Modelling of Soot Formation and Experimental Study for Different Octane Number Fuels in Dual Fuel Combustion Engine With Diesel

2020 ◽  
Author(s):  
M. Krishnamoorthi ◽  
S. Sreedhara ◽  
Pavan Prakash Duvvuri
Keyword(s):  
Particle Size ◽  
Soot Formation ◽  
Combustion Engine ◽  
Combustion Process ◽  
Dual Fuel ◽  
Nox Emissions ◽  
Low Temperature Combustion ◽  
Oxides Of Nitrogen ◽  
Condensation Mode ◽  
Test Engine

Abstract This work investigates the effects of low reactivity fuel (LRF) on reactivity controlled compression ignition (RCCI) engine with fossil diesel. RCCI mode of combustion is a low temperature combustion (LTC) strategy which reduces both oxides of nitrogen (NOx) and soot emissions simultaneously. Syngas and methanol can be obtained from renewable biological resources and conventional coal. LRF (methanol, syngas and gasoline) has been supplied to the engine along with intake air and diesel is injected to initiate the combustion process. Test engine has been operated for different dual fuel modes at constant engine speed (1500 rpm) and load (80%). Closed cycle combustion simulations have been performed to complement the experimental results and in-cylinder dynamics. Particle size mimic (PSM) model has been used to investigate the soot particle number and mass-size distributions and mean particle size. Results confirmed that maximum gross indicated thermal efficiency (38%) has been observed in gasoline/diesel dual fuel mode. Compared to gasoline/diesel dual fuel mode, about 74% and 86%, lower soot and NOx emissions have been observed for methanol/diesel dual fuel mode, while about 46% and 52% lower soot and NOx emissions have been found in syngas/diesel mode. About 53% higher carbon monoxide emission has been observed for syngas/diesel case as compared to gasoline/diesel case. Predictions from soot modelling reveal that condensation mode, surface growth mode and nucleation mode particles are dominant in methanol, syngas and gasoline/diesel dual fuel modes respectively. Bigger primary soot particles (diameter > 35 nm, nanometre) have been observed for methanol/diesel mode and the gasoline/diesel mode shows a smaller size of primary particles.

Effects of Intake Port Optimization on Soot Emission from Diesel Engine

2014 ◽  
Vol 535 ◽  
pp. 333-339
Author(s):  
Yue Chen ◽  
Lin Lv ◽  
Jie Shen
Keyword(s):  
Standard Deviation ◽  
Soot Formation ◽  
Combustion Engine ◽  
Double Helix ◽  
Direct Injection ◽  
Combustion Process ◽  
Flow Coefficient ◽  
Swirl Ratio ◽  
Characteristic Parameters ◽  
Double Tangent

All future engine developments must consider the primary task of achieving the required emission levels. An important step towards the development of combustion engines is the optimization of the flow in the intake ports. The charging movement in the combustion chamber, which is generated by the intake flow, considerably influences the quality of the combustion engine. In this paper, steady CFD analysis were applied to different structures of double-tangent-port. The swirl ratio can be improved while flow coefficient remains unchanged if port eccentricity is 34.4 mm. By defining three characteristic parameters, the speed non-uniformity index, standard deviation and mixture concentration standard deviation and equivalent ratio range, quantitatively describing the combustion process in cylinder, and then compared with transient CFD three-dimensional contours, we can see that characteristic parameters can be more accurate and comprehensive in analyzing the influence of inlet structure of soot formation. Effects of different intake ports on fuel-air mixing in a turbocharged diesel direct injection engine during intake and compression strokes are analyzed. It turns out that the optimized double-tangent-port has the highest uniformity of velocity, in the meanwhile, air/fuel mixing is relatively uniform. On the other hand, mixed-port and double-helix-port can cause uneven flow field which is bad for combustion, even though the swirl ratio can increase largely. Finally, the simulation results show that soot emissions of the optimized double-tangent-port have significantly lower levels, at 2200 r/min under full load.

