Assessment of engineering properties of Bangkok clay

2007 ◽  
Vol 44 (2) ◽  
pp. 173-187 ◽  
Author(s):  
Suksun Horpibulsuk ◽  
Satoru Shibuya ◽  
Kittitep Fuenkajorn ◽  
Wanchai Katkan
Keyword(s):  
Shear Strength ◽  
Yield Stress ◽  
Void Ratio ◽  
State Parameter ◽  
Liquid Limit ◽  
Vertical Stress ◽  
Engineering Properties ◽  
Ideal Condition ◽  
Intrinsic State ◽  
Yield State

Due to the effect of structure, Bangkok clay is stable in a metastable state. Its void ratio, e, is the summation of the void ratio sustained by the intrinsic fabric, eR, and the additional void ratio due to the structure, es. The intrinsic state line (eR versus log σ′v, where σ′v is the effective vertical stress) is developed in terms of the void ratio at the liquid limit, eL. At the post-yield state, es is inversely proportional to σ′v. The residual additional void ratio, esr, which cannot be eliminated by the increase in effective vertical stress, is constant at about 0.20 for soft Bangkok clay and 0.12 for medium stiff Bangkok clay. From these findings and the ideal condition of zero compression at the pre-yield state, the field yield stress and field compression curve can be assessed. The undrained shear strength is directly related to the field yield stress, since both reflect the structure. The soil structure does not significantly influence the permeability. The permeability of the clay in structured and destructured states is identical under the same void ratio and can be determined from the generalized state parameter, e/eL. These observations result in a simple and practical method for assessment of the engineering properties of natural Bangkok clay.Key words: Bangkok clay, destructured state, compression, intrinsic state line, permeability, structured state, vane shear strength.

scholarly journals Geotechnical Properties of Soft Marine Soil at Chan May Port, Vietnam

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Thi Nu NGUYEN ◽  
Thanh Duong NGUYEN ◽  
Truong Son BUI
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Void Ratio ◽  
Soft Soil ◽  
Field Investigation ◽  
Liquid Limit ◽  
Geotechnical Properties ◽  
Unit Weight ◽  
Dry Unit Weight ◽  
Marine Soil

Soft marine soil deposit is distributed under the sea with many special properties. This type ofsoil is rarely researched in Vietnam because of the difficult geotechnical investigation under the sea level.In this paper, the experimental laboratories were performed to investigate the geotechnical properties ofsoft marine soil at Chan May port, Vietnam. The field investigation results indicate that the thickness ofsoft soil varies from a few meters to more than ten meters. Soft soil has a high value of water content,void ratio, and compressibility and a low value of shear strength. The compression index has a goodrelationship with water content, liquid limit, and dry unit weight. The unit weight, shear strength, and preconsolidationpressure increase with the increase of depth. These results show that the soil in the studyarea is unfavorable for construction activities.

Geological and soil engineering properties of shallow landslides occurring in the Kutupalong Rohingya Camp in Cox’s Bazar, Bangladesh

Landslides ◽  
2022 ◽  
Author(s):  
A. S. M. Maksud Kamal ◽  
Farhad Hossain ◽  
Md. Zillur Rahman ◽  
Bayes Ahmed ◽  
Peter Sammonds
Keyword(s):  
Shear Strength ◽  
Bulk Density ◽  
Mineralogical Composition ◽  
Fine Sand ◽  
Liquid Limit ◽  
Engineering Properties ◽  
Anthropogenic Factors ◽  
Residual Soil ◽  
Geological Condition ◽  
Residual Soils

AbstractThe Forcibly Displaced Myanmar Nationals (FDMN), historically known as ‘Rohingya’ who fled the 2017 ethnic atrocities and genocide in the Northern Rakhine State of Myanmar, took shelter in Cox’s Bazar District of Bangladesh. The camp network, known as Kutupalong Rohingya Camp (KRC), is situated in the tectonically active tertiary hilly terrain. The KRC has been experiencing hydrometeorological hazards, where landslides are frequent. This study investigated the slopes’ geological condition, engineering properties and human interventions, which influence the landslides. The exposed slopes were relatively high (> 10 m) and steep ranging from 40° to 60° that have numerous polygonal tension cracks and fissures. From the geological and geotechnical aspects, there are three successive units of slope materials: (1) residual soils of sandy silt with clay, (2) highly weathered silty sandstones and (3) shale/clay with silt and fine sand intercalations at the bottom of the slopes. Field observations revealed that most slope failures occurred in the residual soil and weathered silty sandstone units. The residual soils have a bulk density of 1.49–1.97 g/cm3, a liquid limit of 25–48%, a plasticity index of 5–16% and an undrained shear strength of 23–46 kPa. The silty sandstones have a bulk density of 1.44–1.94 g/cm3, an internal friction angle of 34°–40° and a cohesion of 0.5–13 kPa. The mineralogical composition determined by the X-ray diffraction shows low clay mineral content, which does not affect landslides. However, the slope geometry, low shear strength with strain softening properties and torrential rainfall accompanied by anthropogenic factors cause numerous landslides every year. This study will help take proper mitigation and preparedness measures for slope protection in the KRC area and surroundings.

