scholarly journals Influence of Incorporation of Natural Fibers on the Physical, Mechanical, and Thermal Properties of Composites LDPE-Al Reinforced with Fique Fibers

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Miguel A. Hidalgo-Salazar ◽  
Mario F. Muñoz ◽  
José H. Mina
Keyword(s):  
Natural Fibers ◽  
Mechanical And Thermal Properties ◽  
Hot Press ◽  
Scanning Calorimetry ◽  
Aluminum Particles ◽  
Direct Function ◽  
Tetra Pak ◽  
Fique Fibers ◽  
The Impact ◽  
Properties Of Composites

This study shows the effect of the incorporation of natural fique fibers in a matrix formed by low-density polyethylene and aluminum (LDPE-Al) obtained in the recycling process of long-life Tetra Pak packaging. The reinforcement content was 10, 20, and 30% fibers, manufactured by hot-press compression molding of composite boards (LDPE-Al/fique). From the thermogravimetric analysis (TGA) it was determined that the proportions of the LDPE-Al were 75 : 25 w/w. Likewise, it was found that the aluminum particles increased the rigidity of the LDPE-Al, reducing the impact strength compared to LDPE recycled from Tetra Pak without aluminum; besides this, the crystallinity in the LDPE-Al increased with the presence of aluminum, which was observed by differential scanning calorimetry (DSC). The maximum strength and Young’s modulus to tensile and flexural properties increased with the incorporation of the fibers, this increase being a direct function of the amount of reinforcement contained in the material. Finally, a reduction in the density of the compound by the generation of voids at the interface between the LDPE-Al and fique fibers was identified, and there was also a greater water absorption due to weak interphase fiber-matrix and the hydrophilic fibers contained in the material.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Mechanical and Thermal Properties of Rubber Toughened Carbon Black-Filled Polyester Composite

2013 ◽  
Vol 812 ◽  
pp. 163-168 ◽  
Author(s):  
Mohd Redzuan Aein Afina ◽  
Bonnia Noor Najmi ◽  
Shuhaimen Siti Shakirah ◽  
Siti Norasmah Surip
Keyword(s):  
Thermal Properties ◽  
Carbon Black ◽  
Unsaturated Polyester ◽  
Impact Testing ◽  
Mechanical And Thermal Properties ◽  
Heat Flow Rate ◽  
Scanning Calorimetry ◽  
Rubber Toughened ◽  
Polyester Composite ◽  
The Impact

The influences of Carbon Black (CB) as filler for rubber toughened polyester composite on thermal properties were investigated, in consideration for applications such as automotive parts and integrated circuits (IC) encapsulations. The usage of CB as filler is one of the efforts in increasing and varying the use of rubber and unsaturated polyester thermoset in composite materials. Unsaturated polyester was mixed with 3% liquid natural rubber (LNR) as toughening agent and CB, which were varied from 0, 2, 4, 6, 8, and 10% using mechanical stirrer and moulded by using the open mould technique. Impact testing was conducted for mechanical property and it was found that the addition of CB increased the impact strength by 87%. Thermal properties of the composites were evaluated using a thermogravimetric analyzer (TGA) and differential scanning calorimetry (DSC). The TGA curves of the composites were quite similar, but there were slight increment in thermal stability for several CB filled composites compared to the neat polyester matrix. DSC analysis showed that all the composites were fully cured, and CB filled composites had a slower heat flow rate compared to the neat rubber toughened composite.

scholarly journals Effect of Content and Surface Modification of Fique Fibers on the Properties of a Low-Density Polyethylene (LDPE)-Al/Fique Composite

Polymers ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1050 ◽  
Author(s):  
Mario Muñoz-Vélez ◽  
Miguel Hidalgo-Salazar ◽  
Jose Mina-Hernández
Keyword(s):  
Surface Modification ◽  
Natural Fibers ◽  
Absorption Capacity ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Direct Function ◽  
Chemical Treatments ◽  
Fique Fibers ◽  
Mechanical Performances

This work presents the physical-thermal and mechanical characterization of a low-density polyethylene (LDPE)-Al matrix composite material that was obtained from reinforcing recycled (post-consumer) long-life Tetra Pak packages with fique natural fibers from southwestern Colombia. The fique was subjected to three chemical treatments to modify its surface (alkalinization, silanization and pre-impregnation with polyethylene) to increase the quality of its interfaces. Additionally, panels with 10%, 20%, and 30% v/v of fiber were manufactured by the hot compression molding. The mechanical properties of the different composite materials showed that the pre-impregnation treatment promoted a significant increase in the tensile and flexural properties with respect to the fiber-reinforced composite without surface modification. Additionally, in materials with 30% fibers that were treated with pre-impregnation, there was a decrease in the water absorption capacity of 53.15% when compared to composites made with 30% native fibers. Finally, increases in the fiber content mainly caused better mechanical performances, which increased as a direct function of the amount of fique incorporated.