scholarly journals An Experimental Study on the Performance and Emission of the diesel/CNG Dual-Fuel Combustion Mode in a Stationary CI Engine

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3857 ◽  
Author(s):  
Arkadiusz Jamrozik ◽  
Wojciech Tutak ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Fuel ◽  
Carbon Dioxide Emissions ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Stable Operation ◽  
Performance And Emission ◽  
Ci Engine

One of the possibilities to reduce diesel fuel consumption and at the same time reduce the emission of diesel engines, is the use of alternative gaseous fuels, so far most commonly used to power spark ignition engines. The presented work concerns experimental research of a dual-fuel compression-ignition (CI) engine in which diesel fuel was co-combusted with CNG (compressed natural gas). The energy share of CNG gas was varied from 0% to 95%. The study showed that increasing the share of CNG co-combusted with diesel in the CI engine increases the ignition delay of the combustible mixture and shortens the overall duration of combustion. For CNG gas shares from 0% to 45%, due to the intensification of the combustion process, it causes an increase in the maximum pressure in the cylinder, an increase in the rate of heat release and an increase in pressure rise rate. The most stable operation, similar to a conventional engine, was characterized by a diesel co-combustion engine with 30% and 45% shares of CNG gas. Increasing the CNG share from 0% to 90% increases the nitric oxide emissions of a dual-fuel engine. Compared to diesel fuel supply, co-combustion of this fuel with 30% and 45% CNG energy shares contributes to the reduction of hydrocarbon (HC) emissions, which increases after exceeding these values. Increasing the share of CNG gas co-combusted with diesel fuel, compared to the combustion of diesel fuel, reduces carbon dioxide emissions, and almost completely reduces carbon monoxide in the exhaust gas of a dual-fuel engine.

Low Cetane Fuels in Compression Ignition Engine to Achieve LTC

2011 ◽  
Author(s):  
Swami Nathan Subramanian ◽  
Stephen Ciatti
Keyword(s):  
Low Temperature ◽  
Internal Combustion Engines ◽  
High Efficiency ◽  
Fuel Efficiency ◽  
Nox Emissions ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Oxides Of Nitrogen ◽  
Compression Ignition Engine ◽  
Conventional Combustion

The conventional combustion processes of Spark Ignition (SI) and Compression Ignition (CI) have their respective merits and demerits. Internal combustion engines use certain fuels to utilize those conventional combustion technologies. High octane fuels are required to operate the engine in SI mode, while high cetane fuels are preferable for CI mode of operation. Those conventional combustion techniques struggle to meet the current emissions norms while retaining high efficiency. In particular, oxides of nitrogen (NOx) and particulate matter (PM) emissions have limited the utilization of diesel fuel in compression ignition engines, and conventional gasoline operated SI engines are not fuel efficient. Advanced combustion concepts have shown the potential to combine fuel efficiency and improved emissions performance. Low Temperature Combustion (LTC) offers reduced NOx and PM emissions with comparable modern diesel engine efficiencies. The ability of premixed, low-temperature compression ignition to deliver low PM and NOx emissions is dependent on achieving optimal combustion phasing. Variations in injection pressures, injection schemes and Exhaust Gas Recirculation (EGR) are studied with low octane gasoline LTC. Reductions in emissions are a function of combustion phasing and local equivalence ratio. Engine speed, load, EGR quantity, compression ratio and fuel octane number are all factors that influence combustion phasing. Low cetane fuels have shown comparable diesel efficiencies with low NOx emissions at reasonably high power densities.

