scholarly journals Influence of Mineral Admixtures on Corrosion Inhibition Effect of Nitrites

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Mengna Yang ◽  
Junzhe Liu ◽  
Hui Wang ◽  
Yushun Li ◽  
Yanhua Dai ◽  
...  
Keyword(s):  
Fly Ash ◽  
Corrosion Inhibition ◽  
Ion Concentration ◽  
Mineral Admixtures ◽  
X Ray Diffraction ◽  
Nitrite Ion ◽  
X Ray ◽  
Inhibition Effect ◽  
Diffraction Patterns ◽  
Micro Analysis

Chemical quantitative analysis of effective anticorrosion component and micro-analysis of hydration products of fly ash and slag on the influence of the nitrites corrosion inhibition was studied by the free nitrite ion concentration and X-ray diffraction pattern. The free nitrite ion concentration was used to describe the corrosion inhibition effect of nitrites. And the X-ray diffraction patterns were used to analyze the adsorption properties. The research results show that fly ash and slag were beneficial for improving the corrosion inhibition effect of nitrites. Cement-based materials with slag at low content presented high free nitrite ion concentration, but the addition of low content of fly ash harmed the corrosion inhibition effect of nitrites. The specimens incorporated with both fly ash and slag can reach the highest free nitrite ion concentration when the compounding proportion was 1:1. It was concluded that the extent of mineral admixtures of the corrosion inhibition effect of nitrites was affected by its type and content.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

scholarly journals Influence of Inertia and Low Active Mineral Admixture on Strength and Microstructure of Cement-Based Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-9
Author(s):  
Meijuan Rao ◽  
Wan Tang ◽  
Wei Zhou ◽  
Yaning Kong ◽  
Shuhua Liu
Keyword(s):  
Fly Ash ◽  
Early Stage ◽  
Heat Of Hydration ◽  
Mineral Admixture ◽  
Limestone Powder ◽  
Mineral Admixtures ◽  
Inert Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cement Based Materials

Cement-based materials were investigated by comparing the strength and microstructure of pastes and mortar containing limestone powder or low quality fly ash. The compressive strength of the mortar at 28 and 90 d was examined whose microstructures were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis, and differential thermal analysis (TG-DTA). The results indicated that the strength of mortar decreased with increasing mineral admixtures. The limestone powder mainly acted as inert filler and hardly took part in the chemical reaction. Low quality fly ash may accelerate the formation of hydration products in samples with more chemically bonded water. This further resulted in a higher degree of cement hydration and denser microstructure, while the overall heat of hydration was reduced. At the early stage of hydration, low quality fly ash can be considered as an inert material whereas its reactivity at the later stage became high, especially for ground low quality fly ash.

Mechanical Characteristics of Concrete Exposed to External Flexural Load, De-Icing Salt and Freeze-Thaw Cycles

2011 ◽  
Vol 250-253 ◽  
pp. 33-39
Author(s):  
Xiao Lu Yuan ◽  
Bei Xing Li ◽  
Shang Chuan Zhao ◽  
Shi Hua Zhou
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Ordinary Portland Cement ◽  
Mechanical Characteristics ◽  
Concrete Strength ◽  
Mineral Admixtures ◽  
X Ray Diffraction ◽  
X Ray ◽  
Freeze Thaw

This paper investigates mechanical characteristics of concrete exposed to external flexural load, de-icing salt and freeze-thaw cycles. Concrete specimens made with ordinary Portland cement or ordinary Portland cement incorporating fly ash with the replacement of 10% or 20%, or 0.7/10000 air-entraining agent and 20% fly ash, or ground blast furnace slag with the replacement of 15% or 30%, were made and exposed to flexural load, freeze-thaw and de-icing salt environment. Mechanical properties of concrete including compressive strength and flexural strength were measured. Phase composition of samples was determined by means of x-ray diffraction (XRD). Results indicate that increasing flexural stress ratios reduced compressive strength and flexural strength of concrete, and presented higher improvement of mineral admixtures in concrete strength. Incorporation of mineral admixtures and air-entraining agent decreased the loss of concrete strength. X-ray diffraction analysis showed the presence of abundant calcium chloroaluminate and ettringite in paste samples.

