Synthesis of a Novel Ce-bpdc for the Effective Removal of Fluoride from Aqueous Solution

Ce-1,1′-biphenyl-4,4′-dicarboxylic acid (Ce-bpdc), a novel type of metal organic framework, was synthesized and applied to remove excessive fluoride from water. The structure and morphology of Ce-bpdc were measured by X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The effects, such as saturated adsorption capacity, HCO3-, and pH, were investigated. The optimal pH value for fluoride adsorption was the range from 5 to 6. The coexisting bicarbonate anions have a little influence on fluoride removal. The fluoride adsorption over the Ce-bpdc adsorbent could reach its equilibrium in about 20 min. The Ce-bpdc coordination complex exhibited high binding capacity for fluoride ions. The maximum adsorption capacity calculated from Langmuir model was high up to 45.5 mg/g at 298 K (pH = 7.0) and the removal efficiency was greater than 80%. In order to investigate the mechanism of fluoride removal, various adsorption isotherms such as Langmuir and Freundlich were fitted. The experimental data revealed that the Langmuir isotherm gave a more satisfactory fit for fluoride removal. Finally, the tested results of ground water samples from three places, Yuefang, Jiangji, and Sanyi which exhibited high removal efficiency, also demonstrate the potential utility of the Ce-bpdc as an effective adsorbent.

Download Full-text

Mg-Al Mixed Oxide Adsorbent Synthesized Using FCT Template for Fluoride Removal from Drinking Water

Bioinorganic Chemistry and Applications ◽

10.1155/2019/5840205 ◽

2019 ◽

Vol 2019 ◽

pp. 1-11 ◽

Cited By ~ 3

Author(s):

Jifa Liu ◽

Ping Zhao ◽

Yue Xu ◽

Xibin Jia

Keyword(s):

Drinking Water ◽

Adsorption Capacity ◽

Mixed Oxide ◽

Photoelectron Spectroscopy ◽

Raw Materials ◽

Molar Ratio ◽

Fluoride Removal ◽

Hydroxyl Groups ◽

X Ray ◽

Fluoride Adsorption

To make full use of natural waste, a novel Mg-Al mixed oxide adsorbent was synthesized by the dip-calcination method using the fluff of the chinar tree (FCT) and an Mg(II) and Al(III) chloride solution as raw materials. The adsorbents were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The effects of the Mg/Al molar ratio and calcination temperature on the performance of the novel Mg-Al mixed oxide adsorbent were investigated. The optimized Mg-Al mixed oxide adsorbent had a Langmuir adsorption capacity of 53 mg/g. This adsorption capacity was higher than that of the separate Mg oxide and Al oxide. The synergy between Mg and Al is beneficial to the adsorption performance of the material. The fluoride adsorption capacity of the optimized Mg-Al mixed oxide adsorbent is only slightly affected by ions such as Cl−, NO3−, SO42−, Na+, and K+and is excellent for use in recycling and real water. The hydroxyl groups on the surface of the Mg-Al mixed oxide adsorbent play a key role in the adsorption of fluorine. The as-obtained novel Mg-Al mixed oxide adsorbent is an efficient and environmentally friendly agent for fluoride removal from drinking water.

Download Full-text

Pristine and Magnetic Kenaf Fiber Biochar for Cd2+ Adsorption from Aqueous Solution

International Journal of Environmental Research and Public Health ◽

10.3390/ijerph18157949 ◽

2021 ◽

Vol 18 (15) ◽

pp. 7949

Author(s):

Anwar Ameen Hezam Saeed ◽

Noorfidza Yub Harun ◽

Suriati Sufian ◽

Muhammad Roil Bilad ◽

Zaki Yamani Zakaria ◽

...

Keyword(s):

Adsorption Capacity ◽

Photoelectron Spectroscopy ◽

Textural Properties ◽

Ion Concentration ◽

Solution Temperature ◽

Maximum Adsorption Capacity ◽

Magnetic Biochar ◽

X Ray ◽

Study Results ◽

Capacity Surface

Development of strategies for removing heavy metals from aquatic environments is in high demand. Cadmium is one of the most dangerous metals in the environment, even under extremely low quantities. In this study, kenaf and magnetic biochar composite were prepared for the adsorption of Cd2+. The synthesized biochar was characterized using (a vibrating-sample magnetometer VSM), Scanning electron microscopy (SEM), X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The adsorption batch study was carried out to investigate the influence of pH, kinetics, isotherm, and thermodynamics on Cd2+ adsorption. The characterization results demonstrated that the biochar contained iron particles that help in improving the textural properties (i.e., surface area and pore volume), increasing the number of oxygen-containing groups, and forming inner-sphere complexes with oxygen-containing groups. The adsorption study results show that optimum adsorption was achieved under pH 5–6. An increase in initial ion concentration and solution temperature resulted in increased adsorption capacity. Surface modification of biochar using iron oxide for imposing magnetic property allowed for easy separation by external magnet and regeneration. The magnetic biochar composite also showed a higher affinity to Cd2+ than the pristine biochar. The adsorption data fit well with the pseudo-second-order and the Langmuir isotherm, with the maximum adsorption capacity of 47.90 mg/g.

