scholarly journals Enhancement of Lipase Enzyme Activity in Non-Aqueous Media through a Rapid Three Phase Partitioning and Microwave Irradiation

2008 ◽  
Vol 5 (4) ◽  
pp. 864-871 ◽  
Author(s):  
N. Saifuddin ◽  
A. Z. Raziah
Keyword(s):  
Microwave Irradiation ◽  
Enzyme Stability ◽  
Aqueous Media ◽  
Reaction Rates ◽  
Initial Reaction ◽  
Phase Partitioning ◽  
Three Phase ◽  
Wide Range ◽  
Time Required ◽  
Separation Strategy

Three phase partitioning is fast developing as a novel bio-separation strategy with a wide range of applications including enzyme stability and enhancement of its catalytic activity. pH tuning of enzyme is now well known for use in non-aqueous systems. Tuned enzyme was prepared using a rapid drying technique of microwave dehydration (time required around 15 minutes). Further enhancement was achieved by three phase partitioning (TPP) method. With optimal condition of ammonium sulphate andt-butanol, the protein appeared as an interfacial precipitate between uppert-butanol and lower aqueous phases. In this study we report the results on the lipase which has been subjected to pH tuning and TPP, which clearly indicate the remarkable increase in the initial rate of transesterification by 3.8 times. Microwave irradiation was found to increase the initial reaction rates by further 1.6 times, hence giving a combined increase in activity of about 5.4 times. Hence it is shown that microwave irradiation can be used in conjunction with other strategies (like pH tuning and TPP) for enhancing initial reaction rates.

scholarly journals Ureido Functionalization through Amine-Urea Transamidation under Mild Reaction Conditions

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1583
Author(s):  
Natalia Guerrero-Alburquerque ◽  
Shanyu Zhao ◽  
Daniel Rentsch ◽  
Matthias M. Koebel ◽  
Marco Lattuada ◽  
...  
Keyword(s):  
Aqueous Media ◽  
Reaction Times ◽  
Reaction Rates ◽  
Secondary Amines ◽  
Isocyanic Acid ◽  
Advantages And Disadvantages ◽  
Major Disadvantage ◽  
Wide Range ◽  
Potential Alternative ◽  
Full Conversion

Ureido-functionalized compounds play an indispensable role in important biochemical processes, as well as chemical synthesis and production. Isocyanates, and KOCN in particular, are the preferred reagents for the ureido functionalization of amine-bearing compounds. In this study, we evaluate the potential of urea as a reagent to graft ureido groups onto amines at relatively low temperatures (<100 °C) in aqueous media. Urea is an inexpensive, non-toxic and biocompatible potential alternative to KOCN for ureido functionalization. From as early as 1864, urea was the go-to reagent for polyurea polycondensation, before falling into disuse after the advent of isocyanate chemistry. We systematically re-investigate the advantages and disadvantages of urea for amine transamidation. High ureido-functionalization conversion was obtained for a wide range of substrates, including primary and secondary amines and amino acids. Reaction times are nearly independent of substrate and pH, but excess urea is required for practically feasible reaction rates. Near full conversion of amines into ureido can be achieved within 10 h at 90 °C and within 24 h at 80 °C, and much slower reaction rates were determined at lower temperatures. The importance of the urea/amine ratio and the temperature dependence of the reaction rates indicate that urea decomposition into an isocyanic acid or a carbamate intermediate is the rate-limiting step. The presence of water leads to a modest increase in reaction rates, but the full conversion of amino groups into ureido groups is also possible in the absence of water in neat alcohol, consistent with a reaction mechanism mediated by an isocyanic acid intermediate (where the water assists in the proton transfer). Hence, the reaction with urea avoids the use of toxic isocyanate reagents by in situ generation of the reactive isocyanate intermediate, but the requirement to separate the excess urea from the reaction product remains a major disadvantage.

