LOW-TEMPERATURE NITRIDING BEHAVIOR OF COMPRESSIVE DEFORMED AISI 316Ti AUSTENITIC STAINLESS STEELS

2019 ◽  
Vol 26 (05) ◽  
pp. 1850188 ◽  
Author(s):  
FATIH KAHRAMAN ◽  
GÖKÇE MEHMET GENÇER ◽  
AYÇA D. KAHRAMAN ◽  
COŞKUN YOLCU ◽  
HAYDAR KAHRAMAN
Keyword(s):  
Low Temperature ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Cold Deformation ◽  
Surface Hardness ◽  
Compound Layer ◽  
Optical Microscope ◽  
Layer Growth ◽  
Nitrogen Diffusion ◽  
Undeformed Sample

The effects of compressive cold deformation under the quasi-static loads on the nitride formation, nitride layer growth and surface hardness properties were researched in this study. Martensite structure did not form in AISI 316Ti stainless steel as a result of quasi-static deformation. Diffusion layer did not form in all nitrided samples. Both the deformed and undeformed samples have only compound layer on the surfaces at the low-temperature nitriding conditions (400∘C, 7[Formula: see text]h). According to the X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS) and electron probe microanalysis (EPMA) results, S-phase and chromium nitride (CrN) were formed in the compound layers of the deformed samples. However, CrN did not form in the compound layer of the undeformed sample. The optical microscope (OM) results showed that the compressive cold deformation increased the nitrogen diffusion rate and led to thicker nitrided layer than the undeformed sample under the same plasma-nitriding conditions. All nitrided layers presented higher microhardness values ([Formula: see text][Formula: see text]HV) when compared with the untreated sample hardness. It was also verified that the deformation amount did not affect significantly the nitrided layer hardness.

The Characteristics of Surface Layers Produced on SKD 61 Steel by Plasma Radical Nitriding Compared with Conventional Plasma Ion Nitriding

2006 ◽  
Vol 118 ◽  
pp. 155-160
Author(s):  
Insup Lee ◽  
Yong Ho Park ◽  
Ik Min Park
Keyword(s):  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Surface Hardness ◽  
Compound Layer ◽  
Hardened Layer ◽  
Processing Parameters ◽  
Polished Surface ◽  
Nitrogen Diffusion ◽  
Ion Nitriding ◽  
Surface Layers

Plasma radical nitriding has been performed to harden the surface of SKD 61 steel for 1- 10 hours at temperature range of 450-550°C. A NH radical, which has played a key role to produce a nitrogen diffusion layer without the formation of the brittle compound layer, has been generated in a gas mixture of NH3 and H2 . One of the main advantages of the plasma radical nitriding is to improve the surface hardness by maintaining the roughness of the initial polished surface. The microstructures and material properties of the radical nitrided layer have been characterized in order to investigate the effects of various radical nitriding processing parameters. The hardness and surface roughness of the hardened layer were compared between two processes. In addition, PVD CrN coating has been deposited on both the radical nitrided substrates and conventional nitrided substrates by an arc ion plating (AIP) technique. The effect of two different of plasma nitriding treatments on the adhesive strength of the coating layer on the substrates was also investigated.

scholarly journals Acceleration of Plasma Nitriding at 550 °C with Rare Earth on the Surface of 38CrMoAl Steel

Coatings ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1122
Author(s):  
Dongjing Liu ◽  
Yuan You ◽  
Mufu Yan ◽  
Hongtao Chen ◽  
Rui Li ◽  
...  
Keyword(s):  
Rare Earth ◽  
Electron Microscope ◽  
Weight Gain ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Surface Hardness ◽  
Optical Microscope ◽  
Steel Microstructure ◽  
Transmission Electron ◽  
Modified Layer