Download Full-text

Fabrication of Carboxymethylcellulose/Metal-Organic Framework Beads for Removal of Pb(II) from Aqueous Solution

Materials ◽

10.3390/ma12060942 ◽

2019 ◽

Vol 12 (6) ◽

pp. 942 ◽

Cited By ~ 10

Author(s):

Huo-Xi Jin ◽

Hong Xu ◽

Nan Wang ◽

Li-Ye Yang ◽

Yang-Guang Wang ◽

...

Keyword(s):

Aqueous Solutions ◽

Adsorption Capacity ◽

Photoelectron Spectroscopy ◽

Langmuir Isotherm ◽

Adsorption Equilibrium ◽

Isotherm Model ◽

Maximum Adsorption Capacity ◽

X Ray ◽

Metal Organic ◽

Langmuir Isotherm Model

The ability to remove toxic heavy metals, such as Pb(II), from the environment is an important objective from both human-health and ecological perspectives. Herein, we describe the fabrication of a novel carboxymethylcellulose-coated metal organic material (MOF-5–CMC) adsorbent that removed lead ions from aqueous solutions. The adsorption material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, and X-ray photoelectron spectroscopy. We studied the functions of the contact time, pH, the original concentration of the Pb(II) solution, and adsorption temperature on adsorption capacity. MOF-5–CMC beads exhibit good adsorption performance; the maximum adsorption capacity obtained from the Langmuir isotherm-model is 322.58 mg/g, and the adsorption equilibrium was reached in 120 min at a concentration of 300 mg/L. The adsorption kinetics is well described by pseudo-second-order kinetics, and the adsorption equilibrium data are well fitted to the Langmuir isotherm model (R2 = 0.988). Thermodynamics experiments indicate that the adsorption process is both spontaneous and endothermic. In addition, the adsorbent is reusable. We conclude that MOF-5–CMC is a good adsorbent that can be used to remove Pb(II) from aqueous solutions.

Download Full-text

Adsorption of hexavalent chromium by polyacrylonitrile-based porous carbon from aqueous solution

Royal Society Open Science ◽

10.1098/rsos.171662 ◽

2018 ◽

Vol 5 (1) ◽

pp. 171662 ◽

Cited By ~ 14

Author(s):

Bin Feng ◽

Wenzhong Shen ◽

Liyi Shi ◽

Shijie Qu

Keyword(s):

Aqueous Solution ◽

Adsorption Capacity ◽

Porous Carbon ◽

Photoelectron Spectroscopy ◽

Ph Value ◽

Functional Materials ◽

High Specific Surface Area ◽

Maximum Adsorption Capacity ◽

Elementary Analysis ◽

Initial Adsorption

Owing to the unique microporous structure and high specific surface area, porous carbon could act as a good carrier for functional materials. In this paper, polyacrylonitrile (PAN)-based porous carbon materials (PPC-0.6-600, PPC-0.8-600, PPC-0.6-800 and PPC-0.8-800) were prepared by heating KOH at 600°C and 800 o C for the removal of Cr(VI) from aqueous solution. The adsorbent was characterized by the techniques of Fourier transform infrared spectroscopy (FT-IR), elementary analysis, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and N 2 adsorption techniques. The results showed that the adsorption capacity increased with decreasing pH value of the initial solution. The adsorption capacity of Cr(VI) on PPC-0.8-800 was much greater than that on other materials, and maximum adsorption capacity were calculated to be 374.90 mg g −1 . Moreover, PPC-0.8-800 had superior recyclability for the removal of Cr(VI) from wastewater, about 82% of its initial adsorption capacity was retained even after five cycles. The result of kinetic simulation showed that the adsorption of Cr(VI) on the PAN-based porous carbon could be described by pseudo-second-order kinetics. The adsorption process was the ionic interaction between protonated amine groups of PPC and HCrO 4 - ions.