A Facile, Efficient and Solvent-Free Titanium (IV) Ethoxide Catalysed Knoevenagel Condensation of Aldehydes and Active Methylenes

2020 ◽  
Vol 17 (2) ◽  
pp. 107-115
Author(s):  
Manjunatha M. Ramaiah ◽  
Nanjunda Swamy Shivananju ◽  
Priya Babu Shubha
Keyword(s):  
Microwave Irradiation ◽  
Knoevenagel Condensation ◽  
Ethyl Cyanoacetate ◽  
Diethyl Malonate ◽  
Aromatic Aldehydes ◽  
Reaction Rates ◽  
Solvent Free ◽  
Solvent Free Conditions ◽  
Wide Range ◽  
Titanium Ethoxide

: Titanium ethoxide has been employed as a novel and efficient reagent for the Knoevenagel condensation of aldehydes with active methylenes such as diethyl malonate and ethyl cyanoacetate under solvent free conditions to afford substituted olefins in high to excellent yields. The reaction is suitable for a variety of aromatic, aliphatic and heteroaromatic aldehydes with various active methylenes. Parallel to this, microwave irradiation has been utilized to achieve improved reaction rates and enhanced yields. Herein, we illustrated a convenient method for the preparation of α,β-unsaturated compounds using both conventional and microwave irradiation methods. An efficient and solvent free Knoevenagel condensation between aldehydes and active methylenes was developed using titanium ethoxide. The procedure proved to be successful with a wide range of substrates such as aromatic, aliphatic and heterocyclic aldehydes and various active methylenes to afford substituted olefins. The reaction was also carried out under microwave irradiation to accomplish the corresponding olefins with improved reaction rates, yields and cleaner reaction profiles.We have developed an efficient and novel methodology for the synthesis of olefinic compounds by Knoevenagel condensation under solvent-free conditions using titanium ethoxide, for the first time, as a reagent as well as a solvent. This method is appropriate for the synthesis of a variety of aromatic aldehydes containing various electron-donating and withdrawing groups, aliphatic and heteroaromatic aldehydes. The significant advantages offered by this methodology could be applied to various active methylenes in order to offer the corresponding Knoevenagel products. Thus, we believe that this method delivers high conversions, cleaner reaction profiles under solvent-free reaction conditions and shorter reaction times, all of which make it a very useful and attractive approach for the preparation of a wide range of substituted olefins.

Microwaves: Application in Electron Microscopy

1990 ◽  
Vol 48 (3) ◽  
pp. 140-141
Author(s):  
Anthony S-Y Leong ◽  
David W Gove
Keyword(s):  
Electron Microscopy ◽  
Light Microscopy ◽  
Chemical Reactions ◽  
Electromagnetic Waves ◽  
Tissue Fixation ◽  
Primary Method ◽  
Dipolar Molecules ◽  
Wide Range ◽  
Time Required ◽  
Cryostat Sections

Microwaves (MW) are electromagnetic waves which are commonly generated at a frequency of 2.45 GHz. When dipolar molecules such as water, the polar side chains of proteins and other molecules with an uneven distribution of electrical charge are exposed to such non-ionizing radiation, they oscillate through 180° at a rate of 2,450 million cycles/s. This rapid kinetic movement results in accelerated chemical reactions and produces instantaneous heat. MWs have recently been applied to a wide range of procedures for light microscopy. MWs generated by domestic ovens have been used as a primary method of tissue fixation, it has been applied to the various stages of tissue processing as well as to a wide variety of staining procedures. This use of MWs has not only resulted in drastic reductions in the time required for tissue fixation, processing and staining, but have also produced better cytologic images in cryostat sections, and more importantly, have resulted in better preservation of cellular antigens.