Application of Dynamic ϕ–T Map: Analysis on a Natural Gas/Diesel Fueled RCCI Engine

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Jing Li ◽  
Wenming Yang ◽  
Hui An ◽  
Dezhi Zhou ◽  
Markus Kraft
Keyword(s):  
Natural Gas ◽  
Soot Formation ◽  
Combustion Process ◽  
Diesel Oil ◽  
Chemical Mechanism ◽  
Low Temperature Combustion ◽  
Injection Duration ◽  
Start Of Injection ◽  
Temperature Combustion ◽  
Map Analysis

In this study, dynamic ϕ–T map analysis was applied to a reactivity controlled compression ignition (RCCI) engine fueled with natural gas (NG) and diesel. The combustion process of the engine was simulated by coupled kiva4-chemkin with a diesel oil surrogate (DOS) chemical mechanism. The ϕ–T maps were constructed by the mole fractions of soot and NO obtained from senkin and ϕ–T conditions from engine simulations. Five parameters, namely, NG fraction, first start of injection (SOI) timing, second SOI timing, second injection duration, and exhaust gas recirculation (EGR) rate, were varied in certain ranges individually, and the ϕ–T maps were compared and analyzed under various conditions. The results revealed how the five parameters would shift the ϕ–T conditions and influence the soot–NO contour. Among the factors, EGR rate could limit the highest temperature due to its dilute effect, hence maintaining RCCI combustion within low-temperature combustion (LTC) region. The second significant parameter is the premixed NG fraction. It could set the lowest temperature; moreover, the tendency of soot formation can be mitigated due to the lessened fuel impingement and the absence of C–C bond. Finally, the region of RCCI combustion was added to the commonly known ϕ–T map diagram.

The role of the diffusion-limited injection in direct dual fuel stratification

2016 ◽  
Vol 18 (4) ◽  
pp. 351-365 ◽  
Author(s):  
Martin Wissink ◽  
Rolf Reitz
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Thermal Efficiency ◽  
Soot Formation ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Low Temperature Combustion ◽  
Fuel Stratification ◽  
Diffusion Limited ◽  
Temperature Combustion

Low-temperature combustion offers an attractive combination of high thermal efficiency and low NO x and soot formation at moderate engine load. However, the kinetically-controlled nature of low-temperature combustion yields little authority over the rate of heat release, resulting in a tradeoff between load, noise, and thermal efficiency. While several single-fuel strategies have achieved full-load operation through the use of equivalence ratio stratification, they uniformly require retarded combustion phasing to maintain reasonable noise levels, which comes at the expense of thermal efficiency and combustion stability. Previous work has shown that control over heat release can be greatly improved by combining reactivity stratification in the premixed charge with a diffusion-limited injection that occurs after low-temperature heat release, in a strategy called direct dual fuel stratification. While the previous work has shown how the heat release control offered by direct dual fuel stratification differs from other strategies and how it is enabled by the reactivity stratification created by using two fuels, this paper investigates the effects of the diffusion-limited injection. In particular, the influence of fuel selection and the pressure, timing, and duration of the diffusion-limited injection are examined. Diffusion-limited injection fuel type had a large impact on soot formation, but no appreciable effect on performance or other emissions. Increasing injection pressure was observed to decrease filter smoke number exponentially while improving combustion efficiency. The timing and duration of the diffusion-limited injection offered precise control over the heat release event, but the operating space was limited by a tradeoff between NO x and soot.

scholarly journals An analysis of EGR impact on combustion process in the SI test engine

2012 ◽  
Vol 148 (1) ◽  
pp. 11-16
Author(s):  
Wojciech TUTAK
Keyword(s):  
Ignition Delay ◽  
Thermal Cycle ◽  
Combustion Engine ◽  
Combustion Process ◽  
Exhaust Gas ◽  
No Emission ◽  
Combustion Duration ◽  
Test Engine ◽  
Gas Recirculation ◽  
The Impact

The results of modelling of thermal cycle of spark ignition internal combustion engine with exhaust gas recirculation are presented. Results of the impact of EGR on the ignition delay and the combustion duration are presented. The optimization of thermal cycle was carried out in terms of ignition advance angle in order to obtain the possible highest value of efficiency and the least NO emission. The results indicated a significant impact of EGR on the ignition delay and combustion duration.