Mechanical and thermal properties of polybutylene terephthalate/ethylene-vinyl acetate blends using vane extruder

e-Polymers ◽  
2018 ◽  
Vol 18 (1) ◽  
pp. 67-73 ◽  
Author(s):  
Cong Meng ◽  
Jin-ping Qu
Keyword(s):  
Impact Strength ◽  
Vinyl Acetate ◽  
Loss Modulus ◽  
Weight Fraction ◽  
Ethylene Vinyl Acetate ◽  
Mechanical Analysis ◽  
Mechanical And Thermal Properties ◽  
Polybutylene Terephthalate ◽  
Scanning Calorimetry ◽  
The Impact

AbstractThe poly(butylene terephthalate) (PBT)/ethylene-vinyl acetate copolymer (EVA) blends with different contents of EVA were prepared by an vane extruder. From the observation of morphologies, impact strength and dynamic mechanical analysis (DMA), the EVA particles were well dispersed in the PBT matrix and improved the impact strength of PBT. Differential scanning calorimetry measurements demonstrate that there is little diversification in the crystal structure and type. Thermogravimetric analysis reveals that as the weight fraction of EVA increases, the thermal stability of composite is enhanced. The rheological analyses indicate that the PBT/EVA blends follow a non-Newtonian behavior and viscosities of the blends are drastically lower than that of pure PBT at higher frequencies. The storage modulus (G′) and loss modulus (G″) of the blends monotonously increase as the frequency rises. This work provides a novel method to develop blends with excellent performance.

Thermal, morphological and mechanical properties of composites based on polyamide 6 with cellulose, silica and their hybrids from rice husk

2020 ◽  
pp. 002199832097829
Author(s):  
Renato P Melo ◽  
Marcelo P da Rosa ◽  
Paulo H Beck ◽  
Lucas GP Tienne ◽  
Maria de Fátima V Marques
Keyword(s):  
Mechanical Properties ◽  
Rice Husk ◽  
Natural Fibers ◽  
Polyamide 6 ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Cellulosic Fibers ◽  
The One ◽  
Properties Of Composites

The use of cellulosic fibers from different natural sources as fillers in polymer matrices to improve their properties has been extensively studied in the last years. It is mainly due to the vast availability of natural fibers as well as their biodegradability. The purpose of this present work was to extract cellulose, silica, and cellulose-silica fillers – these last called “hybrids” – from rice husk through delignification and subsequent oxidation and, then, prepare composites with polyamide 6 and improve mainly its thermal-mechanical properties. The content of 10 wt.% of fillers was inserted in PA 6 matrix. Infrared spectroscopy pointed the main characteristic peaks of cellulose and silica of hybrids, as thermogravimetric analysis showed high thermal stability of fillers, allowing their incorporation in PA-6 matrix by extrusion method. Thermo dynamic-mechanical analysis showed, in a general overview, a significant improvement of mechanical properties of composites, as elastic modulus, compared with neat polyamide-6, mainly the one with 2.5 wt% of silica and 7.5% of cellulose. This last also showed increasing of degree of crystallinity, measured by differential scanning calorimetry, showing the extraction efficiency of fillers from rice husk as well as the potential application of composites as structural components in automotive parts.

Characterization of Mechanical and Thermal Properties of PP/Mineral Composites

2014 ◽  
Vol 1025-1026 ◽  
pp. 241-245 ◽  
Author(s):  
Ľudmila Dulebová ◽  
Emil Spišák ◽  
Branislav Duleba ◽  
František Greškovič ◽  
Tomasz Garbacz
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Twin Screw ◽  
Pp Composites ◽  
Mineral Fillers ◽  
The Impact ◽  
Properties Of Composites

The paper presents the impact of the use of fillers on the mechanical properties of composites with polymeric matrix from polypropylene (PP). Two main types of mineral fillers - talc and calcium carbonate - were used for experiments. PP composites of different percentage filler in matrix PP were compounded with twin-screw extruder and then injection molding. Properties of composites were investigated by tensile test and thermal analysis. Tensile strength was performed to determine and compare the mechanical properties of the unfilled PP and filled PP with various percentages of fillers. Thermal analysis by thermogravimetric was performed on the tested materials - weight loss, glass transition temperature, thermal decomposition, melting temperature.