Download Full-text

Mechanochemically Activated Aluminosilicate Clay Soils and their Application for Defluoridation and Pathogen Removal from Groundwater

International Journal of Environmental Research and Public Health ◽

10.3390/ijerph16040654 ◽

2019 ◽

Vol 16 (4) ◽

pp. 654 ◽

Cited By ~ 4

Author(s):

Olumuyiwa Obijole ◽

Mugera Gitari ◽

Patrick Ndungu ◽

Amidou Samie

Keyword(s):

Clay Soils ◽

Diffusion Method ◽

Fluoride Removal ◽

Particle Diffusion ◽

Maximum Adsorption Capacity ◽

Bacterial Strains ◽

Pathogen Removal ◽

X Ray ◽

Fluoride Adsorption ◽

Bet Analysis

In this study, aluminosilicate rich clay soils were prepared through mechanochemical activation. The chemical and mineralogical properties were investigated using X-Ray Fluorescence (XRF) and X-ray diffraction (XRD). The functional groups, morphology and surface area were evaluated using Fourier Transform Infra-Red (FTIR), Scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. Batch experiments were used to evaluate its defluoridation efficiency while antibacterial activities were assessed using well diffusion method. Maximum adsorption capacity was found to be 1.87 mg/g with 32% fluoride removal. Fluoride adsorption was found to reduce in the presence of Cl−, PO42− and CO32− while it increased in the presence of SO42− and NO3−. Adsorption data fitted well to Freundlich isotherms, hence, confirming heterogeneous multilayer adsorption. Kinetic studies revealed that fluoride adsorption fitted well to pseudo-second order model. The sorption of F− onto the clays’ surface followed intra-particle diffusion mode. High correlation coefficient indicates that the sorption process was greatly controlled by particle diffusion while it is minimal in pore diffusion model. Antibacterial studies revealed no zone of inhibition for all the activated clays, hence indicating that they are not active against the bacterial strains of Escherichia coli used in this study. The results showed activated clays’ potential for defluoridation. Its effectiveness in pathogen removal is limited. Hence further modifications of the clays’ surfaces are hereby recommended.

Download Full-text

β-Cyclodextrin Modified Poly(Acrylonitrule-co-Acrylic Acid) Hydrogel for Thorium(IV) Adsorption

Polymers ◽

10.3390/polym9060201 ◽

2017 ◽

Vol 9 (6) ◽

pp. 201 ◽

Cited By ~ 19

Author(s):

Guojian Duan ◽

Qiangqiang Zhong ◽

Lei Bi ◽

Liu Yang ◽

Tonghuan Liu ◽

...

Keyword(s):

Adsorption Capacity ◽

Contact Time ◽

Ph Value ◽

Water System ◽

Maximum Adsorption Capacity ◽

Practical Application ◽

X Ray Diffraction ◽

Liquid Ratio ◽

X Ray ◽

Solid Liquid

In this report, the β-CD(AN-co-AA) hydrogel was used to remove the thorium(IV) [Th(IV)] from the water system, and the new adsorbent was characterized through Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The influences of contact time, pH value, ionic strength, solid-liquid ratio, initial Th(IV) concentration, and temperature on Th(IV) adsorption onto the functional hydrogel were researched. The results showed that the experimental data followed the Langmuir isotherm and the maximum adsorption capacity (qmax) for Th(IV) was 692 mg/g at pH 2.95, which approached the calculated (qe) 682 mg/g. The desorption capacity of Th(IV) in different HNO3 concentrations ranging from 0.005 to 0.5 M was also studied, and the percentage of the maximum desorption was 86.85% in the condition of 0.09 M HNO3. The selectivity of β-CD(AN-co-AA) hydrogel was also be studied, the results indicated that this material retained the good adsorption capacity to Th(IV) even when the Ca2+, Mg2+, or Pb2+ existed in the system. The findings indicate that β-CD(AN-co-AA) can be used as a new candidate for the enrichment and separation of Th(IV), or its analogue actinides, from large-volume solution in practical application.

Download Full-text

Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

10.21203/rs.3.rs-191207/v1 ◽

2021 ◽

Author(s):

You Wu ◽

Zuannian Liu ◽

Bakhtari Mohammad Fahim ◽

Junnan Luo

Keyword(s):

Adsorption Capacity ◽

Photoelectron Spectroscopy ◽

Adsorption Mechanism ◽

Nitrogen Adsorption ◽

Adsorption Properties ◽

Maximum Adsorption Capacity ◽

X Ray Diffraction ◽

X Ray ◽

Adsorption Mechanisms ◽

Adsorption Desorption

Abstract In this study, MIL-101(Fe), MIL-101(Fe,Cu), and Graphene Oxide (GO) /MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOFs-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including reaction time, pH, temperature and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g− 1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m2/g is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe),which are 747.75 and 510.66m2/g respectively. The adsorption mechanism of phosphate is electrostatic attraction, form coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

