker ◽  
D. Weise ◽  
A. Miller ◽  
...  
Keyword(s):  
United States ◽  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Geometric Mean ◽  
The United States ◽  
Biomass Combustion ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Mean Diameter

Abstract. Particle size distribution from biomass combustion is an important parameter as it affects air quality, climate modelling and health effects. To date, particle size distributions reported from prior studies vary not only due to difference in fuels but also difference in experimental conditions. This study aims to report characteristics of particle size distributions in well controlled repeatable lab scale biomass fires for southwestern United States fuels with focus on chaparral. The combustion laboratory at the United States Department of Agriculture-Forest Service's Fire Science Laboratory (USDA-FSL), Missoula, MT provided a repeatable combustion and dilution environment ideal for measurements. For a variety of fuels tested the major mode of particle size distribution was in the range of 29 to 52 nm, which is attributable to dilution of the fresh smoke. Comparing mass size distribution from FMPS and APS measurement 51–68% of particle mass was attributable to the particles ranging from 0.5 to 10 μm for PM10. Geometric mean diameter rapidly increased during flaming and gradually decreased during mixed and smoldering phase combustion. Most fuels produced a unimodal distribution during flaming phase and strong biomodal distribution during smoldering phase. The mode of combustion (flaming, mixed and smoldering) could be better distinguished using the slopes in MCE (Modified Combustion Efficiency) vs. geometric mean diameter than only using MCE values.

Sign in / Sign up

Export Citation Format

Share Document