A reexamination of the permeability index of clays

1993 ◽  
Vol 30 (1) ◽  
pp. 187-191 ◽  
Author(s):  
G. L. Sivakumar Babu ◽  
N. S. Pandian ◽  
T. S. Nagaraj
Keyword(s):  
Void Ratio ◽  
State Parameter ◽  
Paper Analysis ◽  
Liquid Limit ◽  
Test Results ◽  
Permeability Index ◽  
Initial Void Ratio ◽  
Generalized State ◽  
Marine Clays ◽  
Parameter Approach

The permeability index Ck, similar to the compression index, is the slope of the void ratio – coefficient of permeability relationship. Literature shows that, in general, for sensitive clays it can be related to initial void ratio by Ck = 0.5e0. The possibility of obtaining such a relationship for Cochin marine clays in terms of liquid limit void ratio is indicated in this paper. Analysis of permeability behaviour of Cochin marine clays and the test results available in published literature using generalized state parameter approach show that, in principle, these forms of equations for the permeability index are tenable, even though they were obtained based on experimental observation alone. Key words : permeability index, initial void ratio, void ratio at liquid limit, generalized state parameter approach.

Experimental Study on Temperature Effect on Engineering Properties of Clayey Soils

2012 ◽  
Vol 512-515 ◽  
pp. 1905-1918
Author(s):  
Yu Xian Shao ◽  
Bin Shi ◽  
Chun Liu ◽  
Lei Gao
Keyword(s):  
Shear Strength ◽  
Temperature Effect ◽  
Water Content ◽  
Free Water ◽  
Adsorbed Water ◽  
Liquid Limit ◽  
Engineering Properties ◽  
Dry Density ◽  
Clayey Soils ◽  
Increasing Temperature

Temperature significantly influences the engineering properties of clayey soil and this temperature effect usually depends on soil type. In this investigation, laboratorial experiments were conducted on three soils to evaluate the adsorbed water content, Atterberg limits, swelling, shear strength and permeability under different temperatures (5-50°C). The results indicate that liquid limit decreases, swelling increases, permeability increases with increasing temperature. It is fundamentally due to the change of adsorbed water content. Hydrophilic minerals, which contain large amounts of adsorbed water, play an important role in the temperature effect. With the increase of hydrophilic minerals, the temperature effect on liquid limit increases and the effect on swelling ratio decreases. The hydrophilic minerals content also has significant impact on the temperature effect of permeability. With increasing temperature, the adsorbed water is transformed to free water, and then the permeability may increase significantly. The shear strength of clayey soils with higher content of hydrophilic mineral is more sensitive to temperature variation. The cohesive force mainly changes linearly with the temperature. Different phenomena, i.e. thermal-hardening or thermal-softening, was observed on strength behaviour due to different hydrophilic mineral content, moisture content and dry density of sample.

Characterization of pond ash-bentonite mixes as landfill liner material

2020 ◽  
Vol 38 (12) ◽  
pp. 1420-1428
Author(s):  
Suryaleen Rout ◽  
Suresh Prasad Singh
Keyword(s):  
Hydraulic Conductivity ◽  
Void Ratio ◽  
Liquid Limit ◽  
Engineering Properties ◽  
Basic Material ◽  
Shape Parameters ◽  
Liner Material ◽  
Pond Ash ◽  
Landfill Liner

