scholarly journals Effective Biosorption of Nickel(II) from Aqueous Solutions UsingTrichoderma viride

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
P. Sujatha ◽  
V. Kalarani ◽  
B. Naresh Kumar
Keyword(s):  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Trichoderma Viride ◽  
Toxic Metal ◽  
Freundlich Isotherm ◽  
Recovery Process ◽  
Primary Objective ◽  
Ion Concentration ◽  
Isotherm Models

The primary objective of the present study is to evaluate the optimization conditions such as kinetic and equilibrium isotherm models involved in the removal of Ni(II) from the aqueous solutions byTrichoderma viride. The biosorbent was characterized by FTIR and SEM. The optimum biosorption conditions were determined as a function of pH, biomass dosage, contact time, initial metal ion concentration, and temperature. The maximum Ni(II) biosorption was obtained at pH 4.5. The equilibrium data were better fit by the Langmuir isotherm model than by the Freundlich isotherm. The kinetic studies indicate that the biosorption process of the metal ion Ni(II) has followed well the pseudo-second-order model. The sum of the square errors (SSE) and chi-square (χ2) tests were also carried out to find the best fit kinetic model and adsorption isotherm. The maximum biosorption capacity (qm) ofT.viridebiomass was found to be 47.6 mg/g for Ni(II) ion. Therefore, it can be concluded thatT.viridebiomass was effective and low-cost potential adsorbent to remove the toxic metal Ni(II) from aqueous solutions. The recovery process of Ni(II) fromT.viridebiomass was found to be higher than 98% by using 0.25 M HNO3. Besides the application of removal of toxic metal Ni(II) from aqueous solutions, the biosorbentT.viridecan be reused for five consecutive sorption-desorption cycles was determined.

scholarly journals Studies on Removal of Cr (VI) from Aqueous Solutions Using Powder of Mosambi Fruit Peelings (PMFP) As a Low Cost Sorbent

2012 ◽  
Vol 9 (3) ◽  
pp. 1389-1399 ◽  
Author(s):  
R. Hema Krishna ◽  
A. V. V. S. Swamy
Keyword(s):  
Particle Size ◽  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Batch Tests ◽  
Freundlich Adsorption Isotherm ◽  
Equilibrium Data ◽  
Agitation Time

The powder of mosambi fruit peelings (PMFP) was used as an adsorbent for the removal of heavy metal like Cr (VI) from aqueous solutions was studied using batch tests. The influence of physico-chemical key parameters such as the initial metal ion concentration, pH, agitation time, adsorbent dosage, and the particle size of adsorbent has been considered in batch tests. Sorbent ability to adsorb Cr (VI) ions was examined and the mechanism involved in the process investigated. The optimum results were determined at an initial metal ion concentration was 10 mg/lit, pH=2, agitation time – 60 min, an adsorbent dose (150 mg/50 ml) and the particle size (0.6 mm). The % adsorption, Langmuir constants [Q0=7.51(mg/g) and b=1.69(mg/lit)] Freundlich constant(Kf=2.94), Lagergren rate constants (Kad(min-1)=5.75 x 10-2) for [Cr(VI)] 10 mg/lit were determined for the adsorption system as a function of sorbate concentration. The equilibrium data obtained were tested using Langmuir, Freundlich adsorption isotherm models, and the kinetic data obtained were fitted to pseudo first order model.

Removal of copper(II) and cadmium(II) ions from aqueous solutions by biosorption onto pine cone

2012 ◽  
Vol 66 (3) ◽  
pp. 564-572 ◽  
Author(s):  
Görkem Değirmen ◽  
Murat Kılıç ◽  
Özge Çepelioğullar ◽  
Ayşe E. Pütün
Keyword(s):  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Diffusion Kinetic ◽  
Biosorption Process ◽  
Biosorption Mechanism ◽  
Pine Cone ◽  
Pseudo Second Order

In this study, the removal of copper(II) and cadmium(II) ions from aqueous solutions by biosorption onto pine cone was studied. Variables that affect the biosorption process such as pH, biosorbent dosage, initial metal ion concentration, contact time and temperature of solution were optimized. Experimental data were fitted to Langmuir, Freundlich, Dubinin Radushkevich and Temkin isotherm models to investigate the equilibrium isotherms. Pseudo-first-order, pseudo-second-order and intraparticle diffusion kinetic models were used to determine the biosorption mechanism. The thermodynamics of biosorption were studied for predicting the nature of biosorption. Experimental results showed that pine cone could be evaluated as an alternative precursor for removal of heavy metal ions from aqueous solutions, due to its high biosorption capacity, availability, and low cost.