In order to explore the effect of the addition of rare earth (RE) to a steel microstructure and the consequent performance of a nitrided layer, plasma nitriding was carried out on 38CrMoAl steel in an atmosphere of NH3 at 550 °C for 4, 8, and 12 h. The modified layers were characterized using an optical microscope (OM), a microhardness tester, X-ray diffraction (XRD), a scanning electron microscope (SEM), a transmission electron microscope (TEM), and an electrochemical workstation. After 12 h of nitriding without RE, the modified layer thickness was 355.90 μm, the weight gain was 3.75 mg/cm2, and the surface hardness was 882.5 HV0.05. After 12 h of RE nitriding, the thickness of the modified layer was 390.8 μm, the weight gain was 3.87 mg/cm2, and the surface hardness was 1027 HV0.05. Compared with nitriding without RE, the ε-Fe2-3N diffraction peak was enhanced in the RE nitriding layer. After 12 h of RE nitriding, La, LaFeO3, and a trace amount of Fe2O3 appeared. The corrosion rate of the modified layer was at its lowest (15.089 × 10−2 mm/a), as was the current density (1.282 × 10−5 A/cm2); therefore, the corrosion resistance improved.

scholarly journals Combating the Tribo-Corrosion of LDX2404 Lean Duplex Stainless Steel by Low Temperature Plasma Nitriding

Lubricants ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 93 ◽  
Author(s):  
Xiaoying Li ◽  
Wenbo Dou ◽  
Linhai Tian ◽  
Hanshan Dong
Keyword(s):  
Stainless Steel ◽  
Low Temperature ◽  
Duplex Stainless Steel ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Surface Hardness ◽  
Electrochemical Corrosion ◽  
Treatment Temperature ◽  
Temperature Plasma ◽  
Lean Duplex Stainless Steel

A lean duplex stainless steel, LDX2404, was DC plasma nitrided under a range of treatment conditions. The microstructure characterisation evaluation of the treated samples revealed that a dense, super-hard surface layer can be produced by low-temperature (<450 °C) plasma treatments. The original austenite phase became S-phase and the ferrite phase was supersaturated with nitrogen and ε-Fe3N nitride precipitated from it. When plasma nitriding was carried out at above 450 °C, chromium nitrides precipitated in the surface nitrided layer. Compared to the untreated samples, the surface hardness of the lean duplex stainless steel (DSS) is increased up to four times. The dry wear resistance increased when increasing the treatment temperature. In contrast, the low-temperature treated samples showed the best performance in the electrochemical corrosion and corrosion-wear tests; the performance of the high temperature (>450 °C) plasma nitrided samples was found to be significantly worse than that of the untreated material.

Surface Modification of SS2205 Duplex Stainless Steel by Plasma Nitriding at Anodic Potential

2014 ◽  
Vol 881-883 ◽  
pp. 1263-1267 ◽  
Author(s):  
Shuo Zhao ◽  
Liang Wang ◽  
Jiu Jun Xu ◽  
Y. Shan
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Low Temperature ◽  
Duplex Stainless Steel ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Surface Hardness ◽  
Anodic Potential ◽  
Wear And Corrosion

The duplex stainless steel has better pitting corrosion resistance but lacks of hardness and wear resistance. Therefore, the low temperature nitriding treatment can be used to increase its hardness and wear resistance or to gain more perfect corrosion resistance. The plasma nitriding of SS2205 stainless steel was carried out at temperatures from 693k to 753k for 4 hours at anodic potential. The nitrided samples were analyzed by optical microscopy, X-ray diffraction, SEM-EDX analysis, microhardness testing, wear and corrosion evaluation. The XRD analysis of all treated samples showed that the nitrogen-expanded austenite phase was formed. Both α and γ phase of the substrate were transformed into γNduring plasma nitriding. Observing the nitrided layers formed on α and γ phase, the ones situated in the austenite were thinner than the ones in the ferrite. This phenomenon was more evident at low temperature, which confirmed that the nitrogen has a higher diffusion rate in the ferrite during plasma nitriding treatment. The surface hardness of nitrided layer was increased with the nitriding temperature. The highest hardness value obtained in this experiment was about 1300 HV0.05which was 4 times as the original sample (380 HV0.05). Furthermore, through the wear and corrosion property tests, it was shown that anodic plasma nitriding improved the wear resistance and corrosion resistance of the duplex stainless steel.