Download Full-text

Investigation of kinetics and adsorption isotherm for fluoride removal from aqueous solutions using mesoporous cerium–aluminum binary oxide nanomaterials

RSC Advances ◽

10.1039/d1ra00598g ◽

2021 ◽

Vol 11 (46) ◽

pp. 28744-28760

Author(s):

Rumman Zaidi ◽

Saif Ullah Khan ◽

I. H. Farooqi ◽

Ameer Azam

Keyword(s):

Adsorption Isotherm ◽

Aqueous Solutions ◽

Adsorption Capacity ◽

Surface Area ◽

Removal Efficiency ◽

Small Dose ◽

Binary Oxide ◽

Fluoride Removal ◽

Maximum Adsorption Capacity

Mesoporous Ce–Al binary oxide nanomaterials prepared with a surface area of 110.32 m2 g−1 showed defluoridation capacity at pH 2.4, exhibited maximum adsorption capacity of 384.6 mg g−1 and a removal efficiency of 91.5% at a small dose of nanoadsorbent.

Download Full-text

Synthesis of magnetic biochar derived from cotton stalks for the removal of Cr(VI) from aqueous solution

Water Science & Technology ◽

10.2166/wst.2019.208 ◽

2019 ◽

Vol 79 (11) ◽

pp. 2106-2115 ◽

Cited By ~ 3

Author(s):

Fengfeng Ma ◽

Baowei Zhao ◽

Jingru Diao

Keyword(s):

Adsorption Capacity ◽

Photoelectron Spectroscopy ◽

Batch Adsorption ◽

Maximum Adsorption Capacity ◽

Cotton Stalk ◽

Magnetic Biochar ◽

X Ray ◽

Cotton Stalks ◽

Pseudo Second Order ◽

Co Precipitation

Abstract A magnetic cotton stalk biochar (MCSBC) was synthesized through chemical co-precipitation, based on cotton stalk biochar (CSBC). The MCSBC and CSBC were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and vibrating sample magnetometry. The characterization analyses showed that the magnetization process endowed the CSBC with excellent magnetic properties with a superparamagnetic magnetization of 27.59 emu/g. Batch adsorption experiment results indicated that the Cr(VI) maximum adsorption capacity of MCSBC was 20.05 mg/g, which was higher than that of CSBC (18.77 mg/g). The adsorption kinetic data were well fitted by the pseudo-second-order model and the adsorption isotherms were well represented by the Sips isotherm model. The thermodynamic studies indicated that the adsorption process was spontaneous and endothermic, and the entropy increased. The potential adsorption mechanism was the electrostatic adsorption of anionic Cr(VI) to the positively charged MCSBC surface, the reduction of Cr(VI) into Cr(III) and the complexation of Cr(III) by oxygen-containing functional groups of MCSBC. The regeneration studies showed that MCSBC kept 80% of its initial Cr(VI) adsorption capacity in the cycle. All the findings suggest that this novel magnetic biochar could be used in the field of Cr(VI)-containing wastewater treatment.

Download Full-text

A novel iron modified montmorillonite composite and its enhanced performance for tetracycline hydrochloride adsorption

Functional Materials Letters ◽

10.1142/s1793604719500140 ◽

2019 ◽

Vol 12 (02) ◽

pp. 1950014 ◽

Cited By ~ 3

Author(s):

Wei Yang ◽

Sheng Guo ◽

Jinyi Chen ◽

Abdul Naeem ◽

Hussain Fida ◽

...

Keyword(s):

Electron Microscopy ◽

Adsorption Capacity ◽

Photoelectron Spectroscopy ◽

Adsorption Process ◽

Interlayer Spacing ◽

Tetracycline Hydrochloride ◽

Maximum Adsorption Capacity ◽

X Ray ◽

Modified Montmorillonite ◽

Wide Ph Range

Iron-modified montmorillonite (Mt) composites with controlled interlayer spacing were successfully synthesized through Fenton-like process with the addition of different concentrations of Rhodamine B (RhB). The physicochemical properties of the resulting samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). It was worth noting that the adsorption efficiency of the composite for tetracycline hydrochloride (TC) increased with the increase of the RhB concentration during preparation. The maximum adsorption capacity of the as-prepared composite toward TC was 192.4[Formula: see text]mg/g, which was much higher than that of the Mt (144.9[Formula: see text]mg/g). Moreover, the as-prepared adsorbent showed high adsorption capacity of TC in a wide pH range of 3.0–9.0. The adsorption process followed the pseudo-second-order equation and the Langmuir isotherm model, suggesting the mono-layer chemisorption of the adsorption process. The present work may provide a new strategy for the design and fabrication of functional clay-based materials.

Download Full-text