Preparation and Characterization of Nitrogen-Containing Cellular Activated Carbon for CO2 and H2 Adsorption

NANO ◽  
2017 ◽  
Vol 12 (01) ◽  
pp. 1750007 ◽  
Author(s):  
Weigang Zhao ◽  
Lu Luo ◽  
Mizi Fan
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Atmospheric Pressure ◽  
Activated Carbons ◽  
Urea Formaldehyde ◽  
Testing Machine ◽  
Physical Activation ◽  
Activation Time ◽  
H2 Adsorption

New monolithic nitrogen-containing microporous cellular activated carbon was successfully prepared from phenol-urea-formaldehyde (PUF) organic foam for CO2 and H2 adsorption and was characterized by thermogravimetric analysis (TG), scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), elemental analysis (EA), a mechanical testing machine, N2-sorption and H2/CO2 sorption. The carbon yield was approximately 50% for carbonization and the burn off for activation ranged from 40% to 56%, which linearly increased with activation time. The macroporosity corresponded to the connected network of cells with diameters ranging from 100[Formula: see text][Formula: see text]m to 600[Formula: see text][Formula: see text]m, and the pinholes in the cell walls had diameters ranging from 1[Formula: see text][Formula: see text]m to 2[Formula: see text][Formula: see text]m. The micro/mesoporosity is located at the inner surface of the cells. Thus, higher adsorption kinetics than usual from activated carbon are expected. The developed carbon with the highest [Formula: see text] (1674 m2/g) and highest [Formula: see text] (0.86[Formula: see text]cm3/g) contained 1.5% nitrogen, had a CO2 adsorption capacity of 3.53[Formula: see text]mmol/g at 298[Formula: see text]K, and had an H2 adsorption capacity of 1.9[Formula: see text]wt.% at 77[Formula: see text]K, both at atmospheric pressure (1 bar), which were among the best in activated carbons from physical activation.

scholarly journals Production and Characterization of Activated Carbon from Coal for Gold Adsorption in Cyanide Solutions

2020 ◽  
Vol 40 (1) ◽  
pp. 34-44
Author(s):  
Karen L. Martínez-Mendoza ◽  
Juan Manuel Barraza Burgos ◽  
Nilson Marriaga-Cabrales ◽  
Fiderman Machuca-Martinez ◽  
Mariber Barajas ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Physical Activation ◽  
Adsorption Model ◽  
Waste Solution ◽  
Synthetic Solution ◽  
Cyanide Solutions ◽  
Two Stages ◽  
Characterization Of Activated Carbon

In this work, activated carbons were produced using coal as raw matter from seven Colombian carboniferous zones. Physical activation was performed in two stages: a carbonization stage with Nitrogen at a temperature of 850 °C and a residence time of 2 h, followed by an activation stage using steam at temperatures of 700 and 850 °C with residence times of 1,5 h and 2,5 h. From the pore volume characterization for the adsorption of gold, two activated carbons from Cundinamarca, obtained at 850 °C (1,5 h), 850 °C (2,5 h), and a commercial carbon (GRC 22) were selected. Gold adsorption tests were performed with those three activated carbons using synthetic aurocyanide solutions and a gold waste solution. The data of the adsorption isotherms were adjusted using the Freundlich adsorption model for the synthetic solution, as well as Langmuir for the waste solution. The results showed that, using a solution of 1 ppm, the activated carbons C-850-2.5 and C- 850-1.5 produced the higher maximum gold loading capacities in the equilibrium (8,7 and 9,3 mg Au/g, respectively) in comparison to the commercial activated carbon (4,7 mg Au/g).  Gold adsorption test using a waste solution (21 ppm of gold) showed that the activated carbon C-850-1.5 had the highest value of adsorption capacity (4,58 mg Au/g) compared to C-850-2.5 (2,95 mgAu /g).

scholarly journals CO2 and CH4 Adsorption Behavior of Biomass-Based Activated Carbons

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3136 ◽  
Author(s):  
Deneb Peredo-Mancilla ◽  
Imen Ghouma ◽  
Cecile Hort ◽  
Camelia Matei Ghimbeu ◽  
Mejdi Jeguirim ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Gas Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Micropore Volume ◽  
Activation Method ◽  
Physical Activation

The aim of the present work is to study the effect of different activation methods for the production of a biomass-based activated carbon on the CO 2 and CH 4 adsorption. The influence of the activation method on the adsorption uptake was studied using three activated carbons obtained by different activation methods (H 3 PO 4 chemical activation and H 2 O and CO 2 physical activation) of olive stones. Methane and carbon dioxide pure gas adsorption experiments were carried out at two working temperatures (303.15 and 323.15 K). The influence of the activation method on the adsorption uptake was studied in terms of both textural properties and surface chemistry. For the three adsorbents, the CO 2 adsorption was more important than that of CH 4 . The chemically-activated carbon presented a higher specific surface area and micropore volume, which led to a higher adsorption capacity of both CO 2 and CH 4 . For methane adsorption, the presence of mesopores facilitated the diffusion of the gas molecules into the micropores. In the case of carbon dioxide adsorption, the presence of more oxygen groups on the water vapor-activated carbon enhanced its adsorption capacity.