Mechanical and Thermal Properties of Reactable Nano-SiO2/polyoxymethylene Composites

2012 ◽  
Vol 535-537 ◽  
pp. 103-109 ◽  
Author(s):  
Xiang Min Xu ◽  
Li Ping Guo ◽  
Yu Dong Zhang ◽  
Zhi Jun Zhang
Keyword(s):  
Thermal Properties ◽  
Impact Strength ◽  
Decomposition Temperature ◽  
Silica Content ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Degradation Temperature ◽  
Melt Compounding ◽  
Air Atmosphere ◽  
The Impact

The polyoxymethylene-based composites containing reactable nano-SiO2were prepared in a twin-screw extruder by melt compounding, and mechanical and thermal properties of pure polyoxymethylene (POM) and composites were investigated. The results showed that reactable nano-SiO2could reinforce the tensile strength and Young’s modulus of composites. To the impact strength of composites, there was obvious improvement when a small amount of silica was added into POM. With the increase of silica content, the impact strength of composites showed a gradually decrease trend. It was worthy to note that reactable nano-SiO2could significantly increase the decomposition temperature of POM. When the content of reactaSubscript textble nano-SiO2was up to 5 wt%, the degradation temperature of composites could increase about 38.3°C under nSubscript textitrogen atmosphere and 43.8°C under air atmosphere, respectively, compared with pure POM. Furthermore, the differential scanning calorimetry (DSC) analysis showed that reactable nano-SiO2had a good heterogeneous nucleation capability in POM, and could increase crystallization temperature of POM, but surface structure of reactable nano-SiO2was not propitious to the growth of POM crystals, accordingly leading to the decreasing crystallinity of composites.

scholarly journals Effect of Polythiophene Content on Thermomechanical Properties of Electroconductive Composites

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2476
Author(s):  
Katarzyna Bednarczyk ◽  
Tomasz Kukulski ◽  
Ryszard Fryczkowski ◽  
Ewa Schab-Balcerzak ◽  
Marcin Libera
Keyword(s):  
Organic Solar Cells ◽  
Polyamide 6 ◽  
Thermomechanical Properties ◽  
Scanning Calorimetry ◽  
Good Thermal Stability ◽  
Mechanical And Electrical Properties ◽  
Ft Ir ◽  
Conductive Properties ◽  
The Impact ◽  
Properties Of Composites

The thermal, mechanical and electrical properties of polymeric composites combined using polythiophene (PT) dopped by FeCl3 and polyamide 6 (PA), in the aspect of conductive constructive elements for organic solar cells, depend on the molecular structure and morphology of materials as well as the method of preparing the species. This study was focused on disclosing the impact of the polythiophene content on properties of electrospun fibers. The elements for investigation were prepared using electrospinning applying two substrates. The study revealed the impact of the substrate on the conductive properties of composites. In this study composites exhibited good thermal stability, with T5 values in the range of 230–268 °C that increased with increasing PT content. The prepared composites exhibited comparable PA Tg values, which indicates their suitability for processing. Instrumental analysis of polymers and composites was carried out using Fourier Transform Infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM).

Mechanical and thermal properties of impact modified PBT blends and impact modified PBT nanocomposites

2013 ◽  
Vol 33 (6) ◽  
pp. 489-500 ◽  
Author(s):  
Ranjana Sharma ◽  
Purnima Jain ◽  
Susmita Dey Sadhu ◽  
Bikramjit Kaur
Keyword(s):  
Glycidyl Methacrylate ◽  
Breaking Strength ◽  
Tensile Modulus ◽  
Detailed Comparison ◽  
Mechanical And Thermal Properties ◽  
Melt Blending ◽  
Scanning Calorimetry ◽  
Cloisite 30B ◽  
The Impact ◽  
Ethylene Methyl Acrylate

Abstract Elastomer toughened poly(butylene terephthalate) (PBT)/organoclay [Cloisite 30B, organo-montmorillonite (OMMT)] nanocomposites were prepared via melt blending using a micro-compounder. In this work, two types of impact modifiers, ultra low density polyethylene grafted glycidyl methacrylate (ULDPE-g-GMA, IM1) and ethylene-methyl acrylate-glycidyl methacrylate (E-MA-GMA, IM2) were used, and a detailed comparison of the effect of both was made. With respect to the impact strength, 2 wt% of ULDPE-g-GMA produced a better result as compared to 2 wt% E-MA-GMA. Therefore, 2 wt% of ULDPE-g-GMA is considered as the optimized percentage for the preparation of nanocomposites. Being an impact modifier, ULDPE-g-GMA decreases the yield stress, tensile modulus and breaking strength of pure PBT. This issue was addressed in this paper by using organoclay, which may improve the tensile properties of PBT materials. The content of ULDPE-g-GMA was kept constant, whereas organoclay (OMMT) content was varied from 2 to 5 wt% in nanocomposites. The melting and crystallization behavior of pure PBT, impact modified PBT and its nanocomposites were studied by differential scanning calorimetry (DSC). Crystalline morphology was investigated using polarizing optical microscopy (POM) at 185°C, 195°C, and 205°C crystallization temperatures. The optimum increase in tensile modulus of the elastomer toughened PBT nanocomposites was seen with a 3 wt% addition of organoclay.

Sign in / Sign up

Export Citation Format

Share Document