TIME TO THE END OF PRIMARY CONSOLIDATION (EOP) OF SOFT CLAYEY SOILS: CONCERNING THE EFFECT OF ATTERBERG’S LIMIT AND CYCLIC LOADING HISTORY

2019 ◽  
Vol 128 (2B) ◽  
pp. 29-41
Author(s):  
Trần Thanh Nhàn
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Clayey Soils ◽  
Loading History ◽  
Cyclic Shear ◽  
Wide Range ◽  
Primary Consolidation ◽  
Time Required

In order to observe the end of primary consolidation (EOP) of cohesive soils with and without subjecting to cyclic loading, reconstituted specimens of clayey soils at various Atterberg’s limits were used for oedometer test at different loading increments and undrained cyclic shear test followed by drainage with various cyclic shear directions and a wide range of shear strain amplitudes. The pore water pressure and settlement of the soils were measured with time and the time to EOP was then determined by different methods. It is shown from observed results that the time to EOP determined by 3-t method agrees well with the time required for full dissipation of the pore water pressure and being considerably larger than those determined by Log Time method. These observations were then further evaluated in connection with effects of the Atterberg’s limit and the cyclic loading history.

Quality Analysis of Fresh Cheese Prepared Using Wrightia tinctoria Proteases

2020 ◽  
Vol 16 (9) ◽  
pp. 1309-1317
Author(s):  
Anusha Rajagopalan ◽  
Bindhu O. Sukumaran
Keyword(s):  
Textural Properties ◽  
Artemia Salina ◽  
Quality Analysis ◽  
Human Consumption ◽  
Cheese Making ◽  
Phase Partitioning ◽  
Milk Clotting ◽  
Three Phase ◽  
Fresh Cheese ◽  
Wrightia Tinctoria

Background: Aqueous leaf extract of Wrightia tinctoria has been in use for artisanal cheese preparation in diverse parts of India. Scientific validation behind the milk clotting potential of W. tinctoria stem proteases purified through three-phase partitioning (TPP) has been attempted. However, its contribution to cheese quality standards has not been tried yet. Objective: To evaluate the suitability of three-phase partitioned W. tinctoria (WT) stem proteases in fresh cheese making. Methods: Fresh cheese was prepared using W. tinctoria TPP proteases and its characteristics were compared with that of commercial plant milk coagulant, Enzeco® (CEz) and rennin (CRn). Yield, organoleptic and textural properties, total fat, protein and moisture content of all cheese were determined according to FSSAI standards. Toxicity of the TPP proteases was assessed on the shrimp model (Artemia salina egg and Litopenaeus vannamei post-larval shrimps). Results: TPP proteases were found to be non-toxic and safe for human consumption with no change in egg hatchability and survival of the shrimps in comparison to that of control. Cheese analysis results indicated perceptible resemblance in nutritional characteristics of WT cheese with control cheese. Yield, textural properties and organoleptic acceptance of WT cheese resembled more closely with that of CEz cheese. Conclusion: Observation from the study paves the way for the acceptance of W. tinctoria proteases as a suitable vegetable rennet for fresh cheese making.

scholarly journals Quadrature Voltage Compensation in the Isolated Multi-Modular Converter

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 529
Author(s):  
Cristian Verdugo ◽  
Jose Ignacio Candela ◽  
Pedro Rodriguez
Keyword(s):  
Control Strategy ◽  
Phase Voltage ◽  
Multilevel Converters ◽  
Photovoltaic Panels ◽  
Circulating Current ◽  
Three Phase ◽  
Voltage Compensation ◽  
Wide Range ◽  
Modular Converter ◽  
The Impact

Series connections of modules in cascaded multilevel converters are prone to power imbalances due to voltage differences on their DC side. When modules are connected to direct current (DC) sources, such as photovoltaic panels, the capability of withstanding power imbalances is crucial for generating the maximum power. In order to provide a possible solution for this requirement, this paper proposes a control strategy called Quadrature Voltage Compensation, which allows a wide range of power imbalances. The proposed control strategy regulates the power by introducing a circulating current between the arms and a phase angle in the output voltage. The impact of the circulating current and its effect on the phase voltage are studied. To highlight the features of the proposed strategy, an analytical model based on vector superposition is also described, demonstrating the strong capability of tolerating power differences. Finally, to validate the effectiveness of the Quadrature Voltage Compensation, simulation and experimental results are presented for a three-phase isolated multi-modular converter.

