EXPERIMENTAL STUDY OF THE ROLLING–SLIDING CONTACT CONDITIONS IN A PA66/STEEL GEAR USING TWIN-DISC TEST RIG: FRICTION AND WEAR ANALYSIS

2015 ◽  
Vol 22 (06) ◽  
pp. 1550074
Author(s):  
MEFTAH MBAREK ◽  
SADOK RHAIEM ◽  
MOHAMED KHARRAT ◽  
MAHER DAMMAK
Keyword(s):  
Coefficient Of Friction ◽  
Angular Speed ◽  
Linear Increase ◽  
Contact Temperature ◽  
Test Rig ◽  
Contact Conditions ◽  
Slip Ratio ◽  
The Coefficient Of Friction ◽  
Adhesive Interactions ◽  
Different Diameters

This study investigates the effects of sliding ratio on the tribological response of the contact between the teeth of a metal/polymer gear in the regions close to the pitch point. For this purpose, a new twin-disc test rig was developed on the basis of two discs of different diameters rotating one above the other at the same angular speed. Two different materials were used: non-alloyed structural steel (C45) and polyamide (PA66). The effect of the slip ratio (4%, 12%, 20% and 28%) was studied at a constant pressure of 34 MPa and a constant angular speed of 300 rpm. In addition, the contact conditions were controlled with measurements of the two discs surface temperatures. The results indicate that the wear and the friction are closely related to the contact temperature generated by the sliding phenomenon. At low slip ratio (4% and 12%), the coefficient of friction and the temperature are characterized by a quasi-linear increase with time, and the wear increases slowly. At higher slip ratio (20% and 28%), the coefficient of friction and the temperature presents a steady state, and the wear increases dramatically. During the test, a film of transferred PA66 is formed on the steel surface causing the development of adhesive interactions between the contacting discs which increase the friction coefficient and the contact temperature. The high thermal conductivity of steel as compared to that of the polymer can reduce enormously the contact temperature generated by the sliding process.

Effect of contact temperature, normal load and dry sliding velocity on the coefficient of friction and wear behavior of nickel based super alloy

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Rama Krishna S. ◽  
Patta Lokanadham
Keyword(s):  
Coefficient Of Friction ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Normal Load ◽  
Contact Temperature ◽  
Sliding Velocity ◽  
Friction And Wear Behavior ◽  
Alloy Material ◽  
The Coefficient Of Friction ◽  
Super Alloy

Purpose The purpose of the present paper aims to, study the coefficient of friction and wear behavior of nickel based super alloys used in manufacturing of gas and steam turbine blades. In present paper, parametric study focuses on normal load, dry sliding velocity and contact temperature influence on coefficient of friction and wear of a nickel based super alloy material. Design/methodology/approach Experimental investigation is carried out to know the effect of varying load at constant sliding velocity and varying sliding velocity at constant load on coefficient of friction and wear behavior of nickel based super alloy material. The experiments are carried out on a nickel based super alloy material using pin on disk apparatus by load ranging from 30 N to 90 N and sliding velocity from 1.34 m/s to 2.67 m/s. The contact temperature between pin and disk is measured using K-type thermocouple for all test conditions to know effect of contact temperature on coefficient of friction and wear behavior of nickel based super alloy material. Analytical calculations are carried out to find wear rate and wear coefficient of the test specimen and are compared with experimental results for validation of experimental setup. Regression equations are generated from experimental results to estimate coefficient of friction and wear in the range of test conditions. Findings From the experimental results, it is observed that by increasing the normal load or sliding velocity, the contact temperature between the pin and disk increases, the coefficient of friction decreases and wear increases. Analysis of variance (ANOVA) is used to study the influence of individual parameters like normal load, dry sliding speed and sliding distance on the coefficient of friction and wear of nickel based super alloy material. Originality/value This is the first time to study effect of contact temperature on the coefficient of friction and wear behavior of nickel-based super alloy used for gas and steam turbine blades. Separate regression equations have been developed to determine the coefficient of friction and wear for the entire range of speed of gas turbine blades made of nickel based super alloy. The regression equations are also validated against experimental results.

scholarly journals A Study of Coefficient of Friction of UHMWPE in Various Contact Conditions and Measurement of Contact Temperature.