EFFECT OF NITROGEN AMOUNT ON TRIBOLOGICAL BEHAVIOR OF PLASMA NITRIDED 31CrMoV9 STEEL

2019 ◽  
Vol 26 (07) ◽  
pp. 1850217 ◽  
Author(s):  
O. ÇOMAKLI ◽  
A. F. YETIM ◽  
B. KARACA ◽  
A. ÇELIK
Keyword(s):  
Wear Resistance ◽  
Tribological Behavior ◽  
Wear Behavior ◽  
Plasma Nitriding ◽  
Surface Hardness ◽  
Compound Layer ◽  
Gas Mixture ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pin On Disk

The 31CrMoV9 steels were plasma nitrided under different gas mixture ratios to investigate an influence of nitrogen amount on wear behavior. The structure, mechanical and tribological behavior of untreated and nitrided 31CrMoV9 steels were analyzed with X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), microhardness device, 3D profilometer and pin-on-disk wear tester. The analysis outcomes displayed that the compound layer consists of nitride phases (Fe2N, Fe3N, Fe4N and CrN). Additionally, the thickness of the compound layers, surface hardness and roughness increased with increasing nitrogen amount in the gas mixture. The highest friction coefficient value was obtained at nitrogen amount of 50%, but the lowest value was seen at nitrogen amount of 6%. It was observed that wear resistance of 31CrMoV9 steel improved after plasma nitriding, and the best wear resistance was also obtained from plasma nitrided sample at the gas mixture of 94% H[Formula: see text]% N2.

Novel Electrodeposited Ni-Based Nanocomposite Precursors for Nitriding and Low Temperature Chromizing

2006 ◽  
Vol 522-523 ◽  
pp. 331-338
Author(s):  
X. Peng ◽  
J. Zhao ◽  
Hong Yan Zhang ◽  
Fu Hui Wang
Keyword(s):  
Low Temperature ◽  
Oxidation Resistance ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Pack Cementation ◽  
Coarse Grained ◽  
Crn Coating ◽  
Cr Content ◽  
Oxidation Resistant

Two types of Ni-base nanocomposites were prepared by co-deposition of Ni with nano-sized particles of Cr or CeO2, respectively. Both Ni-Cr and Ni-CeO2 nanocomposites were mainly composed of nanocrystalline Ni matrix, in which certain content of nanoparticles of Cr or CeO2 randomly dispersed. The Ni-Cr nanocomposite was used as a precursor for preparing a novel hard Ni/CrN coating by plasma nitriding at 560oC. The Ni-CeO2 nanocomposite was used as a precursor to develop a novel oxidation-resistant chromia-forming coating by low temperature chromizing using a conventional pack-cementation method. The microhardness of the nitrided layer on the Ni-Cr nanocomposite and the oxidation resistance of the chromizing coating on the Ni-CeO2 nanocomposite were both greatly increased, in comparison to the corresponding counterparts, which were obtained by plasma nitriding on a conventional coarse-grained Ni-Cr alloy with similar Cr content and by chromizing on a coarse-grained Ni metal, respectively. The relationships among the microstructures of the nanocomposite precursors and the nitrided/or chromized coatings, and their properties were investigated and discussed.

scholarly journals Effects of Surface Modification by Means of Low-Temperature Plasma Nitriding on Wetting and Corrosion Behavior of Austenitic Stainless Steel

Coatings ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 98 ◽  
Author(s):  
Francesca Borgioli ◽  
Emanuele Galvanetto ◽  
Tiberio Bacci
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Corrosion Resistance ◽  
Low Temperature ◽  
Surface Morphology ◽  
Corrosion Behavior ◽  
Sessile Drop ◽  
Plasma Nitriding ◽  
Surface Hardness ◽  
Temperature Plasma