Characterization of pond ash-bentonite mixes is made to assess their suitability as liner material for waste disposal facilities by examining the relevant index and engineering properties. Further, a comparative assessment is made between sand-bentonite and pond ash-bentonite mixes for the range of bentonite content varying from 0 to 30% by weight at an interval of 5% to ensure an effective substitution of sand with pond ash. Addition of bentonite to sand or pond ash significantly influences the plasticity, strength and permeability properties. Besides, the shape parameters of the coarser fraction and morphology of compacted mixes also influence the engineering properties. A multiple linear regression equation is suggested to predict the hydraulic conductivity of these mixes by considering the basic material properties such as liquid limit, plasticity index and void ratio as an input variable with a correlation coefficient of 0.92 between the measured and predicted hydraulic conductivity values. At comparable conditions, compacted pond ash-bentonite mixes exhibit higher strength but also higher permeability than sand-bentonite mixes. Pond ash-bentonite and sand-bentonite mixes met the liner requirements when compacted with modified Proctor compaction effort at a minimum bentonite content of 20% and 15%, respectively.

scholarly journals Mechanical Properties and Micro Mechanism of Nano-Clay-Modified Soil Cement Reinforced by Recycled Sand

2021 ◽  
Vol 13 (14) ◽  
pp. 7758
Author(s):  
Biao Qian ◽  
Wenjie Yu ◽  
Beifeng Lv ◽  
Haibo Kang ◽  
Longxin Shu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Soil Mass ◽  
Direct Shear ◽  
Test Results ◽  
The Sustainable Development ◽  
Direct Shear Tests ◽  
Soil Cement ◽  
Nano Clay ◽  
New Material

To observe the effect of recycled sand and nano-clay on the improvement of the early strength of soil-cement (7d), 0%, 10%, 15% and 20% recycled sand were added. While maintaining a fixed moisture content of 30%, the ratios of each material are specified in terms of soil mass percentage. The shear strength of CSR (recycled sand blended soil-cement) was investigated by direct shear test and four groups of specimens (CSR-1, CSR-2, CSR-3 and CSR-4) were obtained. In addition, 8% nano-clay was added to four CSR groups to obtain the four groups of CSRN-1, CSRN-2, CSRN-3 and CSRN-4 (soil-cement mixed with recycled sand and nano-clay), which were also subjected to direct shear tests. A detailed analysis of the modification mechanism of soil-cement by recycled sand and nano-clay was carried out in combination with scanning electron microscopy (SEM) and IPP (ImagePro-Plus) software. The test results showed that: (1) CSR-3 has the highest shear strength due to the “concrete-like” effect of the incorporation of recycled sand. With the addition of 8% nano-clay, the overall shear strength of the cement was improved, with CSRN-2 having the best shear strength, thanks to the filling effect of the nano-clay and its high volcanic ash content. (2) When recycled sand and nano-clay were added to soil-cement, the improvement in shear strength was manifested in a more reasonable macroscopic internal structure distribution of soil-cement. (3) SEM test results showed that the shear strength was negatively correlated with the void ratio of its microstructure. The smaller the void ratio, the greater the shear strength. This shows that the use of reclaimed sand can improve the sustainable development of the environment, and at the same time, the new material of nano-clay has potential application value.

scholarly journals Experimental Study on Improvement of Marine Soft Soil with Alkali Residue

2018 ◽  
Vol 53 ◽  
pp. 04021
Author(s):  
SHAO Yong ◽  
LIU Xiao-li ◽  
ZHU Jin-jun
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Soft Soil ◽  
Compressive Modulus ◽  
Engineering Properties ◽  
Test Results ◽  
Use Of Resources ◽  
One Year

Industrial alkali slag is the discharge waste in the process of alkali production. About one million tons of alkali slag is discharged in China in one year. It is a burden on the environment, whether it is directly stacked or discharged into the sea. If we can realize the use of resources, it is a multi-pronged move, so alkali slag is used to improve solidified marine soft soil in this paper. The test results show that the alkali residue can effectively improve the engineering properties of marine soft soil. Among them, the unconfined compressive strength and compressive modulus are increased by about 10 times, and the void ratio and plasticity index can all reach the level of general clay. It shows that alkali slag has the potential to improve marine soft soil and can be popularized in engineering.

scholarly journals Compressibility behaviour of remoulded, fine-grained soils and correlation with index properties