Evaluation of Freezing Methods by Low Temperature X-Ray Diffraction

1977 ◽  
Vol 35 ◽  
pp. 330-333
Author(s):  
T. Gulik-Krzywicki ◽  
M.J. Costello
Keyword(s):  
Biological Materials ◽  
Molecular Organization ◽  
X Ray Diffraction ◽  
Glass Capillary ◽  
X Ray ◽  
Rate Dependent ◽  
Before And After ◽  
Freeze Etching ◽  
Diffraction Patterns ◽  
Set Up

Freeze-etching electron microscopy is currently one of the best methods for studying molecular organization of biological materials. Its application, however, is still limited by our imprecise knowledge about the perturbations of the original organization which may occur during quenching and fracturing of the samples and during the replication of fractured surfaces. Although it is well known that the preservation of the molecular organization of biological materials is critically dependent on the rate of freezing of the samples, little information is presently available concerning the nature and the extent of freezing-rate dependent perturbations of the original organizations. In order to obtain this information, we have developed a method based on the comparison of x-ray diffraction patterns of samples before and after freezing, prior to fracturing and replication.Our experimental set-up is shown in Fig. 1. The sample to be quenched is placed on its holder which is then mounted on a small metal holder (O) fixed on a glass capillary (p), whose position is controlled by a micromanipulator.

Examination of Rabbit Fc Crystals

1968 ◽  
Vol 26 ◽  
pp. 140-141
Author(s):  
J. P. Robinson ◽  
P. G. Lenhert
Keyword(s):  
Molecular Weight ◽  
Flat Plate ◽  
Phosphate Buffer ◽  
Asymmetric Unit ◽  
X Ray Diffraction ◽  
X Ray ◽  
Neutral Ph ◽  
Small Crystals ◽  
Carbon Coated ◽  
Diffraction Patterns

Crystallographic studies of rabbit Fc using X-ray diffraction patterns were recently reported. The unit cell constants were reported to be a = 69. 2 A°, b = 73. 1 A°, c = 60. 6 A°, B = 104° 30', space group P21, monoclinic, volume of asymmetric unit V = 148, 000 A°3. The molecular weight of the fragment was determined to be 55, 000 ± 2000 which is in agreement with earlier determinations by other methods.Fc crystals were formed in water or dilute phosphate buffer at neutral pH. The resulting crystal was a flat plate as previously described. Preparations of small crystals were negatively stained by mixing the suspension with equal volumes of 2% silicotungstate at neutral pH. A drop of the mixture was placed on a carbon coated grid and allowed to stand for a few minutes. The excess liquid was removed and the grid was immediately put in the microscope.

Control of the phase composition of advanced calcium phosphates using an x-ray diffractometer with a curved position-sensitive detector

2020 ◽  
Vol 86 (6) ◽  
pp. 29-35
Author(s):  
V. P. Sirotinkin ◽  
O. V. Baranov ◽  
A. Yu. Fedotov ◽  
S. M. Barinov
Keyword(s):  
Phase Composition ◽  
Calcium Phosphates ◽  
Position Sensitive Detector ◽  
Sensitive Detector ◽  
X Ray Diffraction ◽  
X Ray ◽  
Impurity Phases ◽  
Position Sensitive ◽  
Diffraction Peaks ◽  
Diffraction Patterns

The results of studying the phase composition of advanced calcium phosphates Ca10(PO4)6(OH)2, β-Ca3(PO4)2, α-Ca3(PO4)2, CaHPO4 · 2H2O, Ca8(HPO4)2(PO4)4 · 5H2O using an x-ray diffractometer with a curved position-sensitive detector are presented. Optimal experimental conditions (angular positions of the x-ray tube and detector, size of the slits, exposure time) were determined with allowance for possible formation of the impurity phases during synthesis. The construction features of diffractometers with a position-sensitive detector affecting the profile characteristics of x-ray diffraction peaks are considered. The composition for calibration of the diffractometer (a mixture of sodium acetate and yttrium oxide) was determined. Theoretical x-ray diffraction patterns for corresponding calcium phosphates are constructed on the basis of the literature data. These x-ray diffraction patterns were used to determine the phase composition of the advanced calcium phosphates. The features of advanced calcium phosphates, which should be taken into account during the phase analysis, are indicated. The powder of high-temperature form of tricalcium phosphate strongly adsorbs water from the environment. A strong texture is observed on the x-ray diffraction spectra of dicalcium phosphate dihydrate. A rather specific x-ray diffraction pattern of octacalcium phosphate pentahydrate revealed the only one strong peak at small angles. In all cases, significant deviations are observed for the recorded angular positions and relative intensity of the diffraction peaks. The results of the study of experimentally obtained mixtures of calcium phosphate are presented. It is shown that the graphic comparison of experimental x-ray diffraction spectra and pre-recorded spectra of the reference calcium phosphates and possible impurity phases is the most effective method. In this case, there is no need for calibration. When using this method, the total time for analysis of one sample is no more than 10 min.