Low-temperature nitriding of austenitic stainless steels produces modified surface layers, consisting mainly of the S phase, which improve surface hardness and corrosion resistance. Because of the localized plastic deformations, owing to modified layer formation, and ion bombardment occurring during the process itself, this treatment produces also modifications of surface morphology and roughness, which can affect wettability and corrosion behavior. In this study the effects of plasma nitriding, performed using different treatment conditions, on the surface morphology and roughness, and thus on wettability and corrosion resistance, of AISI 202 specimens with different initial finishings (2D and polished finishing) were investigated. Different probe liquids, having both high (bi-distilled water and solution of 3.5% NaCl) and low (ethanol and rapeseed oil) surface tension, were employed for assessing the wetting behavior with the sessile drop method. The contact angle values for water increased markedly when nitriding was performed on polished samples, while this increase was smaller for 2D samples, and on selected specimens a hydrophobic behavior was observed. Very low contact angle values were registered using low surface tension liquids, suggesting an oleophilic behavior. Corrosion resistance in a 5% NaCl solution was assessed, and it depended on the characteristics of the nitrided specimens.

scholarly journals Mathematical Modelling of Nitride Layer Growth of Low Temperature Gas and Plasma Nitriding of AISI 316L

2014 ◽  
Vol 13 ◽  
pp. 04022
Author(s):  
A. Triwiyanto ◽  
A. Zainuddin ◽  
K.A.Z Abidin ◽  
M.A Billah ◽  
P. Hussain
Keyword(s):  
Low Temperature ◽  
Mathematical Modelling ◽  
Plasma Nitriding ◽  
Nitride Layer ◽  
Layer Growth ◽  
Aisi 316L

Ti6Al4V Surface Hardness Improvement by Duplex Coating

2013 ◽  
Vol 701 ◽  
pp. 370-374
Author(s):  
Yusliza Yusuf ◽  
Zulkifli Mohd Rosli ◽  
Jariah Mohamad Juoi ◽  
Zainab Mahamud ◽  
Kwan Wai Loon
Keyword(s):  
Microwave Plasma ◽  
Plasma Nitriding ◽  
Microstructural Analysis ◽  
Surface Hardness ◽  
Hardness Measurement ◽  
Compound Layer ◽  
Ti6al4v Alloy ◽  
Process Time ◽  
Wear Properties ◽  
Duplex Coating

Ti6Al4V alloy are among the most widely used materials in engineering applications. This is because their relatively beneficial properties. However, inadequate wear properties of Ti6Al4V alloy have largely constrained the application for this material. In this study, Plasma nitriding of the Ti6Al4V was performed using microwave plasma technique at 600°C for 1hour, 3 hours and 5 hours then followed with deposition of CrN on plasma nitrided samples for duplex coating purposes. Microstructural analysis and hardness measurement revealed that formation of Ti2N and TiN phases indicating the formation of compound layer is observed for substrate nitrided at temperature as low as 600°C 1 hour and a substantial increase on the surface hardness of plasma nitrided Ti6Al4V is observed with an increase of process time. The duplex coating obtained in this study has significant surface hardness property and superior as compared with CrN coatings deposited on as received Ti6Al4V.

Low Temperature Fluidized Bed Nitriding of Austenitic Stainless Steel

2006 ◽  
Vol 118 ◽  
pp. 125-130 ◽  
Author(s):  
E. Haruman ◽  
Y. Sun ◽  
H. Malik ◽  
Agus Geter E. Sutjipto ◽  
S. Mridha ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Low Temperature ◽  
Fluidized Bed ◽  
Corrosion Behaviour ◽  
Plasma Nitriding ◽  
Nitrided Layer ◽  
Temperature Plasma ◽  
316L Austenitic Stainless Steel ◽  
Fluidized Bed Process

In the present investigation, low temperature nitriding has been attempted on AISI 316L austenitic stainless steel by using a laboratory fluidized bed furnace. The nitriding was performed in temperature range between 400°C and 500°C. X-ray diffraction, metallography, and corrosion tests were used to characterize the resultant nitrided surface and layers. The results showed that fluidized bed process can be used to produce a precipitation-free nitrided layer characterized by the S phase or expanded austenite on austenitic stainless steel at temperatures below 500°C. But there exists a critical temperature and an incubation time for effective nitriding, below which nitriding is ineffective. The corrosion behaviour of the as-nitrided surfaces is significantly different from that previously reported for low temperature plasma nitriding. This anomaly is explained by the formation of iron oxide products and surface contamination during the fluidized process.

Sign in / Sign up

Export Citation Format

Share Document