scholarly journals PEMBUATAN KARBON AKTIF DARI KULIT SALAK (Salacca Zalacca) DENGAN PROSES FISIKA MENGGUNAKAN UAP DENGAN PEMANAS MICROWAVE

2018 ◽  
Vol 6 (4) ◽  
pp. 45-49
Author(s):  
Indah Sari ◽  
Uchi Inda Purnamasari ◽  
M. Turmuzi Lubis
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Microwave Power ◽  
Oxide Content ◽  
Activation Time ◽  
Activated Carbon Adsorption ◽  
X Ray ◽  
Carbon Adsorption ◽  
Active Substances

This study aimed to determine the best adsorption capacity, compounds contained in activated carbon and burn off that produced. In this study, activated carbon have been prepared from the bark of Salacca zalacca by physically activating using a microwave. The 70 gram  bark of Salacca zalaccawas pyrolised in a furnace with flowing gas N2 with temperature 500 oC for 120 minutes followed by microwave activation at 2450 MHz with power 600 W, 800 W and 1000 W for 20 minutes, 40 minutes and 60 minutes. The results showed the best burn off on microwave power 1000 W with 60 minutes activation time of 90,25%. The best activated carbon adsorption capacity at 800 W microwave power for 20 minutes is 19,96 mg/g. The best allowanced percentage at 800 W microwave power with 20 minutes activation time is 99,82%. Characterization of Fourier Transform Infra-Red (FITR) showed the presence of C=O (carbonyl) bonds indicating the presence of carbon-active substances. After pyrolysis forms a C≡C (Alkuna) bond which indicated more carbon was produced. This is supported by the characterization of Scanning Electron Microscope (SEM) and Energy Dispersive X-Ray Spectroscopy (EDS) showing the surface morphology of rough and irregular activated carbon and the amount of carbon and oxide content on activated carbon of 44,44% and 28,54% sequentially.

Activated Carbon Prepared from Date Pits for the Retention of NO2 at Low Temperature

2014 ◽  
Vol 12 (2) ◽  
pp. 717-726 ◽  
Author(s):  
Zohra Belala ◽  
Meriem Belhachemi ◽  
Mejdi Jeguirim
Keyword(s):  
Activated Carbon ◽  
Low Temperature ◽  
Adsorption Capacity ◽  
Activated Carbons ◽  
Textural Properties ◽  
Operating Conditions ◽  
Physical Activation ◽  
Maximum Adsorption Capacity ◽  
Increasing Temperature ◽  
Date Pits

Abstract Activated carbons were prepared from date pits by physical activation with CO2 and the textural properties were investigated by BET and D-R methods with N2 and CO2 adsorption isotherms. The interaction of the NO2 with activated carbon was examined at ambient temperature and the effect of operating conditions such as temperature and inlet gas compositions was also examined. It was observed that the development of porosity with increasing time of activation favours the adsorption capacity of NO2. The maximum adsorption capacity reached was about 107 mg/g, which is higher than several activated carbon prepared from classical lignocellulosic biomass. However, a slight decrease of NO2 adsorption capacity was observed with increasing temperature. The addition of oxygen into the inlet gas gave rise to an increase in amount adsorbed of NO2.

Preparation and Characterization of Activated Carbon from Palm Shell by Catalytic Activation with Steam

2013 ◽  
Vol 787 ◽  
pp. 46-51 ◽  
Author(s):  
Hao Guo ◽  
Xian Lun Deng
Keyword(s):  
Activated Carbon ◽  
Potassium Carbonate ◽  
Activated Carbons ◽  
Potassium Phosphate ◽  
Nitrogen Adsorption ◽  
Physical Activation ◽  
Catalytic Activation ◽  
Palm Shell ◽  
Nitrogen Adsorption Isotherms

The use of palm shells as a precursor for the production of activated carbon with physical activation was investigated. The carbonized material was impregnated with potassium carbonate and potassium phosphate to improve the yield and adsorption capability of activated carbon. The produced activated carbons were characterized by Iodine number text, Methylene blue adsorption text, Nitrogen adsorption isotherms, Scanning electron microscope in order to understand the palm shell activated carbon. The results showed that palm shell is an appropriate precursor for activated carbon. The optimum activation condition is: temperature 850°C, activating time 60 min, and steam flow rate 1.0g min-1. Potassium carbonate-impregnated and potassium phosphate-impregnated sample showed higher value of surface area which attained 982m2/g and 973m2/g, respectively.