scholarly journals Mass and Heat Transfer Coefficients in Automotive Exhaust Catalytic Converter Channels

Catalysts ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 507
Author(s):  
Chrysovalantis C. Templis ◽  
Nikos G. Papayannakos
Keyword(s):  
Heat Transfer ◽  
Flow Reactor ◽  
Catalytic Converter ◽  
Reaction Rates ◽  
Cfd Model ◽  
Automotive Exhaust ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Wide Range ◽  
Mass And Heat Transfer

Mass and heat transfer coefficients (MTC and HTC) in automotive exhaust catalytic monolith channels are estimated and correlated for a wide range of gas velocities and prevailing conditions of small up to real size converters. The coefficient estimation is based on a two dimensional computational fluid dynamic (2-D CFD) model developed in Comsol Multiphysics, taking into account catalytic rates of a real catalytic converter. The effect of channel size and reaction rates on mass and heat transfer coefficients and the applicability of the proposed correlations at different conditions are discussed. The correlations proposed predict very satisfactorily the mass and heat transfer coefficients calculated from the 2-D CFD model along the channel length. The use of a one dimensional (1-D) simplified model that couples a plug flow reactor (PFR) with mass transport and heat transport effects using the mass and heat transfer correlations of this study is proved to be appropriate for the simulation of the monolith channel operation.

Ensemble Learning Approach with LASSO for Predicting Catalytic Reaction Rates

Synlett ◽  
2020 ◽  
Author(s):  
Akira Yada ◽  
Kazuhiko Sato ◽  
Tarojiro Matsumura ◽  
Yasunobu Ando ◽  
Kenji Nagata ◽  
...  
Keyword(s):  
Ensemble Learning ◽  
Reaction Rates ◽  
Initial Reaction Rate ◽  
Training Dataset ◽  
Initial Reaction ◽  
Learning Approach ◽  
Learning Framework ◽  
Machine Learning Approach ◽  
Reasonable Prediction ◽  
Epoxidation Of Alkenes

AbstractThe prediction of the initial reaction rate in the tungsten-catalyzed epoxidation of alkenes by using a machine learning approach is demonstrated. The ensemble learning framework used in this study consists of random sampling with replacement from the training dataset, the construction of several predictive models (weak learners), and the combination of their outputs. This approach enables us to obtain a reasonable prediction model that avoids the problem of overfitting, even when analyzing a small dataset.

Analysis and Reduction of the Waste in the Work Process Using Time Study Analysis: A Case Study

2014 ◽  
Vol 660 ◽  
pp. 971-975 ◽  
Author(s):  
Mohd Norzaim bin Che Ani ◽  
Siti Aisyah Binti Abdul Hamid
Keyword(s):  
Cycle Time ◽  
Lean Manufacturing ◽  
Value Added ◽  
Time Study ◽  
Study Approach ◽  
Root Cause ◽  
Wide Range ◽  
Unit Of Work ◽  
Time Required ◽  
The Impact

Time study is the process of observation which concerned with the determination of the amount of time required to perform a unit of work involves of internal, external and machine time elements. Originally, time study was first starting to be used in Europe since 1760s in manufacturing fields. It is the flexible technique in lean manufacturing and suitable for a wide range of situations. Time study approach that enable of reducing or minimizing ‘non-value added activities’ in the process cycle time which contribute to bottleneck time. The impact on improving process cycle time for organization that it was increasing the productivity and reduce cost. This project paper focusing on time study at selected processes with bottleneck time and identify the possible root cause which was contribute to high time required to perform a unit of work.

Sign in / Sign up

Export Citation Format

Share Document