Moringa oleifera seeds for single and simultaneous removal of Pb2+ and Cd2+ from aqueous solutions

2020 ◽  
Author(s):  
Mohamed Abatal ◽  
Yaneth Stephanie Durán Avendaño ◽  
M. Teresa Olguin ◽  
Joel Vargas
Keyword(s):  
Aqueous Solutions ◽  
Metal Ion ◽  
Moringa Oleifera ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Sorption Data ◽  
Batch Tests ◽  
Pseudo Second Order

<p>In this study, we report the effectiveness of natural and NaOH treated Moringa oleifera seeds for single and simultaneous Pb<sup>2+ </sup>and Cd<sup>2+</sup> from aqueous solutions. The biosorbent was characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) techniques. The pH of point zero charge (pH<sub>pzc</sub>) was determined. Effects of contact time (15-1440 min), pH of solutions (2-10), mass of biosorbent (0.1-0.5 g) and initial metal ion concentration (10-1000 mg/L) were investigated using batch tests. The results show the pretreatment of biosorbent by NaOH improve significantly uptake capacity (mg/g) of the metal ions (q (Pb<sup>2+</sup>) = 38.45 and q (Cd<sup>2+</sup>) = 17.32 ˃ q (Pb<sup>2+</sup>) = 31.45 and q (Cd<sup>2+</sup>)= 14.67). Kinetic studies shown that the more than 90 % uptake of ion metals occurring within 120-180 min and the experimental data were better describe by a pseudo-second-order model. The sorption data for non-treated and NaOH treated Moringa oleifera seeds were evaluated by the Freundlich isotherm models to describe the adsorption equilibrium.</p>

scholarly journals Adsorption Study of Cu2+ Ions from Aqueous Solutions by Bael Flowers (Aegle marmelos)

2020 ◽  
Vol 11 (4) ◽  
pp. 11891-11904
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Low Cost ◽  
Sem Analysis ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Aegle Marmelos ◽  
Batch Mode ◽  
Initial Ph

In the present study, batch mode adsorption was carried out to investigate the adsorption capacity of dried bael flowers (Aegle marmelos) for the adsorptive removal of Cu(II) ions from aqueous solutions by varying agitation time, initial metal concentration, the dose of adsorbent, temperature, and initial pH of the Cu(II) ion solution. The percentage removal of 98.7% was observed at 50 ppm initial metal ion concentration, 0.5 g/100.00 cm3 adsorbent dosage, within the contact time of 120 minutes at 30 ºC in the pH range of 4 – 7. The sorption processes of Cu(II) ions was best described by pseudo-second-order kinetics. Langmuir isotherm had a good fit with the experimental data with 0.97 of correlation coefficient (R2), and the maximum adsorption capacity obtained was 23.14 mg g-1 at 30 ºC. The results obtained from sorption thermodynamic studies suggested that the adsorption process is exothermic and spontaneous. SEM analysis showed tubular voids on the adsorbent. FTIR studies indicated the presence of functional groups like hydroxyl, –C-O, –C=O, and amide groups in the adsorbent, which can probably involve in metal ion adsorption. Therefore, dried bael flowers can be considered an effective low-cost adsorbent for treating Cu(II) ions.

scholarly journals Adsorption of Cr6+ Onto Unmodified and Hydrochloric Acid Modified African Nutmeg Pod (Monodora myristica) from Aqueous Solution

2019 ◽  
pp. 1-8
Author(s):  
F. U. Okwunodulu ◽  
H. O. Chukwuemeka-Okorie ◽  
N. M. Mgbemena ◽  
J. B. I. Kalu
Keyword(s):  
Aqueous Solution ◽  
Metal Ion ◽  
Correlation Coefficients ◽  
Freundlich Isotherm ◽  
Low Ph ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Particle Sizes ◽  
Monodora Myristica ◽  
Best Fit