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

PREPARATION AND CHARACTERIZATION OF ACTIVATED CARBON FROM OIL PALM EMPTY FRUIT BUNCH WASTES USING ZINC CHLORIDE

2015 ◽  
Vol 74 (11) ◽  
Author(s):  
Riry Wirasnita ◽  
Tony Hadibarata ◽  
Abdull Rahim Mohd Yusoff ◽  
Zainab Mat Lazim
Keyword(s):  
Activated Carbon ◽  
Zinc Chloride ◽  
Oil Palm ◽  
Active Sites ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Proximate Analysis ◽  
Infrared Spectrometry ◽  
Empty Fruit Bunch

An oil palm empty fruit bunch-derived activated carbon has been successfully produced by chemical activation with zinc chloride and without chemical activation. The preparation was conducted in the tube furnace at 500oC for 1 h. The surface structure and active sites of activated carbons were characterized by means of Fourier transform infrared spectrometry and field emission scanning electron microscopy. The proximate analysis including moisture content, ash content, bulk density, pH, and pH at zero charge was conducted to identify the psychochemical properties of the adsorbent. The results showed that the zinc chloride-activated carbon has better characteristics compared to the carbon without chemical activation.  

scholarly journals Removal of Ni (II) from Aqueous Solution by Adsorption onto Activated Carbon Prepared from Lapsi (Choerospondias axillaris) Seed Stone

2014 ◽  
Vol 9 (1) ◽  
pp. 166-174 ◽  
Author(s):  
Rajeshwar M. Shrestha ◽  
Margit Varga ◽  
Imre Varga ◽  
Amar P. Yadav ◽  
Bhadra P. Pokharel ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Characterization ◽  
Maximum Adsorption Capacity ◽  
Adsorption Data ◽  
Optimum Ph ◽  
Nickel Adsorption

Activated carbons were prepared from Lapsi seed stone by the treatment with H2SO4 and HNO3 for the removal of Ni (II) ions from aqueous solution. Two activated carbon have been prepared from Lapsi seed stones by treating with conc.H2SO4 and a mixture of H2SO4 and HNO3 in the ratio of 1:1 by weight for removal of Ni(II) ions. Chemical characterization of the resultant activated carbons was studied by Fourier Transform Infrared Spectroscopy and Boehm titration which revealed the presence of oxygen containing surface functional groups like carboxyl, lactones and phenols in the carbons. The optimum pH for nickel adsorption is found to be 5. The adsorption data were better fitted with the Langmuir equations than Freundlich adsorption equation to describe the equilibrium isotherms. The maximum adsorption capacity of Ni (II) on the resultant activated carbons was 28.25.8 mg g-1 with H2SO4 and 69.49 mg g-1 with a mixture of H2SO4 and HNO3. The waste material used in the preparation of the activated carbons is inexpensive and readily available. Hence the carbons prepared from Lapsi seed stones can act as potential low cost adsorbents for the removal of Ni (II) from water. DOI: http://dx.doi.org/10.3126/jie.v9i1.10680Journal of the Institute of Engineering, Vol. 9, No. 1, pp. 166–174

scholarly journals Preparation and characterization of activated carbons from albizia saman pod

2017 ◽  
Vol 36 (3) ◽  
pp. 44-53
Author(s):  
G. D. Akpen ◽  
M. I. Aho ◽  
N. Baba
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Volatile Matter ◽  
Sieve Analysis ◽  
Albizia Saman ◽  
Temperature Surface

Activated carbon was prepared from the pods of Albizia saman for the purpose of converting the waste to wealth. The pods were thoroughly washed with water to remove any dirt, air- dried and cut into sizes of 2-4 cm. The prepared pods were then carbonised in a muffle furnace at temperatures of 4000C, 5000C, 6000C ,7000C and 8000C for 30 minutes. The same procedure was repeated for 60, 90, 120 and 150 minutes respectively. Activation was done using impregnationratios of 1:12, 1:6, 1:4, 1:3, and 1:2 respectively of ZnCl2 to carbonised Albizia saman pods by weight. The activated carbon was then dried in an oven at 1050C before crushing for sieve analysis. The following properties of the produced Albizia saman pod activated carbon (ASPAC) were determined: bulk density, carbon yield, surface area and ash, volatile matter and moisture contents. The highest surface area of 1479.29 m2/g was obtained at the optimum impregnation ratio, carbonization time and temperature of 1:6, 60 minutes and 5000C respectively. It was recommended that activated carbon should be prepared from Albizia saman pod with high potential for adsorption of pollutants given the high surface area obtained.Keywords: Albizia saman pod, activated carbon, carbonization, temperature, surface area

Sign in / Sign up

Export Citation Format

Share Document