scholarly journals Effect of Reynolds Number on Aerodynamics of Airfoil with Gurney Flap

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Shubham Jain ◽  
Nekkanti Sitaram ◽  
Sriram Krishnaswamy
Keyword(s):  
Reynolds Number ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Critical Range ◽  
Gurney Flap ◽  
Stall Angle ◽  
Lift And Drag ◽  
Naca 0012

Steady state, two-dimensional computational investigations performed on NACA 0012 airfoil to analyze the effect of variation in Reynolds number on the aerodynamics of the airfoil without and with a Gurney flap of height of 3% chord are presented in this paper. RANS based one-equation Spalart-Allmaras model is used for the computations. Both lift and drag coefficients increase with Gurney flap compared to those without Gurney flap at all Reynolds numbers at all angles of attack. The zero lift angle of attack seems to become more negative as Reynolds number increases due to effective increase of the airfoil camber. However the stall angle of attack decreased by 2° for the airfoil with Gurney flap. Lift coefficient decreases rapidly and drag coefficient increases rapidly when Reynolds number is decreased below critical range. This occurs due to change in flow pattern near Gurney flap at low Reynolds numbers.

Computational Study of Taper Effect of a Hydrofoil at Different Reynolds Numbers on the Length of Cavity and Lift and Drag Coefficients

2009 ◽  
Author(s):  
Mohammad J. Izadi ◽  
Mahdi Mirtorabi
Keyword(s):  
Reynolds Number ◽  
High Reynolds Number ◽  
Cavity Length ◽  
Computational Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
High Reynolds ◽  
Lift And Drag

In this paper a cavitating flow around a three dimensional tapered hydrofoil in an incompressible fluid is modeled and studied. The variables in this study are the taper ratio, angle of attack and the Reynolds number. The taper ratio changes from 0.2 to 1, the angles of attack varies from −2 to 12 degrees and all these are computed at two Reynolds numbers (Re = 5.791·107 and Re = 1.99·108). The flow is assumed to be unsteady and isothermal. Coefficients of drag and lift and also the cavity length are computed numerically. Comparing the numerical results of five investigated models (five tapered hydrofoils) and the work done by Kermeen experimentally, it can be seen that the tapered hydrofoil in some cases gave better results, reducing the cavity length and improving the lift coefficient. At the low Reynolds number, the length of the cavity is calculated to be small in comparison with the length gained at the high Reynolds number, and therefore the change of the taper and the angles of attack did change the amount of the lift coefficient as much. For high Reynolds number, as the angle of attack increased, the tapering effect became more important and the best lift coefficient and minimum cavity length is obtained at a taper ratio of 0.4 for an averaged angles of attack.

scholarly journals Experimental study of low Reynolds number effects on aerodynamics of smooth and sinusoidal leading-edge wings in the vicinity of the ground

2021 ◽  
Vol 15 (2) ◽  
pp. 8205-8218
Author(s):  
A. A. Mehraban ◽  
Mohammad Hassan Djavareshkian
Keyword(s):  
Reynolds Number ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Ground Clearance ◽  
Wide Range ◽  
Reynolds Number Effects ◽  
Low Reynolds ◽  
Stall Angle

Present study experimentally investigates the effects of ground clearance and Reynolds number on aerodynamic coefficients of smooth and sinusoidal leading-edge wings. Wind tunnel tests are conducted over a wide range of angles of attack from zero to 36 degrees, low Reynolds numbers of 30,000, 45,000 and 60,000, and also ground clearances of 0.5, 1 and ∞. Results showed that reduction of ground clearance and increment of Reynolds number cause the lift coefficient and the lift to drag ratio of both wings to be enhanced. Furthermore, the effects of Reynolds number and ground clearance on the smooth leading-edge wing are more than the sinusoidal leading-edge one. In addition, the sinusoidal leading-edge wing shows an excellent performance in the poststall region due to producing a higher lift and also by delaying the stall angle compared to the smooth leading-edge wing.

Low Reynolds number flow around and heat transfer from a heated circular cylinder

2010 ◽  
Vol 1 (1-2) ◽  
pp. 15-20 ◽  
Author(s):  
B. Bolló
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Reynolds Number Flow ◽  
Two Dimensional Flow ◽  
Number Flow ◽  
Low Reynolds ◽  
Increasing Temperature

Abstract The two-dimensional flow around a stationary heated circular cylinder at low Reynolds numbers of 50 < Re < 210 is investigated numerically using the FLUENT commercial software package. The dimensionless vortex shedding frequency (St) reduces with increasing temperature at a given Reynolds number. The effective temperature concept was used and St-Re data were successfully transformed to the St-Reeff curve. Comparisons include root-mean-square values of the lift coefficient and Nusselt number. The results agree well with available data in the literature.