Infrared spectroscopic study of the YPO4-YCrO4 system

1985 ◽  
Vol 50 (10) ◽  
pp. 2139-2145
Author(s):  
Alexander Muck ◽  
Eva Šantavá ◽  
Bohumil Hájek
Keyword(s):  
Spectroscopic Study ◽  
Infrared Spectra ◽  
Point Of View ◽  
Mixed Crystals ◽  
Crystal Symmetry ◽  
Infrared Spectroscopic Study ◽  
X Ray Diffraction ◽  
X Ray ◽  
Infrared Spectroscopic ◽  
Diffraction Patterns

The infrared spectra and powder X-ray diffraction patterns of polycrystalline YPO4-YCrO4 samples are studied from the point of view of their crystal symmetry. Mixed crystals of the D4h19 symmetry are formed over the region of 0-30 mol.% YPO4 in YCrO4. The Td → D2d → D2 or C2v(GS eff) correlation is appropriate for both PO43- and CrO43- anions.

scholarly journals Deep learning for visualization and novelty detection in large X-ray diffraction datasets

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Lars Banko ◽  
Phillip M. Maffettone ◽  
Dennis Naujoks ◽  
Daniel Olds ◽  
Alfred Ludwig
Keyword(s):  
Thin Film ◽  
Crystal Structure ◽  
Artificial Intelligence ◽  
Deep Learning ◽  
Novelty Detection ◽  
Structural Similarity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Diffraction Patterns ◽  
Post Hoc

AbstractWe apply variational autoencoders (VAE) to X-ray diffraction (XRD) data analysis on both simulated and experimental thin-film data. We show that crystal structure representations learned by a VAE reveal latent information, such as the structural similarity of textured diffraction patterns. While other artificial intelligence (AI) agents are effective at classifying XRD data into known phases, a similarly conditioned VAE is uniquely effective at knowing what it doesn’t know: it can rapidly identify data outside the distribution it was trained on, such as novel phases and mixtures. These capabilities demonstrate that a VAE is a valuable AI agent for aiding materials discovery and understanding XRD measurements both ‘on-the-fly’ and during post hoc analysis.

scholarly journals Simultaneous Multi-Bragg Peak Coherent X-ray Diffraction Imaging

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 312
Author(s):  
Florian Lauraux ◽  
Stéphane Labat ◽  
Sarah Yehya ◽  
Marie-Ingrid Richard ◽  
Steven J. Leake ◽  
...  
Keyword(s):  
Bragg Reflection ◽  
Volume Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Crystal Substrate ◽  
In Series ◽  
Diffraction Imaging ◽  
Diffraction Patterns ◽  
Lattice Planes ◽  
Oriented Parallel

The simultaneous measurement of two Bragg reflections by Bragg coherent X-ray diffraction is demonstrated on a twinned Au crystal, which was prepared by the solid-state dewetting of a 30 nm thin gold film on a sapphire substrate. The crystal was oriented on a goniometer so that two lattice planes fulfill the Bragg condition at the same time. The Au 111 and Au 200 Bragg peaks were measured simultaneously by scanning the energy of the incident X-ray beam and recording the diffraction patterns with two two-dimensional detectors. While the former Bragg reflection is not sensitive to the twin boundary, which is oriented parallel to the crystal–substrate interface, the latter reflection is only sensitive to one part of the crystal. The volume ratio between the two parts of the twinned crystal is about 1:9, which is also confirmed by Laue microdiffraction of the same crystal. The parallel measurement of multiple Bragg reflections is essential for future in situ and operando studies, which are so far limited to either a single Bragg reflection or several in series, to facilitate the precise monitoring of both the strain field and defects during the application of external stimuli.

Sign in / Sign up

Export Citation Format

Share Document