2000 ◽  
Vol 37 (3) ◽  
pp. 712-722 ◽  
Author(s):  
A Sridharan ◽  
H B Nagaraj
Keyword(s):  
Liquid Limit ◽  
Plasticity Index ◽  
Engineering Properties ◽  
Test Results ◽  
Index Properties ◽  
Initial Water ◽  
Fine Grained ◽  
Wide Range ◽  
The Relationship ◽  
Water Contents

Correlating engineering properties with index properties has assumed greater significance in the recent past in the field of geotechnical engineering. Although attempts have been made in the past to correlate compressibility with various index properties individually, all the properties affecting compressibility behaviour have not been considered together in any single study to examine which index property of the soil correlates best with compressibility behaviour, especially within a set of test results. In the present study, 10 soils covering a sufficiently wide range of liquid limit, plastic limit, and shrinkage limit were selected and conventional consolidation tests were carried out starting with their initial water contents almost equal to their respective liquid limits. The compressibility behaviour is vastly different for pairs of soils having nearly the same liquid limit, but different plasticity characteristics. The relationship between void ratio and consolidation pressure is more closely related to the shrinkage index (shrinkage index = liquid limit - shrinkage limit) than to the plasticity index. Wide variations are seen with the liquid limit. For the soils investigated, the compression index relates better with the shrinkage index than with the plasticity index or liquid limit.Key words: Atterberg limits, classification, clays, compressibility, laboratory tests.

scholarly journals Stabilization of Algerian Clayey Soils with Natural Pozzolana and Lime

2017 ◽  
Author(s):  
Khelifa Harichane ◽  
Mohamed Ghrici ◽  
Said Kenai
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Plasticity Index ◽  
Engineering Properties ◽  
High Plasticity ◽  
Expansive Clay ◽  
Clayey Soils ◽  
Natural Pozzolana

Cohesive soils with a high plasticity index present difficulties in construction operations because they usually contain expansive clay minerals. However, the engineering properties of soils can be improved by different techniques. The aim of this paper is to study the effect of using lime, natural pozzolana or a combination of both lime and natural pozzolana on plasticity, compaction and shear strength of two clayey soils classified as CH and CL according to the unified soil classification system (USCS). The obtained results indicated that for CH class clay soil, the plasticity index decreased significantly for samples stabilized with lime. On the other hand, for the soil classified as CL class clay, a high decrease in the plasticity index value was observed for samples stabilized with natural pozzolana compared to those stabilized with lime. Also, both the cohesion and internal friction angle in lime added samples were demonstrated to increase with time. The combination of lime and natural pozzolana exhibits a significant effect on the enhancement of both the cohesion and  internal friction angle at later stages. The lime-natural pozzolana combination appears to produce higher shear strength parameters than lime or natural pozzolana used alone.

scholarly journals Prediction of Shear Strength of Soil Using Direct Shear Test and Support Vector Machine Model

2020 ◽  
Vol 14 (1) ◽  
pp. 41-50 ◽  
Author(s):  
Hai-Bang Ly ◽  
Binh Thai Pham
Keyword(s):  
Support Vector Machine ◽  
Shear Strength ◽  
Moisture Content ◽  
Mean Squared Error ◽  
Learning Algorithm ◽  
Liquid Limit ◽  
Support Vector ◽  
Plastic Limit ◽  
Svm Model ◽  
Soil Shear Strength

Background: Shear strength of soil, the magnitude of shear stress that a soil can maintain, is an important factor in geotechnical engineering. Objective: The main objective of this study is dedicated to the development of a machine learning algorithm, namely Support Vector Machine (SVM) to predict the shear strength of soil based on 6 input variables such as clay content, moisture content, specific gravity, void ratio, liquid limit and plastic limit. Methods: An important number of experimental measurements, including more than 500 samples was gathered from the Long Phu 1 power plant project’s technical reports. The accuracy of the proposed SVM was evaluated using statistical indicators such as the coefficient of correlation (R), Root Mean Squared Error (RMSE), Mean Absolute Error (MAE) over a number of 200 simulations taking into account the random sampling effect. Finally, the most accurate SVM model was used to interpret the prediction results due to Partial Dependence Plots (PDP). Results: Validation results showed that SVM model performed well for prediction of soil shear strength (R = 0.9 to 0.95), and the moisture content, liquid limit and plastic limit were found as the three most affecting features to the prediction of soil shear strength. Conclusion: This study might help in quick and accurate prediction of soil shear strength for practical purposes in civil engineering.

Sign in / Sign up

Export Citation Format

Share Document