The removal of Cr6+ from aqueous solution using unmodified and hydrochloric modified African nutmeg pod was studied. The effects of particle size, pH and initial metal ions concentration adsorbed were investigated. The amount of metal ion adsorbed increased as the initial metal ion concentration increased and also decreased at low pH of 2 for both modified and unmodified African nutmeg pod.  400 µm and 250 µm were the optimum particle sizes for both modified and unmodified African nutmeg pod respectively, values given as 75.8 mg/g for the modified and 93.39 mg/g for the unmodified. Generally, it was observed that the unmodified African nutmeg pod showed greater adsorption capacity than the modified African nutmeg pod. The equilibrium experimental data were examined via Langmuir and Freundlich isotherm models.  Freundlich isotherm model gave the best fit for the data in both unmodified and modified African nutmeg pod based on the correlation coefficients (R2 values) gotten. The results of the study showed that the African nutmeg pod is efficient for the removal of Cr6+ from aqueous solutions especially when unmodified.

Removal of Pb(II) and Cd(II) From Aqueous Solution by Adsorption Using Agrowaste-Modified Kaolinite Clay

2021 ◽  
Keyword(s):  
Aqueous Solution ◽  
Aqueous Solutions ◽  
Metal Ions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Kaolinite Clay ◽  
Adsorbent Surface ◽  
Initial Adsorption ◽  
Adsorption Rates

This study showed that kaolinite clay modified with Moringa oleifera pods is a promising low cost adsorbent for the removal of metals from aqueous solution because the resultant composite has higher adsorption capacities, and hence a better metal ions removal efficiency. The efficiencies of these adsorbents for the removal of Pb (II) and Cd (II) ions from aqueous solutions were studied as a function of pH, time, adsorbate concentration and adsorbent dose. Adsorption results showed that pH did significantly affect removal of heavy metal ions between pH 3 and 6. Increasing contact time and initial metal ion concentration increased the sorption capacity of the adsorbent for the metal ions. Adsorbent dosage indicated mainly surface phenomena involving sharing of electrons between the adsorbent surface and the metal ion species. The adsorption of metal ions from aqueous solutions of both metal ions at different initial metal ion concentrations reduced the initial adsorption rates of the adsorption of Pb (II) and Cd (II) by unmodified and modified kaolinite clay.

scholarly journals Adsorption Behaviour of La(III) and Eu(III) Ions from Aqueous Solutions by Hydroxyapatite: Kinetic, Isotherm, and Thermodynamic Studies

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
F. Granados-Correa ◽  
J. Vilchis-Granados ◽  
M. Jiménez-Reyes ◽  
L. A. Quiroz-Granados
Keyword(s):  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Intraparticle Diffusion ◽  
Ion Concentration ◽  
Adsorption Behaviour ◽  
Freundlich Model ◽  
Adsorption Data ◽  
Isotherm Adsorption ◽  
Pseudo Second Order

The hydroxyapatite was successfully synthesized, characterized, and used as an alternative low-cost adsorbent material to study the adsorption behavior of La(III) and Eu(III) ions from nitrate aqueous solutions as a function of contact time, initial metal ion concentration, pH, and temperature by using a bath technique. The kinetic data correspond very well to the pseudo-second-order equation, and in both cases the uptake was affected by intraparticle diffusion. Isotherm adsorption data were well fitted by the Freundlich model equation with1/n>1, indicating a multilayer and cooperative-type adsorption. Thermodynamic parameters for the adsorption systems were determinated at 293, 303, 313, and 323 K. These parameters show that adsorptions of La(III) and Eu(III) ions on hydroxyapatite are endothermic and spontaneous processes. The adsorption was found to follow the order Eu(III) > La(III) and is dependent on ion concentration, pH, and temperature.

scholarly journals Utilization of Activated Carbon Prepared from Industrial Solid Waste for the Removal of Chromium(VI) Ions from Synthetic Solution and Industrial Effluent

2005 ◽  
Vol 23 (2) ◽  
pp. 145-160 ◽  
Author(s):  
N. Vennilamani ◽  
K. Kadirvelu ◽  
Y. Sameena ◽  
S. Pattabhi
Keyword(s):  
Activated Carbon ◽  
Metal Ion ◽  
Industrial Effluent ◽  
Carbon Adsorbent ◽  
Freundlich Isotherm ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Adsorption Sites ◽  
Chromium Vi ◽  
Sago Waste