scholarly journals Plunging Airfoil: Reynolds Number and Angle of Attack Effects

Aerospace ◽  
2021 ◽  
Vol 8 (8) ◽  
pp. 216
Author(s):  
Emanuel A. R. Camacho ◽  
Fernando M. S. P. Neves ◽  
André R. R. Silva ◽  
Jorge M. M. Barata
Keyword(s):  
Reynolds Number ◽  
High Performance ◽  
Angle Of Attack ◽  
Systems Design ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Low Reynolds Numbers ◽  
Operational Conditions ◽  
Naca0012 Airfoil ◽  
The Mean

Natural flight has consistently been the wellspring of many creative minds, yet recreating the propulsive systems of natural flyers is quite hard and challenging. Regarding propulsive systems design, biomimetics offers a wide variety of solutions that can be applied at low Reynolds numbers, achieving high performance and maneuverability systems. The main goal of the current work is to computationally investigate the thrust-power intricacies while operating at different Reynolds numbers, reduced frequencies, nondimensional amplitudes, and mean angles of attack of the oscillatory motion of a NACA0012 airfoil. Simulations are performed utilizing a RANS (Reynolds Averaged Navier-Stokes) approach for a Reynolds number between 8.5×103 and 3.4×104, reduced frequencies within 1 and 5, and Strouhal numbers from 0.1 to 0.4. The influence of the mean angle-of-attack is also studied in the range of 0∘ to 10∘. The outcomes show ideal operational conditions for the diverse Reynolds numbers, and results regarding thrust-power correlations and the influence of the mean angle-of-attack on the aerodynamic coefficients and the propulsive efficiency are widely explored.

An experimental investigation of the oscillating lift and drag of a circular cylinder shedding turbulent vortices

1961 ◽  
Vol 11 (2) ◽  
pp. 244-256 ◽  
Author(s):  
J. H. Gerrard
Keyword(s):  
Experimental Investigation ◽  
Reynolds Number ◽  
Circular Cylinder ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Circular Cylinders ◽  
Cylinder Surface ◽  
Fluctuating Pressure ◽  
Order Of Magnitude ◽  
Lift And Drag

The oscillating lift and drag on circular cylinders are determined from measurements of the fluctuating pressure on the cylinder surface in the range of Reynolds number from 4 × 103 to just above 105.The magnitude of the r.m.s. lift coefficient has a maximum of about 0.8 at a Reynolds number of 7 × 104 and falls to about 0.01 at a Reynolds number of 4 × 103. The fluctuating component of the drag was determined for Reynolds numbers greater than 2 × 104 and was found to be an order of magnitude smaller than the lift.

Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

scholarly journals An Experimental Analysis on the Effects of Stagger on the Aerodynamic Forces of Tandem Wings

AVIA ◽  
2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Y Parlindungan ◽  
S Tobing
Keyword(s):  
Experimental Analysis ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Performance ◽  
Open Loop ◽  
Aerodynamic Forces ◽  
Subsonic Wind Tunnel ◽  
Lift And Drag ◽  
Naca 0012

This study is inspired by the flapping motion of natural flyers: insects. Many insects have two pairs of wings referred as tandem wings. Literature review indicates that the effects of tandem wing are influenced by parameters such as stagger (the stream-wise distance between the aerodynamic center of the front and the rear airfoil), angle-of-attack and flow velocity. As a first stage, this study focuses on the effects of stagger (St) on the aerodynamic performance of tandem wings. A recent numerical study of stagger on tandem airfoils in turbulent flow (Re = 6000000) concluded that a larger stagger resulted in a decrease in lift force, and an increase in drag force. However, for laminar flow (Re = 2000), increasing the stagger was not found to be detrimental for aerodynamic performance. Another work also revealed that the maximum lift coefficient for a tandem configuration decreased with increasing stagger. The focus of this study is to perform an experimental analysis of tandem two-dimensional (2D) NACA 0012 airfoils. The two airfoils are set at the same angle-of-attack of 0° to 15° with 5° interval and three variations of stagger: 1c, 1.5c and 2c. The experiments are conducted using an open-loop-subsonic wind tunnel at a Reynolds number of 170000. The effects of St on the aerodynamic forces (lift and drag) are analyzed

Experimental investigations on the application of lift enhancement devices to forward-swept aircraft model

2006 ◽  
Vol 110 (1108) ◽  
pp. 361-367 ◽  
Author(s):  
W. Zhang ◽  
J. J. Wang ◽  
Z. Wu
Keyword(s):  
Lift Coefficient ◽  
Experimental Investigations ◽  
Aircraft Model ◽  
High Side ◽  
Gurney Flap ◽  
Lift Enhancement ◽  
Stall Angle ◽  
Lift And Drag ◽  
Low Speed Wind Tunnel ◽  
Wing Tip

Abstract The force measurements were conducted in low speed wind tunnel to investigate the effects of the scale, shape and the installation type of Gurney flap on a forward-swept aircraft model. The results indicated that both rectangular and triangular Gurney flaps can enhance the lift coefficient of the model tested, but with a little decrease of stall angle from 38° to 36°. The lift and drag coefficients increased with the Gurney flap scales. Meanwhile, the triangular Gurney flap can improve the aerodynamic performance more effectively when its high side is located near the wing root than the reverse installation with the low side near the wing root and the high side near the wing tip. Additionally, for the same Gurney flap, the model with smaller forward-swept angle can generate higher lift-enhancement in comparison with the larger forward-swept angle model.