Modeling and control of fuel distribution in a dual-fuel internal combustion engine leveraging late intake valve closings

2016 ◽  
Vol 18 (8) ◽  
pp. 797-809 ◽  
Author(s):  
Mateos Kassa ◽  
Carrie Hall ◽  
Andrew Ickes ◽  
Thomas Wallner
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Internal Combustion ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Intake Valve ◽  
Fuel Distribution ◽  
Gas Recirculation

In internal combustion engines, cycle-to-cycle and cylinder-to-cylinder variations of the combustion process have been shown to negatively impact the fuel efficiency of the engine and lead to higher exhaust emissions. The combustion variations are generally tied to differences in the composition and condition of the trapped mass throughout each cycle and across individual cylinders. Thus, advanced engines featuring exhaust gas recirculation, flexible valve actuation systems, advanced fueling strategies, and turbocharging systems are prone to exhibit higher variations in the combustion process. In this study, the cylinder-to-cylinder variations of the combustion process in a dual-fuel internal combustion engine leveraging late intake valve closing are investigated and a model to predict and address one of the root causes for these variations across cylinders is developed. The study is conducted on an inline six-cylinder heavy-duty dual-fuel engine equipped with exhaust gas recirculation, a variable geometry turbocharger, and a fully flexible variable intake valve actuation system. The engine is operated with late intake valve closure timings in a dual-fuel combustion mode in which a high reactivity fuel is directly injected into the cylinders and a low reactivity fuel is port injected into the cylinders. The cylinder-to-cylinder variations observed in the study have been associated with the maldistribution of the port-injected fuel, which is exacerbated at late intake valve timings. The resulting difference in indicated mean effective pressure between the cylinders ranges from 9% at an intake valve closing of 570° after top dead center to 38% at an intake valve closing of 620° after top dead center and indicates an increasingly uneven fuel distribution. The study leverages both experimental and simulation studies to investigate the distribution of the port-injected fuel and its impact on cylinder-to-cylinder variation. The effects of intake valve closing as well as the impact of intake runner length on fuel distribution were quantitatively analyzed, and a model was developed that can be used to accurately predict the fuel distribution of the port-injected fuel at different operating conditions with an average estimation error of 1.5% in cylinder-specific fuel flow. A model-based control strategy is implemented to adjust the fueling at each port and shown to significantly reduce the cylinder-to-cylinder variations in fuel distribution.

An Experimental Investigation on the Effect of Post-Injection Strategies on Combustion and Emissions in the Low-Temperature Diesel Combustion Regime

2005 ◽  
Vol 129 (1) ◽  
pp. 279-286 ◽  
Author(s):  
Hanho Yun ◽  
Rolf D. Reitz
Keyword(s):  
Low Temperature ◽  
Soot Formation ◽  
Combustion Regime ◽  
Nox Emissions ◽  
Diesel Combustion ◽  
Low Temperature Combustion ◽  
Post Injection ◽  
Temperature Combustion ◽  
Soot Emissions ◽  
Injection Strategies

In order to meet future emissions regulations, new combustion concepts are being developed. Among them, the development of low-temperature diesel combustion systems has received considerable attention. Low NOx emissions are achieved through minimization of peak temperatures during the combustion process. Concurrently, soot formation is inhibited due to a combination of low combustion temperatures and extensive fuel-air premixing. In this study, the effect of late-cycle mixing enhancement by post-injection strategies on combustion and engine-out emissions in the low-temperature (low soot and NOx emissions) combustion regime was experimentally investigated. The baseline operating condition considered for low-temperature combustion was 1500rpm, 3bar IMEP with 50% EGR rate, and extension to high loads was considered by means of post injection. Post-injection strategies gave very favorable emission results in the low-temperature combustion regime at all loads tested in this study. Since post injection leads to late-cycle mixing improvement, further reductions in soot emissions were achieved without deteriorating the NOx emissions. With smaller fuel injected amounts for the second pulse, better soot emissions were found. However, the determination of the dwell between the injections was found to be very important for the emissions.

Sign in / Sign up

Export Citation Format

Share Document