2003 ◽  
Vol 69 (677) ◽  
pp. 121-127
Author(s):  
Keiji IMADO ◽  
Atuyoshi MIURA ◽  
Masuji NAGATOSHI ◽  
Hiroomi MIYAGAWA ◽  
Hidehiko HIGAKi
Keyword(s):  
Coefficient Of Friction ◽  
Contact Temperature ◽  
Contact Conditions

scholarly journals The Tribological Adaptability for Ventral Scales of Dinodon rufozonatum in Dry/Wet/Rough Environments

Coatings ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 20
Author(s):  
Song Hu ◽  
Ge Shi ◽  
Qinggang Guo ◽  
Long Zheng ◽  
Luquan Ren ◽  
...  
Keyword(s):  
Coefficient Of Friction ◽  
Water Lubrication ◽  
Substrate Roughness ◽  
Contact Conditions ◽  
Frictional Performance ◽  
The Coefficient Of Friction ◽  
Dry Conditions ◽  
Multiple Environments ◽  
Lubrication Conditions

The ventral scales of Dinodon rufozonatum were investigated to understand the outstanding tribological adaptability in various environments. The coefficient of friction (COF) of ventral scales was measured and changed with the contact conditions. It was discovered that the COF of scales under water-lubrication conditions (WLC) was larger than that under dry conditions (DC). More interestingly, the COF increased first and then decreased as the substrate roughness reduced. The abrasion marks on scales were then observed. The results indicated that the scales in DC wore more gently than that in WLC. Moreover, the degree of wear reduced with the decrease of substrate roughness. The frictional performance of ventral scales enabled the snakes to move more efficiently, quickly, and flexibly in multiple environments.

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

scholarly journals Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4217
Author(s):  
Üsame Ali Usca ◽  
Mahir Uzun ◽  
Mustafa Kuntoğlu ◽  
Serhat Şap ◽  
Khaled Giasin ◽  
...  
Keyword(s):  
Weight Loss ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Practical Significance ◽  
Tribological Characteristics ◽  
M 10 ◽  
Wide Range ◽  
The Coefficient Of Friction ◽  
Four Levels

Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-reinforcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.

scholarly journals Influence of Beam Power on Young’s Modulus and Friction Coefficient of Ti–Ta Alloys Formed by Electron-Beam Surface Alloying

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1246
Author(s):  
Stefan Valkov ◽  
Dimitar Dechev ◽  
Nikolay Ivanov ◽  
Ruslan Bezdushnyi ◽  
Maria Ormanova ◽  
...  
Keyword(s):  
Electron Beam ◽  
Young’S Modulus ◽  
Coefficient Of Friction ◽  
Young's Modulus ◽  
Beam Power ◽  
Surface Alloying ◽  
Surface Alloys ◽  
X Ray ◽  
The Coefficient Of Friction ◽  
Beam Surface

In this study, we present the results of Young’s modulus and coefficient of friction (COF) of Ti–Ta surface alloys formed by electron-beam surface alloying by a scanning electron beam. Ta films were deposited on the top of Ti substrates, and the specimens were then electron-beam surface alloyed, where the beam power was varied from 750 to 1750 W. The structure of the samples was characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). Young’s modulus was studied by a nanoindentation test. The coefficient of friction was studied by a micromechanical wear experiment. It was found that at 750 W, the Ta film remained undissolved on the top of the Ti, and no alloyed zone was observed. By an increase in the beam power to 1250 and 1750 W, a distinguished alloyed zone is formed, where it is much thicker in the case of 1750 W. The structure of the obtained surface alloys is in the form of double-phase α’and β. In both surface alloys formed by a beam power of 1250 and 1750 W, respectively, Young’s modulus decreases about two times due to different reasons: in the case of alloying by 1250 W, the observed drop is attributed to the larger amount of the β phase, while at 1750 W is it due to the weaker binding forces between the atoms. The results obtained for the COF show that the formation of the Ti–Ta surface alloy on the top of Ti substrate leads to a decrease in the coefficient of friction, where the effect is more pronounced in the case of the formation of Ti–Ta surface alloys by a beam power of 1250 W.

Reducing the Coefficient of Friction for Fast-Absorbing Gut Suture

2009 ◽  
Vol 35 (12) ◽  
pp. 2004 ◽  
Author(s):  
Jonathan Lee Bingham ◽  
Mariah R. Brown ◽  
Julian Ramsey Mellette
Keyword(s):  
Coefficient Of Friction ◽  
The Coefficient Of Friction
Sign in / Sign up

Export Citation Format

Share Document