Numerical investigation of the effect of triangular cavity on the unsteady aerodynamics of NACA 0012 at a low Reynolds number

2021 ◽  
pp. 095441002110270
Author(s):  
Rajesh Yadav ◽  
Aslesha Bodavula
Keyword(s):  
Reynolds Number ◽  
Steady State ◽  
Unsteady Aerodynamics ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Accurate Solution ◽  
Low Reynolds Numbers ◽  
State Regime ◽  
Low Reynolds ◽  
Naca 0012

Time accurate numerical simulations were conducted to investigate the effect of triangular cavities on the unsteady aerodynamic characteristics of NACA 0012 airfoil at a Reynolds number of 50,000. Right-angled triangular cavities are placed at 10%, 25% and 50% chord location on the suction and have depths of 0.025c and 0.05c, measured normal to the surface of the airfoil. The second-order accurate solution to the RANS equations is obtained using a pressure-based finite volume solver with a four-equation transition turbulence model, γ–Re θt, to model the effect of turbulence. The two-dimensional results suggest that the cavity of depth 0.025c at 10% chord improves the aerodynamic efficiency ( l/d ratio) by 52%, at an angle of attack of α = 8°, wherein the flow is steady. The shallower triangular cavity when placed at 25%c and 50%c enhances the l/d ratio by only 10% and 17%, respectively, in the steady-state regime of angles of attack between α = 6° and 10°. The deeper cavity also enhances the l/d ratio by up to 13%, 22% and 14% at angles of attack between α = 6° and 10°. Even in the unsteady vortex shedding regime, at α =12° and higher, significant improvements in the time-averaged l/d ratios are observed for both cavity depths. The improvements in l/d ratio in the steady-state, pre-stall regime are primarily because of drag reduction while in the post-stall, unsteady regime, the improvements are because of enhancements in time-averaged C l values. The current finding can thus be used to enhance the aerodynamic performance of MAVs and UAVs that fly at low Reynolds numbers.

Alula-Inspired Leading Edge Device for Low Reynolds Number Flight

2016 ◽  
Author(s):  
Boris A. Mandadzhiev ◽  
Michael K. Lynch ◽  
Leonardo P. Chamorro ◽  
Aimy A. Wissa
Keyword(s):  
Reynolds Number ◽  
Wind Tunnel ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Tip Vortex ◽  
Relative Angle ◽  
Lift And Drag

Robust and predictable aerodynamic performance of unmanned aerial vehicles at the limits of their design envelope is critical for safety and mission adaptability. In order for a fixed wing aircraft to maintain the lift necessary for sustained flight at very low speeds and large angles of attack (AoA), the wing shape has to change. This is often achieved by using deployable aerodynamic surfaces, such as flaps or slats, from the wing leading or trailing edges. In nature, one such device is a feathered structure on birds’ wings called the alula. The span of the alula is 5% to 20% of the wing and is attached to the first digit of the wing. The goal of the current study is to understand the aerodynamic effects of the alula on wing performance. A series of wind tunnel experiments are performed to quantify the effect of various alula deployment parameters on the aerodynamic performance of a cambered airfoil (S1223). A full wind tunnel span wing, with a single alula located at the wing mid-span is tested under uniform low-turbulence flow at three Reynolds numbers, Re = 85,000, 106,00 and 146,000. An experimental matrix is developed to find the range of effectiveness of an alula-type device. The alula relative angle of attack measured measured from the mean chord of the airfoil is varied to modulate tip-vortex strength, while the alula deflection is varied to modulate the distance of the tip vortex to the wing surface. Lift and drag forces were measured using a six axis force transducer. The lift and drag coefficients showed the greatest sensitivity to the the alula relative angle of attack, increasing the normalized lift coefficient by as much as 80%. Improvements in lift are strongly correlated to higher alula angle, with β = 0° – 5°, while reduction in the drag coefficient is observed with higher alula tip deflection ratios and lower β angles. Results show that, as the wing angle of attack and Reynolds number are increased, the overall lift co-efficient improvement is diminished while the reduction in drag coefficient is higher.

Sign in / Sign up

Export Citation Format

Share Document