Activated carbon (AC) prepared from sago waste was characterized and used to remove chromium(VI) ions from aqueous solution and industrial effluent by adsorption methods using various conditions of agitation time, metal ion concentration, adsorbent dosage particle size and pH. Surface modification of the carbon adsorbent with a strong oxidizing agent like concentrated H2SO4 generates more active adsorption sites on the solid surface and pores for metal ion adsorption. Adsorption of the metal ion required a very short time and led to quantitative removal. Both the Langmuir and Freundlich isotherm models could describe the adsorption data. The calculated values of Q0 and b were 5.78 mg/g and 1.75 1/min, respectively. An effective adsorption capacity was noted for particle sizes in the range 125–250 μm at room temperature (30 ± 2°C) and an initial pH of 2.0 ± 0.2. The specific surface area of the activated carbon was determined and its properties studied by scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR). These studies revealed that AC prepared from sago waste is suitable for the removal of Cr(VI) ions from both synthetic and industrial effluents.

scholarly journals Adsorption of Nickel Ion by Low Cost Carbon-Kinetic, Thermodynamic and Equilibrium Studies

2009 ◽  
Vol 6 (s1) ◽  
pp. S347-S357 ◽  
Author(s):  
V. Vijayakumaran ◽  
S. Arivoli ◽  
S. Ramuthai
Keyword(s):  
Langmuir Isotherm ◽  
Metal Ion ◽  
Low Cost ◽  
Mineral Acid ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Equilibrium Studies ◽  
Nickel Ion ◽  
Nickel Ions ◽  
Initial Ph

A carbonaceous adsorbent prepared from an indigenous waste, by acid treatment was tested for its efficiency in removing nickel ion. The process parameters studied include agitation time, initial metal ion concentration, carbon dose, pH and temperature. The adsorption followed first order reaction equation and the rate is mainly controlled by intraparticle diffusion. Freundlich and Langmuir isotherm models were applied to the equilibrium data. The adsorption capacity (Qm) obtained from the Langmuir isotherm plot were found to around 43 mg/g at an initial pH of 7.0. The temperature variation study showed that the nickel ions adsorption is endothermic and spontaneous with increased randomness at the solid solution interface. Significant effect on adsorption was observed on varying the pH of the nickel ion solutions. The Langmuir and Freundlich adsorption isotherms obtained, positive ΔH0value, pH dependent results and desorption of metal ions in mineral acid suggest that the adsorption of nickel ion on MCC involves chemisorption as well as physisorption mechanism.

scholarly journals Adsorption of Cr(Vi) Ion from Aqueous Solutions by Solid Waste of Potato Peels

2017 ◽  
Vol 5 (3) ◽  
pp. 254 ◽  
Author(s):  
Nidhal M. Sher Mohammed ◽  
Haydar A. Mohammad Salim
Keyword(s):  
Aqueous Solutions ◽  
Metal Ion ◽  
High Efficiency ◽  
Low Cost ◽  
Ion Concentration ◽  
Potato Peel ◽  
Order Model ◽  
Experimental Conditions ◽  
Langmuir Adsorption ◽  
Potato Peels

Pollution of wastewater with heavy metal has always been a serious problem to the environment. Chromium is considered one of the most noxious heavy metals. Adsorption is now reorganized as an alternative technology of defence for chromium removal due to local availability, technical efficiency and cost effectiveness. Potato peel powder can be used as a low cost biosorbent to remove hexavalent chromium from aqueous solutions under various experimental conditions. Different parameters including equilibrium contact time, initial metal ion concentration, potato peel dose, pH and temperature were studied through a number of batch sorption experiments. Both the Langmuir and Freundlich were found to fit the adsorption isotherm of Cr (VI) ion onto potato peel. The Langmuir adsorption capacity was found to be 1.97 mg/g while Freundlich constants including Kf and n were 1.57 and 2.5, respectively. The adsorption kinetic was found to be more fit with the pseudo-first order model. This study showed a high efficiency of potato peel for the biosorption of Cr (VI) ion from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document